PIXEL B0CFLNN5MH Wireless Lavalier Microphone User Manual
- June 14, 2024
- PIXEL
Table of Contents
VOICAL M
User manual
B0CFLNN5MH Wireless Lavalier Microphone
WARNING
- Do not use the product in the environment with high temperature and high humidity.
- It’s normal that the product may get hot while using it.
- Do not leave the product in a place where there are corrosive chemicals, or it will be corroded and damaged.
- There are sophisticated electronic circuits in this product. So please contact authorized personnel for maintenance. Any failures caused by unauthorized disassembly are not covered by the warranty.
- Please refer to the relevant national standard for use and operation. Any damage to the machine caused by improper use is not covered by the warranty, but paid maintenance.
- This user guidance is prepared based on the rigorous testing from this company. Further notice will not be given if the design and specifications change.
LIST OF ITEMS
PRODUCT VIEW
Wireless Receiver
-
Lightning Connector
For connecting mobile phones and tablets with lightning interface. -
Resetting Hole
-
LED Indicator
The pairing status is known by the LED indicators when the receiver is connected. -
USB-C Interface
It can charge cell phones and tablets with USB-C Connector.
Details are as below:
LED Indicator | Not paired/Pairing |
---|---|
Flashing | Receiver Status |
The indicator keeps on | Paired |
Wireless Transmitter
Transmitter Status | Operation | LED Indicator |
---|---|---|
Power On / Off | Microphone is out/into the charging case | Blue indicator |
flashes slowly
Not paired| /| Blue indicator flashes slowly
Paired, Acoustic mode| /| White indicator keeps on
Noise reduction mode| Double click the power switch in non-mute status;
double click again to go back to the acoustic mode| Blue indicator keeps on
Mute On/Off| Click the function button once| Red indicator keeps on
Pair up again| Long press the function button| Blue and red indicators flash
alternately
Low battery| /| Fast flashing in current mode (4 times/sec)
- When adjusting the noise reduction or acoustic mode of one transmitter, the other one will be synchronized with it, except for the mute mode.
Charging Case
-
Charging Interface
For charging the charging case through USB-C interface. -
Battery Indicator Button
Click the button, the battery of the charging case can be shown by the LED indicator. -
LED Indicator of the Charging Case
LED Indicator | Charging Case Battery Information |
---|---|
Flashing | Low battery |
Keeps on | Regular battery |
Flashing(when connected to the charging cable) | On charge |
Keeps on(when connected to the charging cable) | Fully Charged |
4. LED Indicator of the Charging Slot
LED Indicator| Battery Status of Charging case| LED Indicator|
Transmitter Status
---|---|---|---
Flashing| Low battery| Keeps on(Light off when
fully charged)| On charge
*When charging the charging case, the microphones inside are automatically charged, but the LED indicators of the charging slot for microphones are off by default at this time.
HOW TO USE
-
Wireless Transmitter Installation
a. Aim the top side of the transmitter at the sound source. It can be clipped on the collar or other places that close to the source.b. For outdoor or windy environments, a furrywindproof deadcat is recommended. -
External Microphone(Not Included in this package)
Open the dust plug and plug the external microphone directly into the 3.5mm socket. -
Wireless Receiver Installation
a. Plug the receiver into a phone or tablet that supports the connector. b. Mobile devices and tablets can be charged when plug the USB-C charging cable into the connector. (charging only) -
Paring
The transmitter and receiver are factory paired by default and can pair up again as the following steps:
a. Receiver: Press and hold the “Resetting Hole” for about 0.5 second with a toothpick, needle, etc. until the LED flashes, which indicates it’s reset successfully.
b. Transmitter: Long press the Function Button for about 2 seconds to pair up again.
c. The indicator of both receiver and transmitter are always on, which indicates they are paired successfully.
Note: The pairing process must be completed within 15 seconds, otherwise the above steps need to be repeated.
Transmitters will automatically shut down after 10 minutes without pairing. -
The Use of Charging Case
The receiver can be used without charging, while the transmitter should be placed in the charging slot for charging. The charging case can be charged by a USB-C connector on the right side.
SPECIFICATION
Name | 2.4GHz Wireless Microphone for Mobile Devices |
---|---|
Model | Voical M |
Pick-up Mode | Omnidirectional |
Working Frequency | 2300Mhz ~2380Mhz |
Reception Sensitivity | -93db |
Signal-to-Noise Ratio | 75db |
Transmit Frequency Bias | 20K |
Audio Response | 20Hz-20KHz |
Battery Capacity | 3.8V 280mAh× 2 |
Working Hours | 14h with full battery |
Charging Time | 3.5h |
Cell Phone/ Tablet Rated Charging Power | 5W |
Weight | RX : 6.6g(0.24oz) |
TX:22g(0.78oz) × 2
Size| RX:30 × 10× 55mm(1.2 × 0.4 × 2.2in)
TX: 21 × 21 × 71mm(0.8 × 0.8 × 2.8in)
Name| Charging Case
Battery Capacity| 2500mAh
Battery Duration| Charge the transmitters 3 times
Battery Voltage| 3.7V
Charging Connector| USB-C
Input Power| 5V/2A
Charging Time| 1h 40min
Size| 110 × 93 × 37mm(4.3 × 3.7 × 1.4in)
Weight| 136g(4.8oz)
Prolinx GmbH Brehmstr. 56, 40239 Duesseldorf Germany
Prolinx Global LTD 27 Old Gloucester Street London, WC1N 3AX, UKMfrs:
|
---|---
http://weixin.qq.com/r/gkPWzpXEeMgHrdGt9xaQ| https://www.pixelhk.com/cn
Dongguan Baoyi Electronic Technology Co., Ltd
Add: Building 2 No. 871, Dalang Section Guanzhang
Road, Dalang Town, Dongguan, China
E-mail: pixel@pixelhk.com
Support: support@pixelhk.com
User: retail@pixelhk.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>