Zgrmbo CR2032 LED Wall Mounted Clock Instruction Manual

CR2032 LED Wall Mounted Clock
Instruction Manual

CR2032 LED Wall Mounted Clock

Installation of Memory Battery

1. Plug in the DC 5V (inside of large cover on the back) and USB port for charging
2. Please remove the protective film before use.

General Operation

Under the time display mode

1. Press the ‘set’ button to switch time/calendar mode
2. Press the “+o-” to switch 12/24hr, press the “+button for 6 seconds can set the seconds flicker or not
3. Press DIMMER” button to adjust the brightness (5levels of brightness)
4.  Press ‘ALARM’ button(icon ), can turn on or off the alarm.

Time/ Calendar Set
Under the time display mode

1. Press the SET button for 3 seconds to enter DST setting, press’+ or- to turn on or off DST function,
2. Press the SET button again, into the ‘year’ setting, presswork’ -” to adjust the year,
3. Press the SET button again, into the ‘month’ setting, press’ +or’-” to adjust the month,
4. Press the SET button again, into the date’ setting, press+ or ­ to adjust the date;
5. Press the SET button again, into the hour’ setting, press’ + or to adjust the hour;
6. Press the SET button again, into the ‘ minute ‘setting, press + or to adjust the minute,
7. Press the SET button again to end the time setting and return time display

Note:
Please pay attention to whether the AM/PM setting is correct before setting the time, press the’ +”or “-“button to switch 12/24 hours system mode, In 12 hours mode, “AM” or” PM” will be displayed.
Alarm Setting
Under the time display mode

1. Press the ALARM ‘button (icon ) 3seconds to enter alarm setting, the ‘hour’ icon will flicker, press+or- to adjust the hour, for
2. Press the ALARM’ button again, the ‘minute’ icon will flicker, press ‘+or-‘to adjust the minute;
3. Press the ALARM’ button again to enter the alarm days setting, press +or’- to select the alarm mode,
4. Press the ‘ALARM’ button again to end the alarm setting and return time display 1-5two days off mode, alarm for Mon-Fri

1-6one day off mode, alarm for Mon-Sat
1-7daily mode, alarm for Mon-Sun under the time display mode,press ALARM button(icon ) can  turn on or off alarm.
Display Brightness Setting
Under the time display mode, press the “Brightness Setting” button(icon ) to adjust the brightness. (5 levels of brightness, the last level is to turn off the display.)

Night Brightness Setting
Under the time display mode, press “Brightness setting” button (icon ) for 3 seconds to enter night mode setting, press “Up” or “Down” button to turn night setting on or off, press “Brightness setting” button (icon ) again to end the setting and return to time display mode.
After the night mode is turned on, the clock displays high brightness between 07:00-19:00, medium brightness between 19:00-23:00, low brightness between 23:00-07:00. And daily automatic cycle brightness switching.
Note:
Even after the night mode is turned on, you can manually adjust the display brightness of the above three time zones to the appropriate brightness you want, and the clock will be automatically remembered as the default setting and automatically cycle the brightness to switch the brightness you set in these three time zones every day.

Additional Functions

• Seconds point flash and not flash conversion Under normal timekeeping mode, press the “+” button for 6 seconds to switch between seconds flash or not flash\
•  Display mode switch  Press the “-” button for 6 seconds to change between DP-1 (time only) and DP-2 (time 3 seconds and date 8 seconds alternate display ) during normal timekeeping

Warm Tips:
Please replace the cell button battery(CR2032) in time when the product has no memory function after power failure; If the system down, display abnormally, or the button is out of control, please press the reset button to reset the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>