ALPOWL B08F9X3LZ6 Professional Audio Mixer Sound Board User Manual

ALPOWL B08F9X3LZ6 Professional Audio Mixer Sound Board User Manual

SAFETY INSTRUCTIONS

CAUTION:
To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel.

WARNING:
To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture.

This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to the important operating and maintenance instructions in the accompanying literature. Read the manual.

DETAILED SAFETY INSTRUCTIONS:
All the safety and operation instructions should be read before the appliance is operated.

Retain Instructions:
The safety and operating instructions should be retained for future reference.

Heed Warnings:
All warnings on the appliance and in the operating instructions should be adhered to.

Follow instructions:
All operation and user instructions should be followed.

Water and Moisture:
The appliance should not be used near water (e. g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool etc.).

Ventilation:
The appliance shoule be situated so that its location or position does not inerfere with its proper ventila- ton. For example, the appliance shoule not be situated on a bed, sofa rug, or similar surface that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

Heat:
appliance shoule be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.

Power Source:
The appliance should be connected to a power supply only the type described in the operating instructions or as marked on the appliance.

Grounding or Polarization:
Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.

Power-Cord Protection:
Power supply cords should be routed so that they are not likely to be walded on or ponched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles and the point where they exit from the appliance.

Cleaning:
The appliance should be cleaned only as recommended by the manufacturer.

Non-use Periods:
The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

Object and Liquid Entry:
Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

Damage Requiring Service:
The appliance should be serviced by qualified service personnel when:

• the power supply cord or the plug has been damaged; or
• objects have fallen, or liquid has been spilled into the appliance; or
• the appliance has been exposed to rain; or
• the appliance does not appear to operate normally or exhibits a marked change in performance; or
• the appliance has been dropped, or the enclosure damaged.

Servicing:
The user should not attempt to service the appliance beyond that which is describe in the Operating I Instructions. All other servicing should be referred to qualified service personnel.

PROFESSIONAL 4 channel mixing console and Aux paths plus effects processor

• 4-channel mixing console with two stereo channels and a separate stereo tape channel
• Separate input JACK controls for mic and line inputs noall mono channels
• Low-noise, discrete mic preamplifiers on all microphone inputs.
• Dedicated inserts on al mono channels
• Balanced 1/4″ stereo jacks and balance controls on all stereo channels
• Separate stereo tape channel with 1/4″ and RCA jacks
• Stereo output for recording applications
• English musical active 3-babd EQ on all seven channels.
• AUX and effects paths as well as separate gain controls on all channels
• High-grade-sealed faders and potentiometers made by taiwan
• Insert option for external effects devices
• AUX Send and FX Send controls in the main section for optimal level adjustment
• Headphones output with dedicated volume control
• Built-in +48V phantom power for condenser mics.
• Extremely rugged construction ensures long life even under the most demanding conditions

INTRODUCTION

Congratulations! With the machine you have purchased a state-of-the art 7-channel mixing console that sets new standards. Our prime goal when develping the machine was to design a console that can be used for a great variety of applications. And to give you maximum flexibility. In combination with its comprehensive range of featrues and pro-level connections, the machine will be your perfect tool for any kind of application: broadcasting, video dubbing or giving the sound of your band its finishing touch.

Before you begin

Your machine was carefully packed in the factory and the packaging is designed to protect the unit from rough handing. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage, which may have occurred during transit.

If the unit is damaged, please do not return it to our company, but notify your dealer and the shipping company immediately, otherwise claims for damage or replacement may not be granted Shipping claims must be made by the consignee.

Be sure that there is enough space around the unit for cooling and please do not place the machine 2 on high-temperature devices such as radiators, etc. to avoid overheating.

Control elements

Interface panel

Microphone input

Balanced XLR socket to receive various balanced or unbalanced microphone signals.

1. pin = shielding ground 2 pins = signal + 3 pins = signal-

2. Phantom power switch

3. Recording output
   It is a stereo sound output signal socket, which is connected with the recording input part of the recorder to record the output signal of the mixer.

4. Stereo input Balanced 1/4 jack interface for input of left and right balance signals of stereo

5. Left/right channel total output balance interface

6. Gain control

7. Treble adjustment

8. Bass adjustment

9. Effect switch

10. Channel control and regulation

11. USB interface

12. MP3 play control area

13. Delay time adjustment

14. Effect feedback level adjustment

15. Monitor headphone output

16. Main signal output control push.

17. Monitor headphone volume adjustment

18. DC 5V interface

19. PC connection

WIRING

Fig. 2.1: Various connector types

Fig. 2.2: Wiring diagram of insert cable and headphones plug

WARRANTY

WARRANTY CARD/ONLINE REGISTRATION

To be protected by the extended warranty, the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to our company Spezielle Studiotechnik GmbH, in accordance with the conditions stipulated in 3. Failure to retum the card in due time (date as per postmark) will void any extended warranty claims.

WARRANTY

1.  warrants the mechanical and electronic components of this product to be free of defects in material and wordsmanship for a period of one (1) year from the original date of purchase, in accordance with the warranty regulations described below. If the product shows any defects within the specified warranty period that are not due to normal wear and tear and/or improper bandling by the user, out company shall, at its sole discretion, either repair or replace the product.
2. If the warranty claim proves to be justified, the product will be returned to the user freight prepaid.
3. Warranty claims other than those indicated above are expressly excluded.

WARRANTY REGULATIONS

1. Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealers invoice. Any product deemed eligible for repair or replacement by BEHRINGER under the terms of this warranty will be repaired or replaced within 30 days of receipt of the product at our company.

2. If the product needs to be modifled or adapted in order to comply with applicable technical or safety standards on a national or local level, in ant country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or worimanship. The warranty does not cover any such modification/adaptation, irrespective of whether it was carried out properly or not. Under the terms of this warranty, our company shall not be held responsible for any cost resulting from suck amodification/adaptation.

3. free inspections and maintenance/repair work are expressly excluded from this warranty, in particu lar, if caused by improper handling of the product by the user.
   This also applies to defects caused by normal wear and tear, in particular, or faders potentiometers keys/buttons and similar parts.

4. Damages/defects caused by the following conditions are not covered by this warranty:

   • misuse, neglect or failure to operate the unit in compliance with the instructions given in our company user or service manuals.
   • connection or operation of the unit in ant way that does not comply with the technical or safety regulations applicable in the country where the product is used.
   • damages/defects caused by force majeure or any other condition that is beyond the control of our company.

5. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the warranty.

6. If an inspection of the product by our company shows that the defect in question is not covered by the warranty, the inspection costs are payable by the customer.

7. Products thich do not meet the terms of this warranty will be repaired exclusively at the buyer s expense. our company will inform the buyer of any such circumstance. If the buyer fails to submit a written. repair order within 6 weeks after notification, our company will return the unit C. O. D. with a separate invoice for freight and packing. Such costs will also be invoiceded separately when the buyer has sent in a written repair order.

OTHER WARRANTY RIGHTS AND NATIONAL LAW

1. This warranty does not exclude or limit rhe buyer s statutory rights provided by national law, in partcular, any such rights against the seller that arise from a legally effective purchase contract.
2. The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law.

SPECIFICATIONS

INPUT CHANNELS 1 through 5

Mic input: electronically balanced, discrete input
Frequency response: configuration
Gain range: 10 Hz to 200 kHz
SNR: +14 dB to +60 dB
Line input: 120 dB E. I. N.
Frequency response: electronically balanced
Gain range: 10 Hz to 130 kHz
SNR: -6 dB to +38 dB
95 dB E. I. N.

STEREO CHANNELS

Frequency response: 10 Hz to 70 kHz
Gain range: Line:-8 to +15 dB / Mic: +13 to +60 dB
SNR: Line:90 dB / Mic: 104 dB E. I. N.

EQUSLIZATION

LOW: 50 Hz, +/- 15 dB
MID: 700 Hz, +/- 15 dB
HI: 10 kHz, +/-15dB

MAIN MIX

Main Outputs: +28 dBu balanced / +22 dBu unbalanced
AUX Send: +22 dBu unbalanced
EFF Send: +22 dBu unbalanced
Tape Out: +22 dBu unbalanced
Phones Output: +15 dBu 150

PHYSICAL

USA/Canada 120 V~, 60 Hz,
U. K./Australia 240 V~, 50 Hz,
Europe 230 V~, 50 Hz,
Japan 100 V~, 50 60 Hz,
China 200 V~, 50 60 Hz,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>