VSVABEFV B0CM8XRZG2 WiFi Bridge 300Mbps 2.4G Long Range Point Installation Guide

VSVABEFV B0CM8XRZG2 WiFi Bridge 300Mbps 2.4G Long Range Point Installation Guide

Get Started to Know Your Wireless Bridge:

CPE Bridge For Video Transmission Introduction:

CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems and so on.

CPE Video Bridge Transmission usually consists of two devices in AP and Client mode respective- ly. At the Client-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment.

Outdoor CPE Function:

1. Long-distance 5.8G wireless transmission equipment
2. Support point-to-point, point-to-multipoint mode
3. Transmission distance up to 3km (Barrier-Free)
4. WDS networking mode, video network dual compatible.
5. Dialing to set the transmitter and receiver, and also support the PC to modify the IP settings.
6. Dynamic MIMO power saving mode (DMPS) and automatic power-saving transmission (APSD)

Outdoor CPE Specification:

Master control : AR9344
DRAM : DDR2 64MByte
FLASH : 8MByte
Wired Interface : 10/100Mbps LAN*2
Transfer method : Direct Sequence Spread Spectrum (DSSS)
Modulation : OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Network Standard : IEEE802.11n, IEEE802.11a, IEEE802.3u
Supporting agreement : CSMA/CA TCP/IP, IPX/SPX, NetBEUI, DHCP,NDIS3, NDIS4, NDIS5
Frequency Range : 4900~6100MHz
Power consumption : ≤3W
Power scheme : POE 24V 1A
Antenna gain : 14DBi
Management settings : WEP management, Telnet, Serial
Encryption : WEP encryption 64/128bits, WPA, WPA2, 802.1x
Operating temperature : -30℃~65℃

Connection Diagram:

a. Transmitting Side:

b. Receiving Side:

Digital Display Wireless Bridge Set Up:

The digital display bridge is simply connected by dialing. After setting Bridge 1 and Bridge 2 to A and B mode, set the two bridges to the same number (1,2,3, F ) through the “reset” button, then the two bridges can be automatically connected without using a computer for IP setting. The dialing settings are only connected using a point-to-point bridge, which is not suitable for point-to-multipoint connections.
Digital Bridge-A Master Mode

Digital Bridge-B Slave Mode

6.2
Before connecting the power supply, move the bridge 1 to the A end through the A-B button, and the bridge 2 moves to the B end through the A-B button, the A end represents the receiving mode, the B end represents the transmitting mode; The bridge 1 and the bridge 2 are respectively set after A and B. Connect the bridge to the power supply, the digital display shows “L” and flashes, and the “L” disappears to indicate that the configuration connection is successful.

6.3
The reset button to set the led digital display, click once the startup configuration status, continue to click, the number will increase, can be continuously increased. Assume that a pair of bridges with a number of 3 is configured After bridge 1 set to 3, after the bridge 2 set to 3, first the LED light will flash, then “L” flashes to indicate the application is being configuration, please be patient, When “L” flashes, it will become the number “3”, and the number “3” will continue to flash until the bridge 1, bridge 2 is connected after the success, the LED display “3” is always on, not flashing, indicating that the bridge 1 and bridge 2 has been successfully networked.

LED Indication Chart:

WLAN| After the bridge is connected successfully, the WLAN light will be on, not connected the WLAN light will not be lit.
---|---
LAN1/LAN2| The data connection is successful, the LED light is on, otherwise, it is not Wight.
PWR| Power indicator, the LED is on after the power is connected
LED| Digital display LED display “H” indicates manual configuration status
LED| Digital display LED display V and flashing indicates settings status
LED| Digital display LED flashing indicates edit the config or connecting
Point Light| A, B status lights, lighting is B mode, no lighting is A mode.
RST| Click once, the LED display number increases, looping from 0, 1, …. F.
RST| Press over 10s, release the “reser button, the system automatically restarts

LED Number & IP Chart:

CPE Advanced Settings, Suitable for Point-to-multipoint:

Since the Bridge devices are mainly used for long-range signal bridge and repeating, and to avoid IP address confliction when the CPE is connected with another router device, our bridge products disable the DHCP function (automatic IP address assignment) by default, you need configure the CPE at the first time to use it properly. Pls configure your PC IP as 192.168.255.xxx (xxx is a figure 2-254), and then pls connect the CPE as the diagram below. Then power on CPE, input 192.168.255.100 at the IE bar, then input user name and password at the user interface to enter into the configuration page.
CPE Default IP : 192.168.255.100 (Reference LED Number & IP Chart Setting IP) CPE Default User Name and Password: admin/admin

How to Configure Your PC IP As 192.168.255.xxx :
a. Find the network icon in the lower right corner and click Open Network and Internet Settings.

b. Select Ethernet and Click the Change Adapter Option.

c. Find the network connection you are using and right click on Properties.

d. Double-click the IPV4 setting, select the IP address below, enter the IP and confirm.

e. Configure your PC IP as 192.168.255.xxx (xxx is a figure 2-254), note that the set PC IP cannot be the same as the IP of the СРЕ.

Bridge Configuration (WEB UI):

Note: Before configuring the Bridge IP, AP Configuration, Client Configuration, make sure that the PC and CPE are properly connected and that the PC IP is configured.

Computer Setup Debug Connection Diagram:

Configure Bridge IP:
Please assign a different IP address to each CPE under the same local area network for easy management.

Wireless Receiver Mode (Receiving Point)
Select “A(Master)” under the “Mode”, then select Matching ID (Such as “64(5320Mhz)”), The matching IDs of A(Master) and B(Slave) must be the same. Create an easy-to-remember name for your wireless network in Hostname. See figure below:

Wireless Transmission Mode (Transmission Point)
Select “B(Slave)” under the “Mode”, then select Matching ID (Such as “64(5320Mhz)”) The matching IDs of A(Master) and B(Slave) must be the same. Create an easy-to-remember name for your wireless network in Hostname.

See figure below:

WEB UI Diagram

CPE Connection Diagram:

Field Applications:

Point to Point Connection:

Network Diagram

kilometers (no blocking obstacles
The CPE connects to the POE port of the POE power adapter, the LAN port of the POE power adapter connects to the IP camera.

The CPE connects to the POE port of the POE power adapter, the LAN port of the POE power adapter connects to switch or video recorder.

Point o to t Multi-Point Connection:

kilometers (no blocking obstacles

The CPE connects to the POE port of the POE power adapter, the LAN port of the POE power adapter connects to the IP camera.

The CPE connects to the POE port of the POE power adapter, the LAN port of the POE power adapter connects to switch or video recorder.

Multiples Clients Connection:

Network Diagram

kilometers (no blocking obstacles)

The IP cameras all connect to the switch, the LAN port of the POE power adapter connects to the switch, and POE port of the POE power adapter connects to the CPE

The CPE connects to the POE port of the POE power adapter, the LAN port of the POE power adapter connects to switch or video recorder.

Wireless Surveillance Connection for Elevator Well:

There should be no blocking obstacle between the two CPEs
The CPEs at the receiving side are installed on the celling or bottom of the elevator well, and then connected to video recorder by wired cable
At the IP camera side, the CPEs are installed on top of the elevator room.

There should be no blocking obstacle between the two CPEs
CPE LAN port connects with POE port of the POE power adapter, and the LAN port of the POE power adapter connects with the switch or video recorder.

Tips: When you encounter any problems with this outdoor CPE, please contact us in time, we will provide technical support. 40

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>