DEWALT DCS389 60V MAX Brushless Cordless Reciprocating Saw Instruction Manual
- June 14, 2024
- Dewalt
Table of Contents
Instruction Manual
DEWALT DCS389 Cordless Reciprocating Sabre Saw
Congratulations!
You have chosen a DEWALT tool. Years of experience, thorough product
development and innovation make DEWALT one of the most reliable partners for
professional power tool users.
WARNING : The declared vibration and/or noise emission level represents
the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
and/or noise emission may differ. This may significantly increase the exposure
level over the total working period. An estimation of the level of exposure to
vibration and/or noise should also take into account the times when the tool
is switched off or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects
of vibration and/or noise such as: maintain the tool and the accessories, keep
the hands warm (relevant for vibration), organisation of work patterns.
EC-Declaration of Conformity
Cordless Reciprocating Sabre Saw DCS389
DEWALT declares that these products described under Technical Data are in compliance with: 2006/42/EC, EN62841-1:2015, EN62841-2-11:2016. These products also comply with Directive 2014/30/EU and 2011/65/EU. For more information, please contact DEWALT at the following address or refer to the back of the manual. The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
- DANGER : Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
- WARNING : Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
- CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
- NOTICE : Indicates a practice not related to personal injury which, if not avoided, may result in property damage. Denotes risk of electric shock. Denotes risk of fire.
Batteries | Chargers/Charge Times (Minutes) |
---|---|
Cat # VDC Ah Weight (kg) | DCB104 DCB107 DCB112 DCB113 |
DCB115 DCB116 DCB117 DCB118 DCB132 DCB119
DCB546| 18/54| 6.0/2.0| 1.05| 60| 270| 170| 140| 90| 80| 40| 60| 90| X
DCB547| 18/54| 9.0/3.0| 1.46| 75| 420| 270| 220| 135| 110| 60| 75| 135*| X
DCB548| 18/54| 12.0/4.0| 1.44| 120| 540| 350| 300| 180| 150| 80| 120| 180| X
GENERAL POWER TOOL SAFETY WARNINGS
WARNING : Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury. SAVE ALL WARNINGS AND INSTRUCTIONS. FOR FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains‑operated (corded)
power tool or battery‑operated (cordless) power tool.
-
Work Area Safety
1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. -
Electrical Safety
1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. -
Personal Safety
1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result 2. in serious personal injury.
3. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non‑skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
4. Prevent unintentional starting. Ensure the switch is in the off‑position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
5. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
6. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
7. Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
8. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust‑related hazards.
9. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second. -
Power Tool Use and Care
1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
8. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations. -
Battery Tool Use and Care
1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
3. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
5. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
7. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire. -
Service
1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
2. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Safety Instructions for Reciprocating Saws
- Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.
Additional Safety Instructions for Reciprocating Sabre Saws
- ALWAYS wear a dust mask. Exposure to dust particles can cause breathing difficulty and possible injury.
- Never switch on the tool when the saw blade is jammed in the workpiece or in contact with the material.
- Keep hands away from moving parts. Never place your hands near the cutting area.
- Use extra caution when cutting overhead and pay particular attention to overhead wires which may be hidden from view. Anticipate the path of falling branches and debris ahead of time.
- Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.
Switching On and Off
- After switching off, never attempt to stop the saw blade with your fingers.
- Never put the saw down on a table or work bench unless switched off. The saw blade will keep running briefly after the tool has been switched off.
When Sawing
- When using saw blades specially designed for cutting wood remove all nails and metal objects from the workpiece before starting work.
- Wherever possible, use clamps and vices to fasten the workpiece securely.
- Do not attempt to saw extremely small workpieces.
- Do not bend too far forward. Make sure that you always stand firmly, particularly on scaffolding and ladders.
- Always hold the saw with both hands.
- For cutting curves and pockets, use an adapted saw blade. Checking and Changing the Saw Blade
- Only use saw blades conforming to the specifications contained in these operating instructions.
- Only sharp saw blades in perfect working condition should be used; cracked or bent saw blades should be discarded and replaced at once.
- Ensure that the saw blade is securely fixed.
Residual Risks
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
- Impairment of hearing.
- Risk of personal injury due to flying particles.
- Risk of burns due to accessories becoming hot during operation.
- Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS.
Chargers
DEWALT chargers require no adjustment and are designed to be as easy as
possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only. Always check that
the battery pack voltage corresponds to the voltage on the rating plate. Also
make sure that the voltage of your charger corresponds to that of your mains.
iYour DEWALT charger is double insulated in accordance with EN60335; therefore
no earth wire is required. If the supply cord is damaged, it must be replaced
only by DEWALT or an authorised service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
- Safely dispose of the old plug.
- Connect the brown lead to the live terminal in the plug.
- Connect the blue lead to the neutral terminal. WARNING: No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary. Use an
approved extension cable suitable for the power input of your charger (see
Technical Data). The minimum conductor size is 1 mm2; the maximum length is 30
m. When using a cable reel, always unwind the cable completely.
Important Safety Instructions for All Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important safety and
operating instructions for compatible battery chargers (refer to Technical
Data).
- Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.
- WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.
- WARNING : We recommend the use of a residual current device with a residual current rating of 30mA or less.
- CAUTION : Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable batteries. Other types of batteries may burst causing personal injury and damage.
- CAUTION : Children should be supervised to ensure that they do not play with the appliance.
- NOTICE : Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.
- DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together.
- These chargers are not intended for any uses other than charging DEWALT rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.
- Do not expose charger to rain or snow.
- Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord.
- Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
- Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire,electric shock, or electrocution.
- Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
- Do not operate charger with damaged cord or plug— have them replaced immediately.
- Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorised service centre.
- Do not disassemble charger; take it to an authorised service centre when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
- In case of damaged power supply cord, the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent any hazard.
- Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
- NEVER attempt to connect two chargers together.
- The charger is designed to operate on standard 230V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.
Charging a Battery (Fig. B)
- Plug the charger into an appropriate outlet before inserting battery pack.
- Insert the battery pack 7 into the charger, making sure the battery pack is fully seated in the charger. The red (charging) light will blink repeatedly indicating that the charging process has started.
- The completion of charge will be indicated by the red light remaining ON continuously. The battery pack is fully charged and may be used at this time or left in the charger. To remove the battery pack from the charger, push the battery release button 8 on the battery pack.
NOTE : To ensure maximum performance and life of lithium-ion battery packs, charge the battery pack fully before first use.
Charger Operation
Refer to the indicators below for the charge status of the battery
pack.
The red light will continue to blink, but a yellow indicator light will be
illuminated during this operation. Once the battery pack has reached an
appropriate temperature, the yellow light will turn off and the charger will
resume the charging procedure. The compatible charger(s) will not charge a
faulty battery pack. The charger will indicate faulty battery by refusing to
light.
NOTE : This could also mean a problem with a charger. If the charger
indicates a problem, take the charger and battery pack to be tested at an
authorised service centre.
hot/cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it
automatically starts a Hot/Cold Pack Delay, suspending charging until the
battery pack has reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This feature ensures maximum
battery pack life.
A cold battery pack will charge at a slower rate than a warm battery pack. The
battery pack will charge at that slower rate throughout the entire charging
cycle and will not return to maximum charge rate even if the battery pack
warms. The DCB118 charger is equipped with an internal fan designed to cool
the battery pack. The fan will turn on automatically when the battery pack
needs to be cooled. Never operate the charger if the fan does not operate
properly or if ventilation slots are blocked. Do not permit foreign objects to
enter the interior of the charger.
Electronic Protection system
XR Li-Ion tools are designed with an Electronic Protection System that will
protect the battery pack against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection System
engages. If this occurs, place the lithium-ion battery pack on the charger
until it is fully charged.
Wall Mounting
These chargers are designed to be wall mountable or to sit upright on a
table or work surface. If wall mounting, locate the charger within reach of an
electrical outlet, and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template for the location of
the mounting screws on the wall. Mount the charger securely using drywall
screws (purchased separately) at least 25.4 mm long with a screw head diameter
of 7–9 mm, screwed into wood to an optimal depth leaving approximately 5.5 mm
of the screw exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
Charger Cleaning Instructions
WARNING : Shock hazard. Disconnect the charger from the AC outlet before
cleaning. Dirt and grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use water or any cleaning
solutions. Never let any liquid get inside the tool; never immerse any part of
the tool into a liquid.
Battery Packs
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include catalogue number
and voltage. The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions below. Then
follow charging procedures outlined.
READ ALL INSTRUCTIONS
- Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.
- Never force battery pack into charger. Do not modify battery pack in any way to fit into a non‑compatible charger as battery pack may rupture causing serious personal injury.
- Charge the battery packs only in DEWALT chargers.
- DO NOT splash or immerse in water or other liquids.
- Do not store or use the tool and battery pack in locations where the temperature may fall below 4 ˚C (34 ˚F) (such as outside sheds or metal buildings in winter), or reach or exceed 40 ˚C (104 ˚F) (such as outside sheds or metal buildings in summer).
- Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium‑ion battery packs are burned.
- If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.
- Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention.
WARNING : Burn hazard. Battery liquid may be flammable if exposed to
spark or flame.
WARNING : Never attempt to open the battery pack for any reason. If
battery pack case is cracked or damaged, do not insert into charger. Do not
crush, drop or damage
battery pack. Do not use a battery pack or charger that has received a sharp
blow, been dropped, run over or damaged in any way (i.e., pierced with a nail,
hit with a hammer, stepped on). Electric shock or electrocution may result.
Damaged battery packs should be returned to service centre for recycling.
WARNING : Fire hazard. Do not store or carry the battery pack so that
metal objects can contact exposed battery terminals. For example, do not place
the battery pack in aprons, pockets, tool boxes, product kit boxes, drawers,
etc., with loose nails, screws, keys, etc.
CAUTION : When not in use, place tool on its side on a stable surface
where it will not cause a tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack but may be easily knocked
over.
Transportation
WARNING : Fire hazard. Transporting batteries can possibly cause fire if
the battery terminals inadvertently come in contact with conductive materials.
When transporting batteries, make sure that the battery terminals are
protected and well insulated from materials that could contact them and cause
a short circuit.
NOTE : Lithium‑ion batteries should not be put in checked baggage.
DEWALT batteries comply with all applicable shipping regulations as prescribed
by industry and legal standards which include UN Recommendations on the
Transport of Dangerous Goods; International Air Transport Association (IATA)
Dangerous Goods Regulations, International Maritime Dangerous Goods (IMDG)
Regulations, and the European Agreement Concerning The International Carriage
of Dangerous Goods by Road (ADR). Lithium-ion cells and batteries have been
tested to section 38.3 of the UN Recommendations on the Transport of Dangerous
Goods Manual of Tests and Criteria.
In most instances, shipping a DEWALT battery pack will be excepted from being
classified as a fully regulated Class 9 Hazardous Material. In general, only
shipments containing a lithium-ion battery with an energy rating greater than
100 Watt Hours (Wh) will require being shipped as fully regulated Class 9. All
lithium-ion batteries have the Watt Hour rating marked on the pack.
Furthermore, due to regulation complexities, DEWALT does not recommend air
shipping lithium-ion battery packs alone regardless of Watt Hour rating.
Shipments of tools with batteries (combo kits) can be air shipped as excepted
if the Watt Hour rating of the battery pack is no greater than 100 Wh.
Regardless of whether a shipment is considered excepted or fully regulated, it
is the shipper’s responsibility to consult the latest regulations for
packaging, labeling/marking and documentation requirements. The information
provided in this section of the manual is provided in good faith and believed
to be accurate at the time the document was created. However, no warranty,
expressed or implied, is given. It is the buyer’s responsibility to ensure
that its activities comply with the applicable regulations.
Transporting the FLEXVOLTTM Battery
The DEWALT FLEXVOLTTM battery has two modes: Use and Transport.
-
Use Mode: When the FLEXVOLTTM battery stands alone or is in a DEWALT 18V product, it will operate as an 18V battery. When the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries) product, it will operate as a 54V battery. Transport Mode: When the cap is attached to the FLEXVOLTTM battery, the battery is in Transport mode. Keep the cap for shipping.
When in Transport mode, strings of cells are electrically disconnected within the pack resulting in 3 batteries with a lower Watt hour (Wh) rating as compared to 1 battery with a higher Watt hour rating. This increased quantity of 3 batteries with the lower Watt hour rating can exempt the pack from certain shipping regulations that are imposed upon the higher Watt hour batteries. -
For example, the Transport Wh rating might indicate 3 x 36 Wh, meaning 3 batteries of 36 Wh each. The Use Wh rating might indicate 108 Wh (1 battery implied).
Storage Recommendations
- The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.
- For long storage, it is recommended to store a fully charged battery pack in a cool, dry place out of the charger for optimal results.
Note : Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the charger
and the battery pack may show the following pictographs:
Battery Type
The following SKU(s) operate on a 54 volt battery pack: DCS389 These battery
packs may be used: DCB546, DCB547, DCB548. Refer to Technical Data for more
information.
Package Contents
The package contains:
- 1 Cordless reciprocating sabre saw
- 1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)
- 2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)
- 1 Charger
- 1 Instruction manual
- Check for damage to the tool, parts or accessories which may have occurred during transport.
- Take the time to thoroughly read and understand this manual prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Date Code Position (Fig. A)
The date code 10 , which also includes the year of manufacture, is printed
into the housing.
Example: 2020 XX XX Year of Manufacture
Description (Fig. A)
WARNING : Never modify the power tool or any part of it. Damage or personal injury could result.
- Trigger switch
- Lock-off button
- Blade clamp release lever
- Shoe
- Hand grip
- Main handle
- Battery pack
- Battery release button
- Worklight
Intended Use
Your DCS389 cordless reciprocating sabre saws have been designed for
professional sawing of wood, metal and tubes. The compact design permits
cutting extremely close to the edge of difficult areas.
- DO NOT use under wet conditions or in presence of flammable liquids or gases. These reciprocating saws are professional power tools.
- DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.
- Young children and the infirm. This appliance is not intended for use by young children or infirm persons without supervision.
- This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
- WARNING : To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start‑up can cause injury.
- WARNING : Use only DEWALT battery packs and chargers.
Inserting and Removing the Battery Pack from the Tool (Fig. B)
Note : Make sure your battery pack 7 is fully charged.
To Install the Battery Pack into the Tool Handle
- Align the battery pack 7 with the rails inside the tool’s handle (Fig. B).
- Slide it into the handle until the battery pack is firmly seated in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
- Press the release button 8 and firmly pull the battery pack out of the tool handle.
- Insert battery pack into the charger as described in the charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some DEWALT battery packs include a fuel gauge which consists of three green
LED lights that indicate the level of charge remaining in the battery pack. To
actuate the fuel gauge, press and hold the fuel gauge button 11 . A
combination of the three green LED lights will illuminate designating the
level of charge left. When the level of charge in the battery is below the
usable limit, the fuel gauge will not illuminate and the battery will need to
be recharged.
Note : The fuel gauge is only an indication of the charge left on the
battery pack. It does not indicate tool functionality and is subject to
variation based on product components, temperature and end-user application.
Blade Installation and Removal
(Fig. A, E–G) Different blade lengths are available. Use
the appropriate blade for the application. The blade should be longer than 90
mm and should extend past the shoe and the thickness of the workpiece during
the cut. Do not use jigsaw blades with this tool.
WARNING : Cut hazard. Blade breakage may occur if the blade does not
extend past the shoe and the workpiece during the cut (Fig. B). Increased risk
of personal injury, as well as damage to the shoe and workpiece may result.
To Install Blade into Saw
- Pull blade clamp release lever 3 up (Fig. C).
- Insert blade shank from the front.
- Push blade clamp release lever down.
NOTE : The blade can be installed in two positions as shown in Figure G.
To Remove Blade from Saw
CAUTION : Burn hazard. Do not touch the blade immediately after use. Contact with the blade may result in personal injury.
- Open up blade clamp release lever.
- Remove blade.
Instructions for Use
WARNING : Always observe the safety instructions and applicable
regulations.
WARNING : To reduce the risk of serious personal injury, turn tool off
and disconnect battery pack before making any adjustments or removing/
installing attachments or accessories. An accidental start‑up can cause
injury.
Proper Hand Position (Fig. D)
WARNING : To reduce the risk of serious personal injury, ALWAYS use
proper hand position as shown.
WARNING : To reduce the risk of serious personal injury, ALWAYS hold
securely in anticipation of a sudden reaction. Proper hand position requires
one hand on the hand grip 5 , with the other hand on the main handle 6.
Variable Speed Trigger Switch (Fig. C)
Lock-off Button and Trigger switch
Your saw is equipped with a lock-off button 2 . To lock the trigger switch,
press the lock-off button as shown in Figure C. Always lock the trigger switch
1 when carrying or storing the tool to eliminate unintentional starting. The
lock-off button is colored red to indicate when the switch is in its unlocked
position. To unlock the trigger switch, press the lock-off button as shown in
Figure C. Pull the trigger switch to turn the motor ON. Releasing the trigger
switch turns the motor OFF.
WARNING : This tool has no provision to lock the switch in the ON
position, and should never be locked ON by any other means. The variable speed
trigger switch will give you added versatility. The further the trigger is
depressed the higher the speed of the saw.
CAUTION : Use of very slow speed is recommended only for beginning a cut.
Prolonged use at very slow speed may damage your saw.
Worklight (Fig. A)
There is a worklight 9 located on the end of the tool near the shoe. The
worklight is activated when the trigger switch is depressed and will remain on
for a short time after the trigger switch is released. If the trigger switch
remains depressed, the worklight will remain on.
NOTE : The worklight is for lighting the immediate work surface and is
not intended to be used as a flashlight.
Battery Indicator
As the battery nears a fully discharged state, the flashlight will blink
twice and then the brightness of the light will drop below the normal level.
This cycle will repeat until the battery is fully discharged.
Cutting (Fig. H, I)
WARNING : Always use eye protection. All users and bystanders must wear
approved eye protection.
WARNING : Exercise extra caution when cutting towards operator. Always
hold saw firmly with both hands while cutting.
Before cutting any type of material, be sure it is firmly anchored or clamped
to prevent slipping. Place blade lightly against work to be cut, switch on saw
motor and allow it to obtain maximum speed before applying pressure. Whenever
possible, the saw shoe must be held firmly against the material being cut
(Fig. I). This will prevent the saw from jumping or vibrating and minimise
blade breakage. Any cuts that put pressure on the blade such as angle or
scroll cuts increase potential for vibration, kickback, and blade breakage.
WARNING : Use extra caution when cutting overhead and pay particular
attention to overhead wires that may be hidden from view. Anticipate the path
of falling branches and debris ahead of time.
WARNING : Inspect work site for hidden gas pipes, water pipes, or
electrical wires before making blind or plunge cuts. Failure to do so may
result in explosion, property damage, electric shock, and/or serious personal
injury.
Pocket/Plunge Cutting – Wood Only (Fig. H)
The initial step in pocket cutting is to measure the surface area to be cut
and mark clearly with a pencil, chalk or scriber. Use the appropriate blade
for the application. The blade should be longer than 90 mm and should extend
past the shoe and the thickness of the workpiece during the cut. Insert blade
in blade clamp.
Next, tip the saw backward until the back edge of the shoe is resting on the
work surface and the blade clears the work surface (position 1, Fig. H). Now
switch motor on, and allow saw to come up to speed. Grip saw firmly with both
hands and begin a slow, deliberate upward swing with the handle of the saw,
keeping the bottom of the shoe firmly in contact with the workpiece (position
2, Fig. H). Blade will begin to feed into material. Always be sure blade is
completely through material before continuing with pocket cut.
Note : In areas where blade visibility is limited, use the edge of the
saw shoe as a guide. Lines for any given cut should be extended beyond edge of
cut to be made.
Metal Cutting (Fig. I)
Your saw has different metal cutting capacities depending upon type of blade
used and the metal to be cut. Use a finer blade for ferrous metals and a
coarse blade for non ferrous materials. In thin gauge sheet metals it is best
to clamp wood to both sides of sheet. This will ensure a clean cut without
excess vibration or tearing of metal. Always remember not to force cutting
blade as this reduces blade life and causes costly blade breakage.
NOTE : It is generally recommended that when cutting metals you should
spread a thin film of oil or other lubricant along the line ahead of the saw
cut for easier operation and longer blade life.
MAINTENANCE
Your power tool has been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
WARNING : To reduce the risk of serious personal injury, turn tool off
and disconnect battery pack before making any adjustments or removing/
installing attachments or accessories. An accidental start‑up can cause
injury.
The charger and battery pack are not serviceable.
Lubrication: Your power tool requires no additional lubrication.
Cleaning
WARNING : Blow dirt and dust out of the main housing with dry air as
often as dirt is seen collecting in and around the air vents. Wear approved
eye protection and approved dust mask when performing this procedure.
WARNING : Never use solvents or other harsh chemicals for cleaning the
non‑metallic parts of the tool. These chemicals may weaken the materials used
in these parts. Use a cloth dampened only with water and mild soap. Never let
any liquid get inside the tool; never immerse any part of the tool into a
liquid.
Optional Accessories
WARNING : Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT-recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste. Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce
sufficient power on jobs which were easily done before. At the end of its
technical life, discard it with due care for our environment:
- Run the battery pack down completely, then remove it from the tool.
- Li-Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.
Read more: https://manuals.plus/dewalt/dcs389-cordless-reciprocating-sabre- saw-manual#ixzz8KGsPPe7o
References
- 2helpU
- Autorizovaný servis elektrického nářadí, půjčovna nářadí, prodejna nářadí
- Elektrické nářadí | Úložné systémy | Zahrada | DEWALT Česko
- Prodej a servis elektronářadà Krnov | K R E S spol. s r.o.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>