WeeFancy VT018 Wireless Charging User Manual

WeeFancy VT018 Wireless Charging

Thanks for purchasing WeeFancy products. Please read this User Manual thoroughly before use of the product and retain it for future reference.

PRODUCT DIAGRAM

SPECIFICATIONS

• Model  VT018
• Battery Capacity  1200mAh/4.62Wh
• Type-C Input    5V-1.0A
• Wireless charging Output  2.5W
• Dimensions  144.55217.8mm
• Weight    40g

USING YOUR POWER BANK

Before First Use

• Please pay attention to the symbols and indicators for proper use.
• It is recommended to fully charge the unit with a standard charger before first use.

Using Your Power Bank

Check the battery level
Press the Wakeup Button to check the battery level.

Charging your power bank

1. Charging the power bank via USB C cable.
2. Before full charge till 100%, the indicator will keep flashing.

Note:

• The indicator will stop flashing till charging to 100%.
• The power bank not support charging though.

Charging your device

1. Connect your device to the power bank via the Type-C/USB output port.
2. Charging will start automatically.
3. Unplug the charging cable when charging has completed.

Note : QC/PD only works with a QC/PD cable and your device should support QC/PD protocol

Wakeup Button

1. Press the button to show the remaining battery percentage.
2. During charging, double press the button to cut off the output, press again to resume.

Warranty

• 12 Month Warranty.
• Life-time Support.

Note:   This warranty is void if the defect is caused by:

• Damage caused by force majeure.
• Accidental damage, misuse, abuse, neglect.
• Improper repair or alteration by unauthorized persons.
• Expired warranty period.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using this product, basic precautions should always be followed, including the following:

• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the product is used near children.
• Do not put fingers or hands into the product.
• Do not expose power bank to rain or snow.
• Use of a power supply or charger not recommended or sold by power pack manufacturer may result in a risk of fire or injury to persons.
• Do not use the power bank in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons.
• Do not use the power bank that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not disassemble the power bank. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
• Do not expose a power pack to fire or excessive temperature. Exposure to fire or temperature above 100°C may cause explosion. The temperature of 100°C can be replaced by the temperature of 212°F.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
• Switch off the power bank when not in use. Do not place or use this product in high temperature or damp environment. Do not expose it to the sun.
• Dispose the power bank according to the local statues environmental protection regulations.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC: ” before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>