ELITE SCREENS UHD-B Series Aeon Cine White User Guide
- June 14, 2024
- ELITE SCREENS
Table of Contents
ELITE SCREENS UHD-B Series Aeon Cine White
Specifications
- Model : V2.1
- Screen Sizes : 92”, 100”, 110”, 120”, 125”, 135”, 150”, 180”, 200”
- Frame Parts : Main Frame Parts (vertical frame, edge trim parts)
- Hardware Parts : Center Joints, Elbow Joints, Side Cover Joints, Screws, Spring, Spring Hook, Wall Brackets, Wall Screws, Hollow Wall Anchors, Angle Cover, Center Support Bar, White Gloves, Iron Rods
Aeon Cine White® UHD-B Series
EDGE FREE® Matte White Fixed Frame Screen USER’S GUIDE – M Type
Product Description
- The Aeon Series is a fixed frame projection screen that uses Elite’s EDGE FREE® technology. The EDGE FREE® design resembles a giant size flat panel TV display.
- The Aeon includes a bezel trim to further enhance the frame appearance and absorb projector overshoot. An optional LED kit is available for backlighting. The material included is our ISF Certified Cine White® UHD-B which produces accurate colors in a light controlled environment as the director intended.
In order for the Cine White® UHD-B to maintain its projection qualities and optimum performance please refer to the list below for proper maintenance and cleaning.
- Use a dry microfiber cloth to remove dust from the screen’s surface.
- When cleaning, use a damp microfiber cloth with warm water to remove any marks.
- Never rub or apply pressure when cleaning the surface.
- Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
- In order to avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other sharp or abrasive objects.
Hardware Parts List
Item
|
Parts List
| 92’’| 100’’| 110’’| 120’’| 125’’| 135’’| 150’’| 180’’|
200’’
---|---|---|---|---|---|---|---|---|---|---
a.| Center Joints- M4 (bottom position)| 2| 2| 2| 2| 2| 2| 2| 2| 2
b.| Center Joints-D5 (top position)| 2| 2| 2| 2| 2| 2| 2| 2| 2
c.| Elbow Joints M4 (bottom position)| 4| 4| 4| 4| 4| 4| 4| 4| 4
d.| Elbow Joints D5 (top position)| 4| 4| 4| 4| 4| 4| 4| 4| 4
e.| Side cover Center Joints- M4| 2| 2| 2| 2| 2| 2| 2| 2| 2
f.| Side cover Elbow Joints M4| 4| 4| 4| 4| 4| 4| 4| 2| 2
g.| M4x7 Screws| 24| 24| 24| 24| 24| 24| 24| 24| 24
h.| Spring| 52| 56| 66| 68| 72| 78| 84| 104| 112
i.| Spring Hook| 2| 2| 2| 2| 2| 2| 2| 2| 2
j.| wall brackets| 4| 4| 4| 4| 4| 4| 4| 6| 6
k.| Φ5×50 Wall Screws| 8| 8| 8| 8| 8| 8| 8| 12| 12
l.| Hollow Wall anchors| 8| 8| 8| 8| 8| 8| 8| 12| 12
m.| M4x4 Screws| 24| 24| 24| 24| 24| 24| 24| 24| 24
n.| Angle cover| 4| 4| 4| 4| 4| 4| 4| 4| 4
o.| Center Support Bar| 1| 1| 1| 1| 1| 1| 1| 2| 2
p.| White gloves| 2| 2| 2| 2| 2| 2| 2| 2| 2
q.| Spring| 4| 4| 4| 4| 4| 4| 4| 4| 4
r.| Φ3 mm Long Iron (sides) rod / Short rod (top/bottom)| 2/4| 2/4| 2/4|
2/4| 2/4| 2/4| 2/4| 2/4| 2/4
Frame Assembly
-
Step 1
Place the included soft padded EPE sponge sheet on a clean area where the screen will be assembled. -
Step 2
Position the pieces of the frame on the EPE sponge in the arrangement shown below
-
Step 3
Insert center joint (a/b) connectors into one-half of the horizontal frame (B/C) and secure with the M4x7 screws (M) as shown in the illustration below.
Tip: The center joint (b) with the larger diameter holes should be on top .
-
Step 4
Connect the elbow joints (c/d) to the top and bottom sections of the vertical frame. Once inserted, connect the vertical sections to the horizontal frame sections. Make sure all holes are in alignment and the frame pieces are flush (no gaps). They should form perfect right angles.
Tip: The elbow joint (d) with the larger diameter holes should be on top.
-
Step 5: Secure the elbow joints by fastening them with M4x7 screws (g), 4 at each corner.
Screen Material -
Step 6
Put on the white gloves (p) and carefully unroll the screen material on a clean surface from the roller to the other side as shown below. The back side of the screen material should be placed upwards.
12222022JA SN 211M +
-
Step 7 Insert the rods (r) through the holes according to their corresponding lengths on each edge of the screen as shown below. The short rods (top/bottom) will overlap to secure a firm grasp in the middle areas.
-
Step 8
Carefully and gently place the assembled frame on top of the screen material in the marked areas as shown below. Make sure to not allow the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.
*Make sure the frame corners are positioned in the marked areas
of the material.
Center Support Bar -
Step 9
Insert the Center Support Bar (o) into the upper top groove on the back of the frame with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove.
Diagonal Sizes of 150” and belowuse 1 x Center Support Bar
Diagonal Models above 150” require 2 x Center Support Bars
-
Step 10
Hook one end of the spring and secure inside the groove of the frame, use the spring hook (h) to attach the spring to the exposed part of the rod (r) in the following order.
Begin by first attaching the center points on both vertical (left/right) sides, steps 1-2. Then the center points on both horizontal (top/bottom) sides, steps 3-4. Once all center points have been secured, make sure the screen material is still within the marked areas before proceeding to attach the next springs. Continue attaching the rest of the springs to the material in the following order in steps 5-12.
To avoid ripples forming in the material it is
imperative that all of the corners are properly wrapped around the edges as
illustrated in the check mark diagrams.
Note (after all springs have been attached)
Correct material installation –Corners of the screen material are properly
wrapped around the corner edges of the frame and material is evenly tensioned
and flat, creating a nicely taut surface.
Incorrect material installation –The corners of the screen material are not
properly wrapped along the edge of the frame leaving the material with
unbalanced tension and an uneven finish. To correct, detach springs from
material at the corner(s) where material does not lie flat along the edge of
the frame, reposition the material so that it lies flat and wraps along the
edge of the frame, and reattach springs to the material.
How to avoid getting ripples on the screen’s material surface
- Solution : Pull and smooth out the material using your hand from the center to the corners, creating a nicely taut surface as shown below.
Edge Trim Installation
ATTENTION : THE TOP EDGE TRIM PIECE WITH THE LOGO SHOULD BE INSTALLED ON
THE TOP.
-
Step 11
Place the edge trim frame pieces over each end of the frame.
Connect edge trim frames (e/f) together using the M4 center joint
(e) and secure with four of the M4x4 screws (m) as show in Step 1. Repeat for
other side.
Once both top and bottom edge trim frames have been connected, attach the vertical (left/right) sides edge trim frames (d) using the elbow joints (f) and secure with four M4x4 screws (m) on all corners, Step 2.
-
Step 12
Install the angle cover (n) on each corner of the frame using the M4x4 screws (m). Note: The angle cover screws holes align with the screw holes on the elbow joint.
Peel off the double-sided tape. -
Step 13
Install the springs (q) in each middle area to further support the bezel trim edge frame.
Wall Installation -
Step 14
Measure the overall length and height of the frame and drill holes for the top brackets. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. If not installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws with a screwdriver. Make sure the brackets are leveled.
Diagonal Sizes of 150” and below use 4 x wall brackets
Model/Size| X = Wall bracket distance| X1 = Bracket hole
distance| Y = Top/Bottom Wall Bracket Height
---|---|---|---
92’’| 1100mm (43.30”)| 30mm (1.18”)| 980mm (38.58”)
100’’| 1200mm (47.24”)| 30mm (1.18”)| 1080mm (42.52”)
110’’| 1300mm (51.18”)| 30mm (1.18”)| 1210mm (47.64”)
120’’| 1400mm (55.12”)| 30mm (1.18”)| 1330mm (52.36”)
125’’| 1400mm (55.12”)| 30mm (1.18”)| 1400mm (55.12”)
135’’| 1500mm (59.06”)| 30mm (1.18”)| 1520mm (59.84”)
150’’| 1600mm (62.99”)| 30mm (1.18”)| 1710mm (67.32”)
Diagonal Models above 150” require 6 x wall brackets
Model/Size| X = Wall bracket distance| X1 = Bracket hole
distance| Y = Top/Bottom Wall Bracket Height
---|---|---|---
180’’| 1000mm (39.37’’)| 30mm (1.18”)| 2080mm (81.88’’)
200’’| 1100mm (43.30’’)| 30mm (1.18”)| 2330mm (91.73’’)
- Step 15
Position the fixed frame screen onto the top wall brackets as shown below and push down at the center of the top of the frame to secure.
For Technical Support or an Elite Screens contact in your area, visit www.elitescreens.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>