binardat IE6050 5 Port Din Rail Industrial Ethernet Switch User Manual
- June 15, 2024
- binardat
Table of Contents
Industrial Ethernet Switch
User Manual
Industrial Ethernet Switch User Manual
Product Description
The industrial Ethernet switch provides excellent industrial quality, such as vibration resistance, high/low temperature, dustproof and surge protection, through the design of fanless heat dissipation circuit, wide range working environment temperature, high protection grade and so on. Moreover, it integrates a variety of rich protocols such as routing, switching and security, which greatly improves the flexibility of networking and enhances the reliability and security of industrial networks. It can also meet the deployment equirements of rail transit, safe city, intel ligent transportation, outdoor monitoring and other harsh environments.
Indicator Lamp and DIP
Indicator Lamp Meaning Contrast Table 1-1
| Indicator Light | State | Meaning |
|---|---|---|
| Status | System status | |
| indicator | ON | System initialization or |
System abnormality
Twinkle| Working normally
OFF| Not powered
Power| Power
indicator| ON| Power supply is normal
OFF| Not powered
Network
port
status
light| Green lamp (rate /PoE
status
indicator)| ON| Port maximum rate
Port POE is powering up
OFF| Port is operating at a non
maximum rate
Port POE is not powered
Yellow lamp (Link/ACT)| ON| Port link
Twinkle| Port has message interaction
fiber
status
light| Green lamp
(Link/ACT)| ON| Port link
Twinkle| Port has message interaction
Reset| Restore factory/ restart| Long press (> 20S)
Managed DIP Switch Meaning Contrast Table 1-2
| DIP Switch | Function | ON State | OFF State |
|---|---|---|---|
| Bit 1(silk screen: 0-Ring) | Ring network | ON | OFF |
| Bit 2(silk screen: C-F1) | Custom function | ON | OFF |
| Bit 3 (silk screen: C-F2) | Custom function | ON | OFF |
Device Installation
Installation description :
Industrial Ethernet switch adapts DIN rail installation.
- Tilt the device up, make the clasp on the upper end of the device buckle on the DIN rail.
- Press down the device so that the lower end of the buckle is buckled into the DIN rail.
- Check that whether the inspection is stable after buckle.
POE Line Seauence Introduction
POE is a technology that uses Power over Ethernet, the device supports 802.3AF and 802. 3AT standards, It is required that the switch power supply should be between DC 48V and DC 57V, POE connection should be consistent with the network cable connection, and 1, 2, 3 and 6 cables should be used as both data transmission and POE power supply.
Power Input
Industrial Ethernet switches are dual power backup, When all two power supplies are connected, only one power supply works. When this power fails, it automatically switches to another power supply to achieve redundant protection of the power supply. The meaning of power wiring is shown in Table 1-3.
| Pl+ | First circuit power supply positive pole |
|---|---|
| Pl- | First circuit power supply negative pole |
| RSV | Extended functions |
| RSV | Extended functions |
| P2+ | Second circuit power supply positive pole |
| P2- | Second circuit power supply negative pole |
Note: Please connect the positive and negative pole according to the
terminal of the Phoenix terminal and input voltage according to the voltage
range. (Generally DC12-57V, based on the description of side cover) Only one
power supply can work properly.
Power installation is shown as following diagram (Only for the schematic
diagram, not including all panels, the wiring is based on the positive and
negative pole):
Accessories List
| Name | Quantity |
|---|---|
| Switch | 1PCS |
| Phoenix terminal | 1PCS |
| Power Ada pter | 1PCS |
| User manual & Warranty card | 1PCS |
Get help or claim warranty Visit Here: www.binardat.com/support/ or Scan QR Code
Wuhan niannianxingchen Technology Co.,Ltd.
No. 349 Guanshan Road, Gaoxin Avenue, Wuhan, Hubei, China
support@binardat.com
www.binardat.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>