AIYIMA T5 Bluetooth Channel Digital Amplifier User Manual
- June 15, 2024
- AIYIMA
Table of Contents
AIYIMA T5 Bluetooth Channel Digital Amplifier
Front Panel Function Description
- VU level meter
- Bluetooth mode indicator (wait for pairing to blink, and the connection is successful)
- RCA mode indicator
- MM phono mode indicator light
- 6.35 headphone output interface
- Pummer victor, snot piss to swine musts, et to presume to decrease, right turn to increase the volume)
- Bass gain adjustment (‡6DB)
- Treble gain adjustment (‡6DB)
- Tube
Rear Panel Function Description
- MM phono ground wire binding post (connect the phono ground wire here to reduce the phono noise)
- 3.5MM audio signal output (which can be connected to active speakers, active subwoofers or power amplifiers)
- Right channel output interface
- Left channel output interface
- DC power input interface (can be connected to 18-36V DC power supply)
- MM phono signal input interface
- RCA audio signal input interface
- Bluetooth antenna.
Features And Functions
- Built-in RIAA characteristic HIFI MM phono amplifier function
- Support RCA audio input
- Support Bluetooth audio playback
- Support 3.5MM full-frequency output
- Support 6.35MM amp output
- Support treble and bass adjustment
- Support VU level indication
- Support tube
Specifications
| Output Power | 160W+160W(40 load) | Input Sensitivity | 0.775V |
|---|---|---|---|
| Frequency Response | 20Hz-20KHz (±3D8) | Channel System | 2.0 |
| Audio Input | MM phono, Bluetooth, Audio input | Speaker Impedance | 2-80 |
| Bluetooth Version | 5.1 | Headphone Output Power | 320 12SmW |
| Bluetooth Audio Format | SBC, AAC, APTX, APTX-HD, APTX-LL | Power Input |
DC18-36V (5-12A)
SNR| 90dB| Dimensions| 13310554mm
Distortion| ,;Q.1% (1KHZ 1W)| |
Packing List
- Amplifier
- 1 unit
- Power adapter
- 1 рс
- Electronic tube
- 2 pcs
- Bluetooth Antenna
- 1 pc
- Instruction manual
- 1 pc
Frequently Asked Questions
Q: I have all the wires connected, but no sound output.
- Check whether the POWER indicator is on or not. If it is not on, press the POWER boot button to start the machine. After pressing the power button, the indicator will still not go on. At this point, you can find a laptop to connect it to the power supply for testing to determine whether it is a machine failure or a power failure.
- If the indicator light is on, check whether the VOL knob is in the minimum state; if it is in the minimum state, it will be normal if it is rotated clockwise
- If the above two points are normal, check whether the input device is paused, mute, or at a minimum volume.
Q: Why does the sound break?
A: the amplifier exceeds the normal output power, there will be a greater
distortion of the situation, at this point, you put the front volume or
amplifier volume down on the normal.
Q: Why does the loudspeaker produce a loud electric sound?
A: If you are not using the original standard power supply, please replace the
power supply and test again. Many power sources in the market have a large
ripple interference coefficient, which will cause a large current sound.
Q: Why does the speaker make a lot of noise when I plug in the input cord
and don’t connect the playback source?
A: use the signal line without a shield, there will be an interference signal
into the amplifier, if you hate the sound suggest you replace the signal line
with a shield or pull out the signal line.
Q: Why does my amplifier stop working after some time, then stop working
after some time?
A: Usually in this case, the amplifier is overheated and the output power may
have exceeded the design power. At this point, you can lower the volume a
little and try again.
Q: Why does the volume stay the same, but the volume is different when
connected to different sources (such as a CD and then a mobile phone)?
A: The output range of different types of audio devices is different. Mobile
phones are usually 0.35V, while CDS is 1V. The output signal amplitude of the
sound source will directly affect the sound size.
Q: Does this machine handle phonographs/record players?
A: Yes, connect the output line of the phonograph/record player to the
corresponding interface of the machine, and then switch the function switch to
the “PHONO” file.
Shenzhen Yima Technology Co.,Ltd
- Website:www.aiyima.com
- Telephone: 86-0755-28268551
- Location: 4F, Building 7 Hekan industrial park. Wuhe South Road 41. Long-Gang district. Shenzhen. CHINA. 518000
- Email: sale@aiyima.com
- VK: https://vk.com/aiyima
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>