DEWALT DCB094 USB Charger Instruction Manual

DEWALT DCB094 USB Charger Instruction Manual

Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most reliable partners for professional power tool users.

Technical Data

Input| |
---|---|---
Battery| VDC| 18
USB Type C| VDC| 5‑15V @3A and 20V @5A
Output| |
USB Type A| VDC| 5, 2.4A
USB Type C| VDC| 5‑15V @3A and 20V @5A
Battery Port| VDC| 18, 6A
Type| | 1
USB charging port| | Type A, Type C
Battery type| | Li‑Ion
Battery Voltage| | 18
Weight| kg| 0.11
Power Adapter| |
Voltage| VAC| 100–240
Input AC frequency| Hz| 50/60
Model| | 2AEL1005
Power output (max)| W| 100
Output voltage, current| VDC, A| 5V,3A / 9V, 3A / 12V,3A, 15V,3A / 20V,5A
Average active efficiency| %| 84.8
Efficiency at low load (10%)| %| 76.75
No‑load power consumption| W| 0.086
Batteries| **DCB094*
---|---
** Cat #| VDC| Ah| Weight (kg)| Chargers/Charge Times (Minutes)
DCB546| 18/54| 6.0/2.0| 1.08| 75
DCB547/G| 18/54| 9.0/3.0| 1.46| 110
DCB548| 18/54| 12.0/4.0| 1.46| 150
DCB549| 18/54| 15.0/5.0| 2.12| 190
DCB181| 18| 1.5| 0.35| 20
DCB182| 18| 4.0| 0.61| 50
DCB183/B/G| 18| 2.0| 0.40| 30
DCB184/B/G| 18| 5.0| 0.62| 65
DCB185| 18| 1.3| 0.35| 20
DCB187| 18| 3.0| 0.54| 40
DCB189| 18| 4.0| 0.54| 50
DCBP034/G| 18| 1.7| 0.32| 22
DCBP518/G| 18| 5.0| 0.75| 65

*Battery charge times matrix provided for guidance only; charge times will vary depending on temperature and condition of batteries.

WARNING: To reduce the risk of injury, read the instruction manual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.

WARNING: This manual contains important safety and operating instructions for this DCB094 DeWALT USB charger. Before using the DCB094 DeWALT USB charger, read this manual and all labels on the DCB094 DeWALT USB charger, battery pack, charger and product(s) using the power source.

• Before using the DCB094 DeWALT USB charger, read all instructions and cautionary markings on the DCB094 DeWALT USB charger, battery pack and product using the battery pack.

• Shock hazard. Do not allow any liquid to get inside the DCB094 DeWALT USB charger. Electric shock may result.

• Burn hazard. To reduce the risk of injury, use only DeWALT 18 V lithium ion battery packs with the DCB094 DeWALT USB charger. Do not attempt to use it on any other battery packs. Other types of batteries may overheat and burst resulting in personal injury and property damage.

• This DCB094 DeWALT USB charger is not intended for any uses other than supplying power/charging small USB electronics. Any other uses may result in risk of fire, electric shock or electrocution.

• Do not expose the DCB094 DeWALT USB charger to rain or snow.

• When operating the DCB094 DeWALT USB charger outdoors, always provide a dry location.

• Do not operate the DCB094 DeWALT USB charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorized service center.

• Do not disassemble the DCB094 DeWALT USB charger, there are no user erviceable parts.
  • Do not operate the DeWALT USB charger with a damaged power adapter or USB cable.

• Do not force the power adapter or USB cable into the DeWALT USB charger’s USB port.

Chargers

DeWALT chargers require no adjustment and are designed to be as easy as possible to operate

Using an Extension Cable
An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (see Technical Data). The minimum conductor size is 1 mm2 ; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for compatible battery chargers (refer to Technical Data).

• Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.
  WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.
  WARNING: We recommend the use of a residual current device with a residual current rating of 30mA or less.
  CAUTION: Burn hazard. To reduce the risk of injury, charge only DeWALT rechargeable batteries. Other types of batteries may burst causing personal injury and damage.

•   CAUTION: Children should be supervised to ensure that they do not play with the appliance.
  NOTICE: Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any chargers other than DeWALT. DeWALT chargers and battery packs are specifically designed to work together.

• The intended uses of the DeWALT DCB094 are to charge DeWALT rechargeable batteries, and to charge or provide power to USB powered devices. Any other uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

• D o not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire,electric shock, or electrocution.

• Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug —have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorised service centre.

• Do not disassemble charger; take it to an authorised service centre when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

• In case of damaged power supply cord, the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent any hazard.

• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

Charging a Battery (Fig. A)

NOTE: To ensure maximum performance and life of lithium‑ion battery packs, charge the battery pack fully before first use.

1. Plug power adapter 7 into an appropriate outlet. For fastest charge rate, use the provided DeWALT power adapter.
   NOTE: Slower charging blink pattern may occur if using lower power adapters.

2. Attach the USB charger 3 to the battery pack 1 , making sure it is fully seated.
   NOTE: Once the USB charger is inserted the user will see the red LED illuminate for two seconds indicating the power‑up sequence.

3. Connect the power adapter 7 USB port to the USB charger 3 Type‑C USB port using either the provided USB cable 6 (for fastest charge rate) or a user supplied cable.

4. The Stage 1 Charging blink indicator represents the charge process that charges approximately 80% of the battery’s capacity. Stage 2 Charging blink indicator represents the remainder, or top off charge process, for the battery to reach full capacity.

5. The completion of charge will be indicated by both LEDs remaining ON continuously. The battery pack is fully charged and may be removed and used at this time or left in the DeWALT USB charger.

The DeWALT USB charger will not charge a faulty battery pack. The charger refusing to light could indicate a problem with the charger or a faulty battery pack.
NOTE: If the charger refuses to light, take the charger and battery pack to be tested at an authorized service center.

Charger Operation
Refer to the indicators below for the charge status of the battery pack.

Indicators

Stage 1 Charging
Stage 2 Charging
Fully Charged
Hot/Cold Pack Delay*

*The red light will continue to blink, but a yellow indicator light will be illuminated during this operation. Once the battery pack has reached an appropriate temperature, the yellow light will turn off and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty battery by refusing to light.

NOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery pack to be tested at an authorised service centre.

Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery pack life.
During hot/cold pack delay, the red LED will blink and the yellow LED will remain solid.
Once the battery pack has reached an appropriate temperature, the yellow light will turn off and the charger will resume the charging procedure.
A cold battery pack may charge at a slower rate than a warm battery pack.
Never operate the USB charger the if ventilation slots are blocked. Do not permit foreign objects to enter the interior of the USB charger.

Electronic Protection System
XR Li‑Ion tools are designed with an Electronic Protection System that will protect the battery pack against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection System engages. If this occurs, place the lithium‑ion battery pack on the charger until it is fully charged.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the power adapter from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non‑metallic brush. Do not use water or any cleaning solutions.
Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Battery Packs

Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include catalogue number and voltage.
The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.
• Never force battery pack into charger. Do not modify battery pack in any way to fit into a non‑compatible charger as battery pack may rupture causing serious personal injury.
• Charge the battery packs only in DeWALT chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations where the temperature may fall below 4 ˚C (39.2 ˚F) (such as outside sheds or metal buildings in winter), or reach or exceed 40 ˚C (104 ˚F) (such as outside sheds or metal buildings in summer).
• Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium‑ion battery packs are burned.
• If battery contents come into contact with the skin, immediately wash area withmild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to service centre for recycling.
WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool  boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.
CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.

Transportation

WARNING: Fire hazard. Transporting batteries can possibly cause fire if the battery terminals inadvertently come in contact with conductive materials. When transporting batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.
NOTE: Lithium‑ion batteries should not be put in checked baggage.

DeWALT batteries comply with all applicable shipping regulations as prescribed by industry and legal standards which include UN Recommendations on the Transport of Dangerous Goods; International Air Transport Association (IATA) Dangerous Goods Regulations, International Maritime Dangerous Goods (IMDG) Regulations, and the European Agreement Concerning The International Carriage of Dangerous Goods by Road (ADR). Lithium‑ion cells and batteries have been tested to section 38.3 of the UN Recommendations on the Transport of Dangerous Goods Manual of Tests and Criteria.
In most instances, shipping a DeWALT battery pack will be excepted from being classified as a fully regulated Class 9 Hazardous Material. In general, only shipments containing a lithium‑ion battery with an energy rating greater than 100 Watt Hours (Wh) will require being shipped as fully regulated Class 9. All lithium‑ion batteries have the Watt Hour rating marked on the pack. Furthermore, due to regulation complexities, DeWALT does not recommend air shipping lithium‑ion battery packs alone regardless of Watt Hour rating. Shipments of tools with batteries (combo kits) can be air shipped as excepted if the Watt Hour rating of the battery pack is no greater than 100 Wh.
Regardless of whether a shipment is considered excepted or fully regulated, it is the shipper’s responsibility to consult the latest regulations for packaging, labeling/marking and documentation requirements.

The information provided in this section of the manual is provided in good faith and believed to be accurate at the time the document was created. However, no warranty, expressed or implied, is given. It is the buyer’s responsibility to ensure that its activities comply with the applicable regulations.

Transporting the FLEXVOLTTM Battery
The DeWALT FLEXVOLTTM battery has two modes: Use and Transport.
Use Mode: When the FLEXVOLTTM battery stands alone or is in a DeWALT 18V product, it will operate as an 18V battery. When the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries) product, it will operate as a 54V battery.
Transport Mode: When the cap is attached to the FLEXVOLTTM battery, the battery is in Transport mode. Keep the cap for shipping.
When in Transport mode, strings of cells are electrically disconnected within the pack resulting in 3 batteries with a lower Watt hour (Wh) rating as compared to 1 battery with a higher Watt hour rating. This increased quantity of 3 batteries with the lower Watt hour rating can exempt the pack from certain shipping regulations that are imposed upon the higher Watt hour batteries.
For example, the Transport Wh rating might indicate 3 x 36 Wh, meaning 3 batteries of 36 Wh each. The Use Wh rating might indicate 108 Wh (1 battery implied).

Example of Use and Transport Label Marking

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.
2. For long storage, it is recommended to store a fully charged battery pack in a cool, dry place out of the charger for optimal results.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use.

Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the charger and the battery pack may show the following pictographs:

Read instruction manual before use.

See Technical Data for charging time.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Do not expose to water

Have defective cords replaced immediately

Charge only between 4 ˚C and 40 ˚C.

Only for indoor use.

Discard the battery pack with due care for the environment.

Charge DeWALT battery packs only with designated DeWALT chargers. Charging battery packs other than the designated DeWALT batteries with a DeWALT charger may make them burst or lead to other dangerous situations.

Do not incinerate the battery pack.

USE (without transport cap). Example: Wh rating indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built‑in transport cap). Example: Wh rating indicates 3 x 36 Wh (3 batteries of 36 Wh).

Battery Type
The DCB094 operates on 18 V Li‑Ion volt battery packs.
These battery packs may be used: DCB181, DCB182, DCB183, DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185, DCB187, DCB189, DCB546, DCB547, DCB547G, DCB548, DCB549, DCBP034, DCBP034G, DCBP518, DCBP518G. Refer to Technical Data for more information.

Package Contents

The package contains:

• 1 DeWALT USB charger
• 1 USB power delivery cable
• 1 Power adapter
• 1 Instruction manual
• 1 Battery pack (included in battery starter kit only)

NOTE: Battery packs, chargers and kit boxes are not included with N models. Battery packs and chargers are not included with NT models. B models include Bluetooth® battery packs.
NOTE: The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth®, SIG, Inc. and any use of such marks by DeWALT is under license. Other trademarks and trade names are those of their respective owners

• Check for damage to the tool, parts or accessories which may have occurred during transport.
• Take the time to thoroughly read and understand this manual prior to operation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Date Code Position (Fig. B)
The date code 9 , which also includes the year of manufacture, is printed into the housing. Example:

2022 XX XX
Year and Week of Manufacture

Description (Fig. A)

WARNING: Never modify the DCB094 USB charger or any part of it. Damage or personal injury could result.

1. Battery pack
2. Battery release button
3. DeWALT USB charger
4. USB Type‑A port
5. USB Type‑C port
6. USB power delivery cable
7. Power adapter
8. Fuel gauge

Intended Use

The DCB094 DeWALT USB charger is equipped with a USB Type‑A charging port and a USB
Type‑C power delivery charging port and is designed to charge or supply power to USB
Type‑C compatible devices with the use of DeWALT 18 V XR battery packs. Consult the chart in this manual for compatibility of chargers and battery packs.
DO NOT use under wet conditions or in the presence of flammable liquids or gases. The USB charger is for professional applications.
DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

• Young children and the infirm. This appliance is not intended for use by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and applicable regulations.
WARNING: T o reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start‑up can cause injury.

Installing and Removing the Battery Pack (Fig. B)

NOTE: For best results, make sure your battery pack is fully charged.
IMPORTANT: To avoid battery charge depletion, remove the battery pack from the DeWALT USB charger when not in use.

Over‑Discharge Protection
Over‑discharge protection will completely shut down the USB charger and require the user to remove the battery pack for at least 5 seconds and re‑insert into the DeWALT USB charger to use again. The user should ensure they see the power‑up blink pattern upon insertion to ensure proper operation.

To Install Battery Pack
Slide the battery pack 1 into the DeWALT USB charger 3 until the battery pack is firmly seated.

WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed battery terminals.

To Remove the Battery Pack
Press the battery release button 2 and pull the USB charger from the battery.

USB Charging Ports (Fig. A)
The DeWALT USB charger 3 is equipped with a USB Type‑A port 4 and a bi‑directional USB Type‑C Port 5 .

Type‑C port supports : Source – Power Delivery 3.0, Qualcomm*** QC3.0/2.0, Samsung™
AFC, BC 1.2, Type C only

• Sink – BC 1.2, Apple**** charging, PD 3.0, Type C only
• USB Type C can sink or source up to 100W

Type‑A port supports: BC1.2 and Apple FastCharge and Samsung™ FastCharge (AFC). Output only. USB Type‑A port capable of 12W

NOTE: Do not plug in devices that exceed the output ratings on the power source’s label. Doing so will shorten the USB charger’s useful life. DeWALT batteries will charge, via the USB Type C port from most USB power supplies. Some power supplies may require a different cable not supplied with this kit, and may charge at a slower rate

Charging a Device
Insert a USB plug into the USB Type‑A port 4 or bi‑directional USB Type‑C port 5 to supply power or charge your devices.

NOTE: There will be no LED indication while supplying power to or charging user devices. LEDs will only illuminate when charging DeWALT batteries.

NOTE: The USB ports will shut down and the yellow LED will blink if the battery pack temperture is out of acceptable range.

*Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
**Apple is a trademark of Apple Inc.

Belt Clip ( Fig. C)
WARNING : To reduce the risk of serious personal injury, ensure the screw holding the belt hook is secure.

IMPORTANT: When attaching or replacing the belt hook 10 , to the DeWALT USB charger, use only the screw 11 that is provided. Be sure to securely tighten screw. If the hook is not desired at all, it can be removed from the DeWALT USB charger. To remove the belt hook, remove the screw 11 that holds the belt hook in place.

MAINTENANCE
Your USB charger has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper care and regular cleaning.

WARNING: To reduce the risk of serious personal injury, disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start‑up can cause injury

The charger and battery pack are not serviceable.

Lubrication
Your USB charger requires no additional lubrication.

Cleaning
WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non‑metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the USB charger; never immerse any part of the tool into a liquid.

Optional Accessories

WARNING: Since accessories, other than those offered by DeWALT, have not been tested with this product, use of such accessories with this USB charger could be hazardous. To reduce the risk of injury, only DeWALT recommended accessories should be used with this product.

Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste. Products and batteries contain materials that can be recovered or recycled, reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com.

Rechargeable Battery Pack

This long‑life battery pack must be recharged when it fails to produce sufficient power on jobs that were easily done before. At the end of its technical life, discard it with due care for our environment:

• Run the battery pack down completely, then remove it from the tool.
• Li‑Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly

Belgique et Luxembourg België en Luxemburg| DEWALT ‑ Belgium BVBA Egide Walschaertsstraat 162800 Mechelen| Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:        32 15 47 37 99| www.dewalt.be enduser.BE@SBDinc.com
---|---|---|---
Danmark| DEWALT (Stanley Black&Decker AS) Roskildevej 222620 Albertslund| Tel: 70 20 15 10
Fax: 70 22 49 10| www.dewalt.dk kundeservice.dk@sbdinc.com
Deutschland| DEWALTRichard Klinger Str. 11 65510 Idstein| Tel: 06126‑21‑0Fax:       06126‑21‑2770| www.dewalt.de infodwge@sbdinc.com
Ελλάς| DEWALT (Ελλάς) Α.Ε.EΔΡΑ‑ΓΡΑΦΕΙΑ : Στράβωνος 7& Λ. Βουλιαγμένης, Γλυφάδα 166 74, ΑθήναSERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος| Τηλ:        00302108981616Φαξ:  00302108983570| www.dewalt.gr Greece.Service@sbdinc.com
España| DEWALT Ibérica, S.C.A.Parc de Negocios “Mas Blau”Edificio Muntadas, c/Bergadá, 1, Of. A6 08820 El Prat de Llobregat (Barcelona)| Tel:   934 797 400
Fax: 934 797 419| www.dewalt.es respuesta.postventa@sbdinc.com
France| DEWALT (Stanley Black & Decker France SAS) 62 Chemin de la Bruyère69570 Dardilly, France| Tel:04 72 20 39 20
Fax:04 72 20 39 00| www.dewalt.fr scufr@sbdinc.com
Schweiz Suisse Svizzera| DEWALTIn der Luberzen 42 8902 Urdorf| Tel: 044 ‑ 755 60 70
Fax:044 ‑ 730 70 67| www.dewalt.ch service@rofoag.ch
Ireland| DEWALTBuilding 4500, Kinsale Road Cork Airport Business Park Cork, Ireland| Tel: 00353‑2781800
Fax: 01278 1811| www.dewalt.ie sales.ireland@sbdinc.com
Italia| DEWALTvia Energypark 620871 Vimercate (MB), IT| Tel: 800‑01435339 039‑9590200
Fax: 39 039‑9590311| www.dewalt.it
Nederlands| DEWALTNetherlands BVPostbus 83,6120 AB BORN| Tel: 31 164 283 063
Fax: 31 164 283 200| www.dewalt.nl
Norge| DEWALTPostboks 46130405 Oslo, Norge| Tel: 45 25 13 00
Fax: 45 25 08 00| www.dewalt.no kundeservice.no@sbdinc.com
Österreich| DEWALTWerkzeug Vertriebsges m.b.H Oberlaaerstrasse 248, A‑1230 Wien| Tel: 01 ‑ 66116 ‑ 0
Fax: 01 ‑ 66116 ‑ 614| www.dewalt.at service.austria@sbdinc.com
Portugal| DEWALTEd. D Dinis, Quina da Fonte Rua dos Malhoes 2 2A 2º Esq.Oeiras e S. Juliao da Barra, paço de Arcos e Caxias 2770 071 Paço de Arcos| Tel: +351 214667500
Fax: +351214667580| www.dewalt.pt resposta.posvenda@sbdinc.com
Suomi| DEWALTPL4700521 Helsinki, Suomi| Puh: 010 400 4333
Faksi: 0800 411 340| www.dewalt.fi asiakaspalvelu.fi@sbdinc.com
Sverige| DEWALTBOX 94, 43122 Mölndal Sverige| Tel: 031 68 61 60Fax: 031 68 60 08| www.dewalt.se kundservice.se@sbdinc.com
Türkiye| Sanayi ve Ticareet Bakanlığı tebliğince kullanim ömrü 7 yıldır. Stanley Black & Decker Turkey Alet Üretim San. Tic. Ltd.Şti. AND Kozyataği ‑ İçerenköy Mah. Umut Sok.AND Ofis Sit. No: 10‑12 / 82‑83‑84 Ataşehir/İstanbul, Türkiye| Tel:+90 216 665 2900
Faks:   +90 216 665 2901| www.dewalt.com.tr info‑tr@sbdinc.com
United Kingdom| DEWALT, 270 Bath Road; Slough, Berks SL1 4DX| Tel:         01753‑567055Fax:       01753‑572112| www.dewalt.co.uk emeaservice@sbdinc.com
Australia| DEWALT810 Whitehorse Road Box Hill VIC 3128 Australia| Tel: Aust 1800 338 002Tel: NZ 0800 339 258| www.dewalt.com.au www.dewalt.co.nz
Middle East Africa| DEWALTP.O. Box ‑ 17164,Jebel Ali Free Zone (South), Dubai, UAE| Tel: 971 4 812 7400
Fax: 971 4 2822765| www.dewalt.ae support@dewalt.ae

References

• 2helpU
• Power Tools | Storage | Landscaping | DEWALT
• Elektrowerkzeuge | Aufbewahrung | Landschaftsbau | DEWALT Deutschland
• Elektrisch gereedschap | Opbergsystemen | Landscaping | DEWALT
• Elektrowerkzeuge | Aufbewahrung | Landschaftsbau | DEWALT
• Power Tools | Storage | Landscaping | DEWALT
• Power Tools | Storage | Landscaping | DEWALT
• Power Tools | Storage | Landscaping | DEWALT
• Elektrikli Aletleri | Depolama |Çevre Düzenleme | DEWALT
• Elektrowerkzeuge | Aufbewahrung | Landschaftsbau | DEWALT Deutschland
• Elværktøj | Opbevaring | Landskabspleje | DEWALT Denmark
• Herramientas Eléctricas | Almacenamiento | Jardinería | DEWALT España
• Sähkötyökalut | Säilytys | Maisemointi | DEWALT SUOMI
• Outils électroportatifs | Rangement | Jardin | DEWALT
• Ηλεκτρικά εργαλεία | Αποθήκευση | Διαμόρφωση τοπίου | DEWALT
• Power Tools | Storage | Landscaping | DEWALT
• Elettroutensili | Storage | Giardinaggio | DEWALT Italia
• Elektrisch gereedschap | Opbergsystemen | Landscaping | DEWALT
• Elektroverktøy | Oppbevaring | Landskapspleie | DEWALT Norge
• Ferramentas Elétricas | Armazenamento | Paisagismo | DEWALT PORTUGAL
• Elverktyg | Förvaring | Trädgårdsmaskiner | DEWALT Sverige

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>