Honeywell TR50 Indoor Air Quality Sensor Instruction Manual

Honeywell TR50 Indoor Air Quality Sensor

INDOOR AIR QUALITY SENSOR TR50

Specifications

• Dimensions (H x W x D): 4.45 inches x 3.54 inches x 0.89 inches (113 mm x 90 mm x 23 mm)
• Weight : 0.16 lbs (4 mm)

Product Usage Instructions

Installation

1. Switch OFF the power supply before initiating the TR50 sensor installation.
2. Loosen the bottom screw by turning it anticlockwise with the help of a screwdriver.
3. Separate the front unit and wall plate by pulling out the tape from the bottom to do the wiring.
4. Pull the cables through the junction box and do wiring.
   • Solid Wire (Strongly Recommended)
   • Stranded Wire (Alternative)
5. Fix the wall plate with the help of two screws to the Junction box.
6. Tighten the bottom screw to fix the front unit and wall plate.
7. Attach the front unit to the wall plate, making sure the latches on each side are well matched.
8. Switch ON the power supply to start the TR50 Smart Sensor. Some measured values reach their accuracy only after 2 days.

Frequently Asked Questions (FAQ)

• Q: What are the dimensions of the INDOOR AIR QUALITY SENSOR TR50?
  • The dimensions of the INDOOR AIR QUALITY SENSOR TR50 are 4.45 inches x 3.54 inches x 0.89 inches (113 mm x 90 mm x 23 mm).
• Q: What type of wire is recommended for the wiring?
  • Solid wire is strongly recommended for the wiring, but stranded wire can be used as an alternative.
• Q: How long does it take for the sensor to reach its accuracy?
  • Some measured values of the sensor reach their accuracy only after 2 days.

INDOOR AIR QUALITY

SENSOR TR50

Mounting Instruction

Introduction
The smart sensor device is designed to be mounted on a wall, indoors. Mount in a clean, dry location away from windows, air ducts, and other places where environmental factors may affect readings. If you mount the sensor on the interior of an outside wall, thoroughly insulate it, so outside air behind the sensor does not affect the sensor reading.

Dimension
4.45 inches x 3.54 inches x 0.89 inches (113 mm x 90 mm x 23 mm)

Power Supply
24 VAC/VDC 3.8 VA, 18-30 VDC 1.2 W

Location

All the dimensions shown are in feet’s (meters).

Junction Box

All the dimensions shown are in inches (mm).

Installation Instructions

1. Switch OFF the power supply before initiating the TR50 sensor installation.
2. Loosen the bottom screw by turning it anticlockwise with the help of a screwdriver.
3. Separate the front unit and wall plate by pulling out the tape from the bottom to do the wiring.
4. Pull the cables through the junction box and do wiring.
5. Fix the wall plate with the help of two screws to the Junction box.
6. Attach the front unit to the wall plate, making sure the latches on each side are well matched.
7. Tighten the bottom screw to fix the front unit and wall plate.
8. Switch ON the power supply to start the TR50 Smart Sensor. Some measured values reach their accuracy only after 2 days.

REGULATION (EU) No

According to Article 33 of the Reach Regulation, substances listed below may be contained in these products above the threshold level of 0.1% by weight of listed article.

Honeywell Building Technology 715 Peachtree Street NE Atlanta, GA 30308

• customer.honeywell.com
• buildingcontrols.honeywell.com
• ® U.S. Registered Trademark
• © 2023 Honeywell International Inc.
• 31-00566M-01 | Rev.03-23

References

• Honeywell Building Management Systems (BMS)
• Building Automation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>