Danfoss RET1001M – V2 Room Thermostat Installation Guide

June 15, 2024
Danfoss

Danfoss RET1001M – V2 Room Thermostat

Product Information

Specifications

  • Operating voltage: Volt free
  • Switch rating: 3A (1) at 250Vac
  • Switch type: 1x SPDT Type 1B
  • Terminals: max 2.5 mm2 wires
  • IP rating: IP30 (installed)
  • Load compensation control: Yes
  • On/off control: Yes
  • ErP class: Class IV, efficiency gain 2%
  • Construction: EN60730-2-9
  • Control pollution situation: Degree 2
  • Rated impulse voltage: 4 kV
  • Dimensions: H86 x W86 x D37
  • Software classification: A

Product Usage Instructions

Installation Steps

  1. Installation must be done by an authorised electrician.
  2. The room thermostat should be installed at approximately 1.5 m above the floor and away from sunlight, draught, or other heat sources (e.g., TV’s).
  3. Loosen the lower retaining screws and carefully remove the back plate.
  4. Mount the back plate directly to the wall or on a wall box and wire it according to the application.
  5. Locate the hooks at the top of the front part into the top of the back plate and lower it into position. Tighten the retaining screws.

Dimensions and Wiring
Refer to Figure 4 for dimensions and Figure 5 for the wiring diagram on page 45 of the manual.

LED Indicators

  • Power on – Green
  • Thermostat Output on – Red

Control Type Setting
Move the link to the required position.

Limiting
Refer to the manual for details on limiting.

Technical Specifications

  • Product is designed for continuous use
  • Operating voltage: Volt free
  • Switch rating: 3A (1) at 250Vac
  • Switch type: 1x SPDT Type 1B
  • Terminals: max 2.5 mm2 wires
  • IP rating: IP30 (installed)
  • Load compensation control: Yes
  • On/off control: Yes
  • ErP class: Class IV, efficiency gain 2%
  • Construction: EN60730-2-9
  • Control pollution situation: Degree 2
  • Rated impulse voltage: 4 kV
  • Dimensions: H86 x W86 x D37
  • Software classification: A

Frequently Asked Questions (FAQ)

  • Q: Who should install the thermostat?
    A: The installation must be done by an authorised electrician.

  • Q: Where should the room thermostat be installed?
    A: The room thermostat should be installed at approximately 1.5 m above the floor and away from sunlight, draught, or other heat sources (e.g., TV’s).

  • Q: What are the LED indicators for?
    A: The green LED indicates power on, and the red LED indicates thermostat output on.

  • Q: What is the control type setting?
    A: The control type setting refers to moving the link to the required position.

  • Q: What are the technical specifications of the product?
    A: The technical specifications include the operating voltage, switch rating, switch type, terminals, IP rating, load compensation control, on/off control, ErP class, construction details, control pollution situation, rated impulse voltage, dimensions, and software classification.

Installation Steps

  1. Installation must be done by an authorised electrician.
  2. The room thermostat should be installed at approx. 1.5 m above floor and where the effects of sunlight, draught or other heat sources (eg. TV’s) are avoided, see fig. 1. on page 44.
  3. First loosen lower retaining screws and carefully remove back plate, see fig . 2 on page 44.
  4. Mount back plate direct to wall or on wall box and wire according to application, see fig. 3 on page 44 & fig. 5 on page 45 according to application.
  5. Locate hooks at top of front part into top of back plate and lower into position and tighten retaining screws.

Dimensions and Wiring

See fig. 4 for dimensions and fig. 5 for wiring diagram on page .Danfoss-
RET1001M-V2-Room-Thermostat-01 \(7\)

Danfoss-RET1001M-V2-Room-Thermostat-01 \(8\)* Note

  1. Both live (L) terminals are internally linked and available for ease of cable termination only.
  2. If replacing a 230-volt room stat, a link between the live(L) and a common(COM) terminal is required.

LED indicators

  • Power on – Green
  • Thermostat Output on – Red

Control type setting

Move link to required position.Danfoss-RET1001M-V2-Room-Thermostat-01
\(1\)

  • Load Compensation Control – energy saving feature which fires the boiler at regular intervals to maintain a set temperature, achieving a constant ambient environment for the user. (factory default)
  • ON/OFF Control – boiler is switched ON when below set temperature and OFF when above.

Limiting

Limiting – allowing the user to alter the temperature within a predefined range, which is less than the full range of the product (i.e. between 18-22 °).Danfoss-RET1001M-V2-Room-Thermostat-01 \(3\) Danfoss-RET1001M-V2-Room-Thermostat-01 \(4\)

Technical Specifications

Specifications RET1001M V2
Operating Product is designed for continuous use
Operating voltage 230Vac ±10% 50/60Hz
Output Volt free
Setting temperature range 5 °C to 30 °C
Operating temperature range 0 °C to 40 °C
Switch rating 3A (1) at 250Vac
Switch type 1x SPDT Type 1B
Terminals max 2.5 mm2 wires
IP rating IP30 (installed)
Load compensation control Yes
On/off control Yes
ErP class Class IV, efficiency gain 2%
Construction EN60730-2-9
Control pollution situation Degree 2
Rated impulse voltage 4 kV
Ball pressure test 75 °C
Dimensions H86 x W86 x D37
Software classification A

This product is an electronic controller for the control of central heating.

Danfoss Ltd.
22 Wycombe End, HP9 1NB, GB

Danfoss A/S
Heating Segment

Any information, including, but not limited to information on selection of product, its application or use, product design, weight, dimensions, capacity or any other technical data in product manuals, catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or via download, shall be considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility for possible errors in catalogues, brochures, videos and other material. Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to form, fit or function of the product. All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved.

© Danfoss Climate Solutions | 11.2022
AN30483292054501-000102
www.danfoss.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals