tp-link Tapo T300 Smart Water Leak Sensor User Guide
- June 11, 2024
- tp-link
Table of Contents
- tp-link Tapo T300 Smart Water Leak Sensor
- Product Information
- Product Usage Instructions
- Appearance
- Power Up Your Sensor
- Check Your Sensor
- Set Up Your Sensor on the Tapo App
- Test Your Sensor
- Place Your Sensor
- How to Replace Battery
- Safety Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
tp-link Tapo T300 Smart Water Leak Sensor
Product Information
The Smart Water Leak Sensor is a device designed to monitor water leaks and alert users in case of any leaks. The device has a control button, LED indicator, sensor probe, buzzer, and battery compartment. The sensor has an operating temperature range of 0 (32) – 40 (105) and operates on a frequency range of 863~865MHz/863.35MHz / 25mW (e.r.p) 863~865MHz / 864.35MHz / 25mW (e.r.p) 868~868.6MHz / 868.35MHz / 25mW (e.r.p).
Product Usage Instructions
- Power Up Your Sensor: Remove the battery insulation tab to power up your sensor. The LED should blink.
- Check Your Sensor: The sensor will alarm if you drip water on the sensor probe or place it on a wet surface.
- Set Up Your Sensor on the Tapo App: A Tapo Hub is required. Make sure your Tapo Hub’s firmware is updated to the latest version and successfully set up via the Tapo app. Open the Tap the app and tap the button. Select Sensors and then your model. Follow the app instructions to complete the setup.
- Test Your Sensor: After setup, single press the control button on your sensor and check if the hub sounds an alarm.
- Place Your Sensor: Lay the sensor flat to monitor water leaks.
- How to Replace Battery:
- Remove the two screws securing the batteries and remove the back cover.
- Replace with the new batteries (AAA/LR03).
It is important to note that the device should be kept away from fire or hot environments and should not be ingested. The device should not be disassembled, repaired, or modified. If service is needed, contact the manufacturer. The user should read and follow all safety information when operating the device. The manufacturer cannot guarantee that no accidents or damage will occur due to improper use of the device.
Appearance
Control Button
LED Indicator
| Blinking | Enter pairing mode |
|---|---|
| Blinks once | Adjusted alarm volume level to Mute |
| Blinks twice | Adjusted alarm volume level to Low |
| Blinks 3 times | Adjusted alarm volume level to Normal |
| Blinks 4 times | Adjusted alarm volume level to High |
Power Up Your Sensor
Remove the battery insulation tab to power up your sensor. The LED should blink.
Check Your Sensor
The sensor will alarm if you drip water on the sensor probe or place it on a wet surface.
Set Up Your Sensor on the Tapo App
- A Tapo Hub is required. Make sure your Tapo Hub’s firmware is updated to the latest version and successfully set up via the Tapo app.
- Open the Tapo app and tap the + button. Select Sensors and then your model. Follow the app instructions to complete the setup.
Test Your Sensor
After setup, single press the control button on your sensor and check if the hub sounds an alarm.
Place Your Sensor
Lay the sensor flat to monitor water leaks.
How to Replace Battery
- Remove the two screws securing the batteries and remove the back cover.
- Replace with the new batteries (AAA/LR03).
Need some help?
Visit www.tapo.com/support/ for technical
support, user guides, FAQs, warranty & more
Warning
Risk of explosion if the battery is replaced by an incorrect type.
Warning
- Avoid replacement of a battery with an incorrect type that can defeat a safeguard.
- Avoid disposal of a battery in a fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Do not leave a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; Do not leave a battery subjected to the extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- Operating Temperature: 0℃ (32℉) – 40℃ (105℉)
Do not ingest battery, Chemical Burn Hazard
Safety Information
Keep the device away from fire or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU, and (EU) 2015/863.
The original EU declaration of conformity may be found at https://www.tapo.com/en/support/ce/ TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tapo.com/support/ukca/.
For EU/UK Region:
Operating Frequency/Nominal Operating Frequency
Max Output Power:
- 863~865MHz/863.35MHz/25mW (e.r.p)
- 863~865MHz/864.35MHz/25mW (e.r.p)
- 868~868.6MHz/868.35MHz/25mW (e.r.p)
©2023 TP-Link.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>