LITHEAUDIO MP0128-03 Bluetooth 4 Inch Ceiling Speaker Installation Guide

LITHEAUDIO MP0128-03 Bluetooth 4 Inch Ceiling Speaker

Product Information

• Specifications
  • Model: [Insert Model Number]
  • Dimensions: [Insert Dimensions]
  • Weight: [Insert Weight]
  • Power Source: [Insert Power Source]
  • Warranty: [Insert Warranty Information]

Product Usage Instructions

• Unpacking and Setup
  • When you receive your product, carefully unpack all the components. Follow the included setup guide to assemble the product correctly.
• Powering On
  • Connect the product to a power source using the provided cable. Press the power button to turn on the device.
• Navigation and Settings
  • Use the navigation buttons or touchscreen to navigate through different settings and features. Refer to the user manual for detailed instructions on adjusting settings.
• Maintenance and Care
  • Regularly clean the product using a soft, damp cloth. Avoid using harsh chemicals that may damage the surface. Refer to the maintenance section in the user manual for specific care instructions.

FAQs

• Q: How do I reset the product to factory settings?
  • A: To reset the product to factory settings, navigate to the settings menu, select “Reset,” and confirm the action.
• Q: Can I use third-party accessories with this product?
  • A: We recommend using only approved accessories to ensure compatibility and safety. The use of third-party accessories may void the warranty.
• Q: What should I do if I encounter technical issues with the product?
  • A: If you experience technical issues, refer to the troubleshooting section in the user manual. If problems persist, contact our customer support for assistance.

SAFETY INSTRUCTIONS

• Please read the instructions carefully before installation and use. Keep the manual safe for future reference.
• Before installing the speakers into any ceiling/wall, check the structure for weight-bearing ability and avoid contact with any wiring or plumbing that might be behind the surface area. Installing on soft materials or in areas incapable of supporting the speakers’ weight may cause personal injury or damage to the speaker.
• Make sure the speaker is properly secured to the ceiling/wall. Please use the proper screws, bolts, or anchors. Failure to do so may cause the speaker to become unsecured and cause potential damages/injuries.
• Damage to the woofer and tweeter may occur if the speaker is dropped or resulting in no sound or distorted sound.
• Never overdrive your speakers to the point of distortion and always reduce volume before switching input sources.
• Use only approved and certified wiring in your installation, do not stretch or place the wire in contact with sharp objects.
• Before removing cables ensure all power to your speaker and other components is turned off.

PREPARATION

The hardware equipment listed below is needed to install the speaker.

PACKING LIST

Ensure that you have received all parts according to the component checklist before installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

INSTALLATION

1. Cut the Speaker Hole
   • Use a stud finder to locate an area that is free of obstructions or studs.
   • Position the cutout template where you are installing the speaker.
   • Trace the template to mark out the speaker location with a pencil.
   • Drill a pilot hole and cut all of the way around the circular outline with a cutting saw.

FCC

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Mobile RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>