OEMIRY OM-CF02 Countertop Water Filtration System User Manual
- June 14, 2024
- OEMIRY
Table of Contents
MODEL NO: OM-CF02
Countertop Water Filtration System
User Manual
About the System
Thanks for choosing OEMIRY Countertop Faucet Water Filtration System. The product adopts activated carbon block to provide you with healthy water and release beneficial minerals. Its multistage filtration can reduce harmful substances such as chlorine lead, fluoride, arsenic, etc. Also, it inhibits the bacteria from building up. The filtration system is made of eco-friendly ABS material to ensure quality and durability, and the precise design makes it easy to install. The system doesn’t need a power supply while it produces no waste water. You can get both tap water and filtered water by a switch.
System Specifications
Filtration Model No………………………. 0M-CF02
Replacement Filter Model No. ……………………….0M-RFO2
Rated Capacity ……………………….8000 gallons or 12 months
Rated Flow ……………………….1.6gpm/6Ipm (tested under 60psi)
Operating Temperature………………………. 41-100°F / 5-38°C
Working Pressure………………………. 15-100 psi / 100-689 kPa
NOTE:
Do not use water that is microbiological unsafe or of unknown quality without
adequate disinfection before or after use of the system
Parts List
(A) Filter cover
(B) Filter
(C) Filter base
(D) Spout
(E) Mounting base
(F) Wrench
(G) A3 adapter (15/16”-27)
Ad adapter (13/16”)
AS adapter (18.5)
AG adapter (M21.5)
B4 adapter (M18.5)
Installation Instructions
- Take out the system and accessories.
- Remove the faucet’s aerator and choose the right adapter to match your faucet threading. Make sure the washer between faucet and the the system is installed firmly.
How to choose the right adapter
For external threaded faucets, please 1 connect the adapter directly to the
; mounting base (E). Please select adapter(B4) if the mounting base(E) is
Not fitted to the faucet.
For internal threaded faucets, select the appropriate adapter (A3/A4/A5/A6)
according to the thread size, connect it to the faucet and tighten them with a
coin like below. Make sure the white sealing ; ring is in the mounting base
(E), then connect the adapter to the the mounting base(E), please install it
firmly.
- Tighten the filter cover (A) with a wrench (F). (Figure 1.1)
- Put the water system in its proper position. Switch the lever to the level position and run water to the system slightly. Flush it for 3-5 minutes before the first use. (Figure 1.2)
Tips: If there is water leakage at the connecting position between the
faucet and the system, it is recommended to use a wrench to help tightening
the nut on, or use the Teflon tape inside the instruction package to avoid
leakage. If water still leaks, please put another 1.5mm sealing ring (in the
package) on mounting base, then install it firmly to avoid leakage.
NOTE: There may be a small amount of black water during the first use,
don’t worry and this is a normal phenomenon because of the activated carbon.
Please use the water after it becomes clear.
Use Method
- Switch the lever to the downward direction to get tap water. (Figure 1.3)
- Switch the lever to the level direction to get the pure water. (Figure 1.4)
NOTE:
-
Before the first use, flush it for 3-5 minutes in the “pure water” position.
Do not run water at a temperature higher than 100°F / 38°C. There may be a small amount of black water and the sound of water pushing air out of the filter during the first use. This is a normal phenomenon because of the activated carbon. Please use the water after it becomes clear. -
Check for water leaking, please contact customer service instantly to get help when it happens.
Filter Replacement
For optimum performance, we recommend you use our original OEMIRY faucet replacement water filter. To keep water fresh and healthy, we advertise you to change your fiter every 12 months or 8000 gallons, whichever comes first. This will vary based on your waste usage and water quality.
- Place the system in the water sink, and use the wrench (F) to unscrew the filter cover (A) from the top(there will be some water between the filter housing and the base).
- Remove the expired filter from the system and insert the new filter into the base (C). Make sure the sealing ring on the filter cover is installed firmly.
- Screw the filter cover (A) into the base (C) by hand and tighten it with wrench (F).
- Tum on the faucet and flush for 3.5 minutes.
Warnings
- Do not run water at a temperature higher than 100°F / 38°C.
- Flush the filter for 3-5 minutes before the first use or after filter replacement.
- If the system has not been used for over 24 hours, run water for 1 minute before use.
- Do not touch the filtered water outlet of the system in order to prevent bacteria from building up.
- Protect the filter system from freezing temperature, frost, snow, sleet, and ice.
- Clean the exterior of the system with a soft cloth to maintain its appearance and service life.
- Replace the filter every 12 months or 8000 gallons for best filtration performance.
Frequently Asked Questions
Q: Why does the filtered water taste weird?
A: The filter is not installed appropriately, or it should be replaced. Please re-install item a correct way. If the taste is still bad, we suggest you replace a new filter.
Q: Why does the TDS value not lower after filtration?
A: TDS stands for total dissolved solids. It is composed of inorganic salts and a small amount of organic matter. This system cannot lower the TDS value because it removes harmful substances while keeping beneficial trace elements, which can increase the TDS value.
Q: Why does water leak between the mounting base and the faucet?
A: Remove the filtration system from the faucet and check it whether the O-ring at the connection is placed correctly. Ensure the thread between faucet and filtration system is screwed firmly so the O-ring can work.
Q: Why is the water leaking or dripping?
A: Check it whether the selected adaptor is correct, or whether the adaptor sealing ring and the base sealing ring are installed firmly. Also check it f the spout (D) and the filter base (C) are installed in place. Flush the filter for 3-5 minutes to activate it, and there will not be water leaking or dripping.
Limited Warranty
The OEMIRY activated carbon block faucet filtration system (model No: OM-CF02)
offers 1-year warranty, which covers defects in materials and workmanship from
the original date of purchase. If the product proves to be defective within 1
year from the date of purchase, please contact us get support via Customer
Service Center. During the warranty period, we will replace or repair any part
that is deemed to be defective if the product has not been subjected to
tampering, alteration, or improper use after delivery, and has not been
repaired by the manufacturer. The product is not warranted against misuse, use
in abnormal temperature conditions, conditions listed outside the operating
parameters, or use in commercial operations or any other manner outside the
“system specification” set forth in the owner’s manual. Our obligation does
not include the cost of transportation. We are not responsible for damage in
transit; claims for such damage should be presented to the carrier by the
customer.
NOTE:
The warranty does not apply to any filter cartridge, which has a life
expectancy that varies based on incoming water quality.
B2 Online Technical Support: Beheal7@outiook.com
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>