Tera HW0006 2D Barcode Scanner Wireless User Manual

Tera HW0006 2D Barcode Scanner Wireless

Symbologies

UPC-A

UPC-E

UPC-E to UPC-A

UPC-E1

UPC-E1 to UPC-A

Bookland EAN

EAN-8

EAN-13

UPC/EAN Addenda

ISBT 128

Code 128

Code 39

Code 39 Full ASCII

Code 32

Note: Code 32 Pharmaceutical is a variant of the Code 39 symbology. With Code 32 On, Code 39 reading accuracy will degrade. Code 32 Pharmaceuti­cal can only be read when Code 39 is enabled and no check digit is required.

Code 93

Codabar (NW-7)

GS1128

Interleaved 2 of 5

Discrete 2 of 5

Chinese 2 of 5

RSS-14

**Code 11

**

MSI

Code ID

Code ID Reference

• A= UPC-A, UPC-E, UPC-E1, EAN-8, EAN-13
• B = Code 39, Code 32
• C = Codabar
• D = Code 128, ISBT 128
• E = Code 93
• F = Interleaved 2 of 5
• G = Discrete 2 of 5
• J = MSI
• K = UCC/EAN-128
• L = Bookland EAN
• M = Trioptic Code 39
• N = Coupon Code
• R = RSS-14, RSS-Limited, RSS-Expanded

Scan Modes

Wireless Settings

Enter/Exit Programming Mode
You are able to change any settings by scanning configuration codes attached in this user manual. First, scan “Enter” symbol, then programming codes needed, finally, scan “Exit” symbol to save the settings.

Note: It is not necessary for scanners whose firmware version is above 1.18D to scan Enter/Exit symbols to set up the scanner.

Factory Default – Wireless
Scan the barcode below to reset the scanner to factory default settings for wireless connection.

Custom Defaults
By setting up custom defaults, you can save the settings which you use often as default settings for wireless connection. First, scan Enter symbol, then configuration codes needed, finally scan Exit symbol. The custom defaults will replace the original factory default settings. When the setting is done, the scanner won’t restore to factory defaults even if the factory default code is scanned.

Firmware Version

Beeper Volume

Battery Level

Sleep Timer

Character Encoding

Operation Modes

Real-time Mode

Storage Mode

Communications

USB-COM
Scan the following code to program the scanner to emulate a regular RS232-based COM Port. If you are using a Windows PC, you will need to install a driver. The driver will use the next available COM Port number. Please contact customer service for the driver.
Note: No extra configuration is necessary. The scanner can function as a USB serial port with both 2.4G USB dongle and USB cable connection.

2.4G Wireless
It functions the way a USB HID keyboard does.

2.4G Wireless Pairing
Receiver Pairing
The USB receiver is compatible with Win XP, Win?, Win8, Win10, macOS, etc.

• Step 1: Scan 2.4G Wireless symbol

Note: With 2.4G wireless pairing, the scanner will connect to the receiver which it has paired with the last time in preference.

• Step 2: Scan Pairing symbol.

• Step 3: Plug in the USB receiver. Wait for seconds till the scanner beeps, which indicates that pairing has succeeded.

Bluetooth Settings

(This feature is not available for Model HW0008L)

Bluetooth HID Pairing Instructions
When successfully connected, the scanner can input data into text field in the way a virtual keyboard does.

• Step 1: Scan “Bluetooth HID” barcode.

Note: The scanner prefers to connect to the receiver

• Step 2:
  Scan the “Pairing” barcode to get the scanner ready for pairing, with the LED indicator flashing blue.

• Step 3:
  Enable Bluetooth on your device and locate a device named “BarCode Scanner HID”.

• Step 4:
  Click/Tap the BarCode Scanner HID to pair your device with the scanner.

• Step 5:
  The scanner beeps once and the indicator turns into solid blue, indicating that the pairing has succeeded.

Note:
When the scanner is ready for pairing, a double press on the trigger or not detecting any pairing request within 1 minute will cause the scanner to exit pairing
Bluetooth SPP Pairing Instructions (Not available for iOS)
This connection mode only works with application designed for SPP purpose. If you are not familiar with Bluetooth SPP, please use Bluetooth HID.

• Step 1: Scan “Bluetooth SPP” symbol.
  You need to launch a specifically designed application (can be downloaded from application store) to get the scanner paired with your device via Bluetooth SPP.

• Step 2: Locate a device named “BarCode Scanner SPP” in the application.

• Step 3: Tap/click “BarCode Scanner SPP” to pair it with your device.

• Step 4: The scanner beeps once and the LED turns to solid blue, indicating the pairing has succeeded.

Bluetooth BLE Pairing Instructions
This connection mode only works with application designed for BLE purpose. If you are not familiar with Bluetooth BLE, please use Bluetooth HID.

• Step 1: Scan “Bluetooth BLE” symbol.
  You need to launch a specifically designed application (can be downloaded from application store) to get the scanner paired with your device
  via Bluetooth BLE.

• Step 2: Locate a device named “BarCode Scanner BLE” in the application.

• Step 3: Tap/click “BarCode Scanner BLE” to pair it with your device.

• Step 4: The scanner beeps once and the LED turns into solid blue, indicating that the pairing has succeeded.

Bluetooth HID Settings
Hold the trigger for 8s to get the scanner ready for Bluetooth HID pairing.

Virtual HID Keyboard Settings for iOS

Note: If you are using an Android device and the onscreen keyboard gets disabled whenever the scanner is connected with your device, please contact your device manufacturer for help. (Due to Android system limits, Android devices will disable the onscreen keyboard when they are connected with a barcode scanner.)

Bluetooth HID Transfer Rate
If the transmitted data gets lost or garbled, try to reduce the transfer rate.

Change Bluetooth Name

How to change the Bluetooth Name

• Step 1: Scan “Customize Bluetooth Name” symbol.

• Step 2: Scan target characters from the Character Chart in the appendix.

Note: The default name is Barcode Scanner. The target characters selected will be the new Bluetooth Name when the setting is done.

• The maximum configuration of Bluetooth Name is 16 characters. If inputted characters are more than 16 characters, the scanner picks up the first 16 characters as the new Bluetooth name.
• Construction of Bluetooth Name: Name+ Profile. Users can only modify the name but not the profile.

Check Bluetooth Name

Note: Only when the scanner is in Bluetooth HID/SP­P/BLE mode, can this barcode take effect.

Keyboard Country Layout
The scanner defaults to a US keyboard. To ensure that the scanner inputs scanned data correctly, the keyboard layout of the scanner should be aligned with that of host devices. To change the layout, scan the appropriate Keyboard Country barcode below.

Keyboard Conversion

Note: The settings are only valid in standard keyboard input mode and when inputting control characters with keyboard emulation.

Group Separator Replacement
This selection enables you to replace the hidden GS character with other printing character so that it can be displayed on host devices. If you don’t want it to be displayed, scan Customize Group Separator symbol then 1D symbol from ASCII character chart.

Custom GS Replacement

• Step 1 : Scan the barcode below. ****
• Step 2: Scan appropriate symbols from the Appendix ASCII Character Chart to replace the GS control character with the selected characters.

No GS Replacement

Prefix and Suffix Selections

The maximum size of a prefix or suffix configuration is 32 characters.

Add a Prefix

• Step 1 : Scan “Add Prefix”

• Step 2: Determine the appropriate value from the ASCII chart and scan the barcodes that represent the value accordingly in sequence.

Clear Prefixes

• Step 1: Scan “Add Prefix” symbol
• Step 2: Scan “Exit” symbol

A factory reset will clear prefixes as well.

Add a Suffix

• Step 1: Scan “Add Suffix”
• Step 2: Determine the appropriate value from the ASCII chart and scan the barcodes that represent the value accordingly in sequence.

Clear Suffixes

• Step 1: Scan “Add Suffix” symbol
• Step 2: Scan “Exit” symbol

A factory reset will clear suffixes as well.

Hide the First/Last Characters

The maximum size of a hiding configuration is 4 digits. This selection enables you to drop characters from the beginning or the end of the data.

• Step 1: Scan “Hide the first characters” or “Hide the last characters” symbol.

• Step 2: Scan appropriate symbols from the following codes.

Clear Character Hiding Settings
Step 1: Scan “Hide the First Characters” or “Hide the Last Characters” symbol.
Step 2: Scan “Exit” symbol.
A factory reset will clear the settings as well.

Terminators

Appendix – ASCII Character Chart

Note: The first 31 characters in the ASCII chart are non-printable characters, and the 32-127 characters are printable characters.

HWOOOSL

LED
Indicator| LED1, Flash Once| Normal Code – Read Successfully
LED2, Solid Blue| Connected
LED3, Solid Red| Charging
LED2, Flash Fast| Scanner is ready to pair up
Two LEDs flash slowly| Scanner is upgrading
Beeper| 1 long beep (Low to High)| Power up
1 long beep(High to Low)| Power off
1 short beep (Low Pitch)| Normal Code – Read Successfully/Pairing Succeeded
1 short beep (Low to High)| Barcodes have been stored in memory
1 short beep (High to Low)| Configuration Code – Read Successfully
3 short beeps (Low Pitch)| Transmission Failed/No Memory Available
5 short beeps (Low Pitch)| Battery running low
2 short beeps (Low Pitch)| Disconnected
2 short beeps (High Pitch)| Configuration Failed

If you need any product support, please contact our customer service.

Important Notice:
Please attach your Amazon Order Number and Product Model Number in the email.

Official Customer Service
Email Addresses:
service-us@tera-digital.com
service-eu@tera-digital.com
service-uk@tera-digital.com

Cell/WhatsApp (service in English):
+86 13382526580
If you want to learn more about our brand or need a digital user manual of the latest version, please visit our official website via the links below or by scanning the given

QR code:
https://tera-digital.com/
https://tera-digital.com/pages/user-manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>