AQUA CREST BB9-2 Outdoor Water Filter Installation Guide

AQUA CREST BB9-2 Outdoor Water Filter

Product Information

Specifications:

• Product: Outdoor Water Filter
• Filter Life: Up to 6,000 gallons

Installation Instructions:

1. Ensure the filter is installed in accordance with the manufacturer’s specifications and instructions.
2. Follow the installation procedures provided by the manufacturer.
3. Make sure to clean the filter before installation.
4. Replace the filter unit as recommended by the manufacturer (every [insert manufacturer’s recommended frequency]).

Cleaning Instructions:

1. Disconnect the filter unit from the water source.
2. Carefully remove the filter from its housing.
3. Rinse the filter under running water to remove any debris or contaminants.
4. Allow the filter to air dry completely before reinstalling it.

Warnings and Cautions:

Warning:
To reduce the risk of property damage due to water leakage, the filter MUST be installed in accordance with the manufacturer’s specifications and instructions. Failure to follow instructions and operating specifications will void your warranty. The manufacturer assumes no responsibility or liability for damage arising out of misuse of the product.

Caution:
This filter should not be used with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Frequently Asked Questions:

• Q: How can I contact Manufacturer Technical Support?
  A: You can reach Manufacturer Technical Support at 1-888-352-3558 (US) or via email at service@water-filter.com.

• Q: Where is the product manufactured?
  A: The product is made in China by V040 Qingdao Ecopure Filter Co., Ltd.

Filter life: up to 6,000 gallons.

Installation procedures

1. Wash hands before proceeding to ensure that contamination of filter system components does not take place during assembly.
2. Remove parts from their protective packaging, checking items against the contents list.
3. Prime filter purification elements. (See backside of system instruction sheet).
4. Place the large sealing washer over the threaded mount of the filter purification element.
5. Place the threaded mount stem into the hole in the interior base of the upper chamber.
6. Secure the element in the base of the chamber by screwing the wing nut onto the threaded mount. Repeat #3- #6 until all elements have been installed.

Cleaning instructions

1. Press the rubber priming button (tan or black colored) onto the stem of the filter purification element with the small end facing the element.
2. Place the stem of the filter element between your fingers and press the large end of the priming button against the faucet.
3. While holding the priming button against the faucet, turn on the cold water gently, allowing water to fill the cavity of the filter element.
4. Allow the exterior wall of the Black Berkey purification element to sweat beads of water for about 5 seconds.
5. Rinse process dust from the exterior of the purification element. The element has now been successfully primed. Repeat steps 1-5 for each additional element.

Caution:
This filter should not be used with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Warning

To reduce the risk of property damage due to water leakage, the filter MUST be installed in accordance with the manufacturer’s specifications and instructions. This filter unit must be replaced every gallon. Failure to follow instructions and operating specifications will void your warranty. What’s more, the manufacturer assumes no responsibility or liability for damage arising out of misuse of the product.

The service life mentioned above is subject to chlorine reduction. The actual result varies according to the local water quality.

Frequently asked questions

• Q: Must the filter be changed on a regular basis?
  A: Yes, over-used filters will degrade filtration performance. It’s important to change your filter regularly for the best filtration results. Users with hard water should increase the frequency of filter changes.

• Q: What is the shelf life of the filter?
  A: The shelf life of an unused, packaged filter is indefinite. Filters should be stored in a cool, dry place until you’re ready to use them.

• Q: Why are there black specks in the water?
  A: It’s normal for black carbon particles to appear on the outside of your filter. This happens when the filter is jarred in shipping. It’s safe. Flushing the filter before use will remove the carbon dust.

Manufacturer Technical Support

• Tel: 1-888-352-3558 (U.S.)
• E-mail: service@water-filter.com.

Made in China V040
Qingdao Ecopure Filter Co., Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>