VEVOR 12 Ton Hydraulic Bottle Jack User Manual
- June 15, 2024
- VEVOR
Table of Contents
VEVOR 12 Ton Hydraulic Bottle Jack
Important Information
We continue to be committed to provide you tools with competitive price. “Save Hair’. “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us If you are actually saving half in comparison w~h the lop major brands.
OPERATION INSTRUCTIONS
+ To raise: Using the slotted opening at the end of the handle, tum the release-valve clockwise to lighten it. And then put the jack under the load to be lifted. Turn the adjustable screw rod until it contacts with the load, Put the handle in the pressing handle holder and press up the down; the piston rod will rise slowly lull the specified range is reached.
THIS IS A LIFTNG DEVICE ONLY. IT IS DESIGNED TO LIFT PART OF THE TOTAL VEHICLE (ONE WHEEL OR AX.LE.ALWAYS WEAR SAFETY GLASSES WHEN USING THIS EQUIPMENT CENTER LOAD ON SADDLE BEFORE LIFTING NEVER WORK ON.UNDER OR AROUND LOAD UNTIL IT IS PROPERLY SUPPORTED.TRANSFER THE LOAD IMMEDIATELY TO APPROPRIATE LYRATED JACK STANDS DO NOT USE THIS PRODUCT FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS INTENOED. IT IS OWNER’S RESPONSIBILITY TO KEEP LABELS AND MANUALS ARE AVAILABLE FROM THE MANUFACTURER FAILURE TO HEED THESE AND ALL OTHER WARNINGS PERTAINING TO THIS PRODUCT CAN RESULT IN SUDDEN LOSS OF LIFTED LOAD RESULTING IN DEATH PERSONAL INJURY OR PROPERTY DAMAGE.
+To lower: Remove the pressing handle. Using the slotted opening at the
end of the handle 1um the release-valve slightly counter clock wise to loosen
it. And then the piston rod will move down slowly. When loaded. the release-
valve should not be timed quickly, otherwise too speedy lowering will lead to
danger.
BE SURE ALL TOOLS AND PERSONNEL ARE CLEAR BEFORE LOWERING LOAD, DANGEROUS DYNAMIC SHOCK LOADS ARE CREATED BY QUICKLY OPENING AND CLOSING THE RELEASE VALVE AS THE LOAD IS BEING LOWERED THE RESULTING OVERLOAD MAY CAUSE HYDRAULIC SYSTEM FAILURE, WHICH COULD CAUSE SEVERE PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR SAFETY$ SAKE
Lifting weight should not exceeded the specified duty of this jack. (Max.
watch box) The bottom of the jack should always be placed on the leveled and
hard ground.
The contact between the top and the lifted body must be perfect.
Without a supporting rack, it is not allowed to work under the lifted heavy
body after it is raised.
When several jacks are used together, the raising speed should be coincident
with each other and the duty of each should be balanced, otherwise the danger
of topping over \’.ill happen.
ROUTINE MAINTENANCE
Proper quantity of oil should be maintained, otherwise the specified lifting
height would not be reached.
When in operation, the jack should be seated in rectangular angle with the
lifted heavy body, and to avoid piston and screw top cracking no crookedness
should be allowed.
To avoid damaging, the jack should be kept from shocking while in operation.
The jack is not allowed lo stand an one side or upside down.
This product is not suitable to the operation environment full or acid
alkaline corrosive air.
Adding oil
- With saddle fully lowered and pump piston fully depressed. set jack in its upright, level position. Remove oil filler plug.
- Fill until oil is level with the filler plug hole, reinstall oil filter plug.
Changing oil
For best performance and longest life , replace the complete fluid supply at least once per year.
-
With saddle fully lowered and pump piston fully depressed, remove the oil filler plug.
-
Lay the jack, on its side and drain the fluid into a suitable container.
Note: Dispose of hydraulic fluid in accordance with local regulations -
Fill with good Quality jack oil. Reinstall oil filler Plug. We recommend Mobil DTE 13 or equivalent.
Lubrication
-
A coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure that wheels, casters and pump assemblies move freely.
-
Periodically check the pump piston and ram for signs of rust or corrosion.
Clean as needed and wipe with an oily cloth.
NEVER USE SANDPAPER OR ABRASIVE MATERIAL ON THESE SURFACES. -
When not in use, store the jack with pump piston and ram fully retracted.
-
DO NOT ADJUST THIS VALVE
Structural Composition
PART LIST
ITE M No .| DESCR I P TI O N| Q
T Y
---|---|---
1| WIRE PIN| 2
2| PIN| 2
3| PISTON| 1
4| “O” RING| 1
5| BACK-UP RING| 1
6| U-SEAL| 1
7| PISTON PUMP| 1
8| GASKET| 1
9| PLUG ADDING OIL| 1
10| HANDLE SOCKET| 1
11| OIL TANK| 1
12| SEAL| 1
13| TOP TANK| 1
14| “O” RING| 1
15| PISTON ROD| 1
16| BACK-UP RING| 1
17| “O” RING| 1
---|---|---
18| STEEL BALL 1/4″| 3
19| SEAL| 1
20| GASKET| 1
21| CYLINDER| 1
22| RELEASE VALVE| 1
2| SEAL| 1
24| SCREW| 1
25| “O” RING| 1
26| SCREW| 1
27| COMPRESSION SPRING| 1
28| BACK I NG PIN| 1
29| STEEL BALL 3/16″| 1
30| BASE| 1
31| FRONT HANDLE, LOWER| 1
32| MIDDLE HANDLE, LOWER| 1
33| REALHANDLE, LOWER| 1
Parameter table
Model| Lifting Capacity (TON)| Max Altitude (mm)| Min
Altitude (mm)| Lifting Altitude (mm)| Regulating Altitude (mm)|
Net Weight ( kg)
---|---|---|---|---|---|---
QJD-01-0 12A| 12| 355| 190| 105| 60| 5.8
QJD-01-0 20A| 20| 450| 240| 1 50| 60| 9 . 6
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us: CustomerServlce@vevor.com
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
CUSTOMERS SUPPORT
TOUGH TOOLS, HALF PRICE
Technical Support and E-Warranty Certificate
https://www.vevor.com/support
Made In China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>