BRAYER BR1115 Espresso Machine Instruction Manual

Instruction manual
Espresso machine BR1115

BRAYER is an Austrian consumer electronics brand.
The importer in Russia – “Grantel” LLC.
+7(495) 297-50- 20, info@brayer.su brayer.su

ESPRESSO MACHINE BR1115
The coffee maker is designed for brewing espresso coffee, making cappuccino coffee or latte coffee.

ATTENTION!
For additional protection it is reasonable to install a residual current device (RCD) with nominal operation  current not exceeding 30 mA, to install RCD, contacta specialist.

DESCRIPTION

1. Removable tray
2. Removable tray grid
3. Pullout tray for small cups
4. Filter holder handle
5. Thermometer
6. Cup warming tray
7. «Espresso»-button for making espresso
8. Cappuccino button «Cappuccino»
9. Latte button «Latte»
10. Cappuccinator
11. Power switch «0/I»
12. Water tank lid
13. Removable water tank
14. Cappuccinator pipe angle adjustment bar
15. Cappuccinator pipe
16. Upper lid of the cappuccinator
17. Milk/frothed milk supply control knob
18. Removable milk container
19. Filter retainer
20. Filter holder
21. Small filter
22. Large coffee filter
23. Measuring spoon

SAFETY MEASURES AND COFFEE MAKER OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the coffee maker and keep it for future reference.

• Use the coffee maker for its intended purpose only, as specified in this manual.

• Mishandling the coffee maker can lead to its breakage and cause harm to the user or damage to his/her property and it is not covered by warranty.

• The coffee maker is intended for making espresso and cappuccino coffee and warming up ready drinks. Do not warm any other liquids.

• Make sure that the operating voltage of the coffee maker indicated on the label corresponds to your home mains voltage.

• The power plug is equipped with a grounding contact, plug it into the socket with

• reliable grounding contact. In case of short circuit the grounding reduces the risk of electric shock.

• Contact an electrical technician, if you are not sure that your sockets are installed properly and grounded.

• To prevent fire do not use adapters designed for connecting the power plug to the mains socket without grounding contact.

• In case of sparking in the mains socket and occurrence of smell of burning, unplug the unit and apply to the organization maintaining your home mains.

• If smoke appears from the unit body, unplug the unit and take measures to prevent fire spreading.

• Use and store the coffee maker at the temperature above 0 °C.

• Do not use the coffee maker outdoors.

• It is not recommended to use the unit during lightning storms.

• Protect the unit from impacts, falling, vibrations and other mechanical stress.

• Never leave the plugged-in coffee maker unattended.

• To avoid fire, electric shock or physical injuries, do not immerse the power plug, the power cord or the coffee maker body into water or any other liquids.

• Do not use the coffee maker in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.

• If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water.

• Do not use the coffee maker near heating appliances, heat sources or open flame.

• Do not use the unit in places where aerosols are used or sprayed, and in proximity to inflammable liquids.

• Place the coffee maker on a flat stable surface; do not place it on the edge of a table. Do not let the power cord hang from the edge of the table and make sure it does not touch hot surfaces or sharp edges of furniture.

• Do not place the coffee maker on hot surfaces.

• Do not touch the power cord and the power plug with wet hands.

• Use only the coffee maker parts and accessories supplied with the unit.

• Before switching the coffee maker on, make sure that all removable parts are installed properly.

• Ensure that the water level in the water tank is not below the minimal mark.

• Do not switch the coffee maker on if the water tank is empty.

• To avoid getting burns by hot steam be careful when frothing milk or warming the ready drinks.

• The filter holder surface, the cappuccinator pipe and the cappuccinator tip can get rather hot. Be cautious and careful when in contact with hot surfaces.

• Do not remove the filter holder during coffee maker operation.

• Let the unit cool down completely before cleaning and removing the accessories.

• Unplug the coffee maker before cleaning or when you are not using it. When unplugging the coffee maker hold only the power cord plug and carefully remove it from the mains socket, do not pull the power cord — this can lead to  damage of the power cord or the socket or cause short circuit.

• For children safety reasons do not leave polyethylene bags, used as a packaging, unattended.
  ATTENTION! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

• The coffee maker is not intended for usage by children.

• Do not leave children unattended to prevent using the unit as a toy.

• Do not allow children to touch the unit and the power cord during the coffee maker operation.

• Place the unit out of reach of children during the operation and cooling down.

• This unit is not intended for usage by physically or mentally disabled persons (including children) or

• by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• From time to time check the power cord and the power plug integrity.

• If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.

• Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after it was dropped, unplug the unit and apply to the service center.

• Transport the coffee maker in the original package.

• Keep the unit out of reach of children and disabled persons.

COFFEE MAKER IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE COFFEE MAKER FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE USING THE COFFEE MAKER

After unit transportation or storage at low temperature, it is necessary to keep it for at least three hours at room temperature.

• Unpack the coffee maker and remove all the packaging materials.
• Keep the original package.
• Read the safety measures and operating recommendations.
• Check the delivery set.
• Examine the coffee maker for damages, in case of damage do not plug it into the mains.
• Make sure that the specifications of power supply voltage specified on the lower panel of the unit correspond to the specifications of your mains. When  the unit is used in the mains with 60 Hz frequency, itdoes not need any  additional settings.
• Wipe the surface of the coffee maker body with a clean, slightly damp cloth to remove dust.
• Before using the coffee maker for the first time, wash all removable parts (1, 2, 12, 13, 16, 18, 20, 21, 22, 23) with warm water and neutral detergent and dry them.

BEFORE USING THE UNIT
ATTENTION! If you switch the coffee maker on and don’t perform any actions, the coffee maker will switch off in 15 minutes. To switch the coffee maker on press any button (7, 8, 9).

• Place the coffee maker on a steady flat heat-resistant surface, the distance from the side walls of the coffee maker should be at least 20 cm, and the gap above the coffee maker should be at least 30 cm.

• Do not use the coffee maker under kitchen shelves of cupboards. They can be damaged by the steam releasedduring the coffee maker operation.

• The coffee maker should be placed out of reach of small children.
  Attention! Before making coffee for the first time it is recommended to wash the broiler, the cappuccinator lid (16) and the milk container (18).

• Make sure that the removable tray (1) and the tray grid (2) are installed to their places.

• Remove the lid (12), remove the water tank (13).

• Fill the tank (10) with cold water up to the maximal level mark, install the tank (13) back to its place.
  Note: the tank (13) is intended for water only, do not fill the tank (10) with other liquids, such as milk.

• Take the container (18), pull it towards yourself and remove it, remove the cappuccinator from the container (18) (pic. 1). Fill the container with water up to the maximal level mark.
  Note: the cappuccinator container (18) is intended for milk only, do not fill the container (18) with other liquids, use water only in the cappuccinator lid (16) washing mode.

• Install the cappuccinator lid (16) on the container (18) and install the cappuccinator back to its place until the lock clicking.
  Notes: after installing the container (18) with the lid (16) back to its place always check if the cappuccinator is installed and fixed properly.

• Set the milk supply intensity control knob (17) to the middle position.

• Install one of the coffee filters (21 or 22) into the filter holder (20) matching the ledge on the filter (21 or 22) with the hole on the holder (20) and turn the filter (21 or 22) counter/clockwise. Do not add ground coffee into the filter  (21 or 22) when preparing the coffee maker for work.

• Install the filter holder (20) into the installation place « » and turn the handle (4) to the right as far as it will go « » (pic. 2, 3, 4).

• Place a cup of suitable height and capacity of at least 300 ml on the tray grid (2).

• Direct the cappuccinator pipe (15) into the cup using the cappuccinator pipe angle adjustment bar (14).
  Note: You can change the length of the cappuccinator pipe (15) by turning the pipe (15) counterclockwise, then extend it to the required length, and fix the pipe (15) by turning it clockwise (fig. 9).

• Insert the power plug into the mains socket.

• Switch the coffee maker on by setting the power switch (11) «0/I» to the position «I», the indicator (7, 8, 9) will light up and start flashing.

• When the coffee maker is ready for operation, the indicator (7, 8, 9) will glow constantly.

• To switch the cleaning mode on press the «Cappuccino»-button (8) twice. After cleaning is finished, all the light indicators of the control buttons (7, 8, 9) will light up.

• After you finish cleaning the coffee maker, switch the coffee maker off by setting the switch (11) «0/I» to the position «0».

• Pour the water out of the cup, take the container (18), pull it towards yourself and remove (pic. 1), remove the cappuccinator lid (16) from the container (18), pour the remaining water from the container (18). Slightly lift the front  part of the tray (1) and remove it, pour the water out of it and install the tray (1) back to its place.

• Turn the filter holder handle (4) to the left and remove it (pic. 2, 3, 4). Wait until the filter holder (20) cools down completely and remove the installed filter (21 or 22) turning it counter/clockwise. Wash the filter (21 or 22) and  install it into the filter holder (20).

• If necessary, clean the boiler and the cappuccinator lid (16) several times.

• After cleaning the coffee maker is ready for operation.

CHOOSING THE APPROPRIATE CUP

• Before making coffee, please, select a cup of appropriate capacity according to the table:

Notes: this table has guide values of the amount of the ready drink and is only used to select the volume of the required cup.

RULES OF MAKING ESPRESSO

• Use fresh-ground coffee beans or ground coffee for «espresso» coffee makers.
• Make even and slightly tamp the ground coffee in the filter (21 or 22), you can do it with the back side of the measuring spoon (23) (pic. 5, 6, 7).
• Strength of ready coffee depends on the quality and grinding degree of coffee beans.
• If coffee is pouring out too long, this means the coffee powder is too fine it is tamped too strongly; in this case use coarse-ground coffee and choose the tamping degree experimentally.

THERMOMETER (5)

• The built-in thermometer (5) shows the boiler temperature, if the boiler temperature is over 80°С, you can make coffee.
• When the coffee maker is not used, the thermometer (5) will show the room temperature.

MAKING ESPRESSO
ATTENTION!

• Do not remove the filter holder (20) during making coffee.
  – Do not remove the filter holder (20) right after making coffee, as there is redundant pressure inside, wait a little before removing the filter holder (20).

• Remove the lid (12), remove the water tank (13).

• Fill the tank (13) with cold water, do not exceed the maximal level mark, install the tank (13) back to its place.

• Install one of the coffee filters (21 or 22), depending on the amount of ready coffee, into the filter holder (20) matching the ledge on the filter (21 or 22) with the hole on the holder (20) and turn the filter (21 or 22) counter/ clockwise.

• Add the required amount of ground coffee into the filter (21 or 22) with a measuring spoon (23) and slightly tamp the coffee in the filter (21 or 22) with the back side of the measuring spoon (23) (pic. 5, 6, 7).

• Install the filter holder (20) into the installation place «» and turn the handle (4) to the right as far as it will go «» (pic. 2, 3, 4).

• Place a cup of suitable height and capacity (see the table CHOOSING THE APPROPRIATE CUP) on the grid (2); if you use small cups, take the pullout tray (3) by the lower part and pull it towards yourself, place the cups on it.

• Insert the power plug into the mains socket (pic. 8).

• Note: – During preliminary heating, you can warm up the cups that will be used for making coffee by placing them on the tray (6).

• Switch the coffee maker on by setting the power switch (11) «0/I» to the position «I», the indicator (7, 8, 9) will light up and start flashing.

• When the coffee maker is ready for operation, the light indicator (7, 8, 9) will glow constantly.

• To make one cup of espresso, use the small filter (21) and press the «Espresso»-button (7) once; the light indicator « » will light up.

• To make two cups of espresso, use the larger filter (22) and press the «Espresso»-button (7) twice; the light indicator « » will light up. In this case set one big or two small cups on the grid (2 or 3).

Notes:

• if you need to switch the coffee maker off during the espresso making, press the «Espresso»-button (7) again;
• successive making of coffee should be performed with intervals 2-3 min.
  • Remove the cup with ready drink from the grid (2 or 3).
  • After you finish using the coffee maker, switch the coffee maker off by setting the switch (11) «0/I» to the position «0».
  • Wait until the coffee maker cools down, remove the filter holder (20) and wash the installed filter (21 or 22).

MAKING CAPPUCCINO

ATTENTION! When making cappuccino be careful to avoid burns by outgoing hot steam.

• Make sure that the removable tray (1) and the tray grid (2) are installed to their places.
• Fill the tank (13) with cold water, do not exceed the maximal level mark, install the tank (13) back to its place.
• Take the container (18), pull it towards yourself and remove it (pic. 1), remove the cappuccinator lid (16) from the container (18).
• Fill the container (18) with milk, do not exceed the maximal level mark.
• Install the cappuccinator lid (16) on the container (18) and install the cappuccinator back to the installation place until the lock clicking.
• Install one of the coffee filters (21 or 22) into the filter holder (20) matching the ledge on the filter (19 or 20) with the hole on the holder (20) and turn the filter (21 or 22) counter/clockwise.
• Add the required amount of ground coffee into the filter (21 or 22) with a measuring spoon (23) and slightly tamp the coffee in the filter (21 or 22) with the back side of the measuring spoon (23) (pic. 5, 6, 7).
• Install the filter holder (20) into the installation place « » and turn the handle (4) to the right as far as it will go « » (pic. 2, 3, 4).
• Place a cup of suitable height and capacity on the grid (2) (see the table «CHOOSING THE APPROPRIATE CUP»).

Note: During preliminary heating, you can warm up the cups that will be used for making coffee by placing them on the tray (6).

• Direct the cappuccinator pipe (15) into the cup using the cappuccinator pipe angle adjustment bar (14), if necessary, change the length of the cappuccinator pipe (15) (fig. 9).

• Turn the frothed milk supply (intensity) control knob (17) to the right (in this position it produces more frothed milk). Turn the frothed milk supply (intensity) control knob (17) to the left (in this position it produces less frothed milk) (pic. 10, 11).
  Notes: you can adjust the milk foam supply intensity when making cappuccino.

• Insert the power plug into the mains socket.

• Switch the coffee maker on by setting the power switch (11) «0/I» to the position «I», the indicator (7, 8, 9) will light up and start flashing.

• When the coffee maker is ready for operation, the light indicator (7, 8, 9) will glow constantly.

• To make one cup of cappuccino use a small filter (21) and press the «Cappuccino»-button (8) once; the light indicator « » will light up.

• To make two cups of cappuccino use a big filter (20) and press the «Cappuccino»-button (8) twice; the light indicator « » will light up.

Note: if you need to switch the coffee maker off during the cappuccino making, press the button (6) «Cappuccino» again.

• Remove the cup with the ready drink from the grid (2).
• After you finish using the coffee maker, switch the coffee maker off by setting the switch (11) «0/I» to the position «0».
• Wait until the coffee maker cools down, remove the filter holder (20) and wash the filter (21 or 22).
• If there is some milk left in the cappuccinator, remove the cappuccinator and put it in the fridge (pic. 12). If you used all the milk during the coffee making, it is recommended to remove and wash the cappuccinator (see the chapter  «CAPPUCCINATOR CLEANING»).

MAKING LATTE

ATTENTION! When making latte be careful to avoid burns by outgoing hot steam.

• Make sure that the removable tray (1) and the tray grid (2) are installed to their places.
• Fill the tank (13) with cold water, do not exceed the maximal level mark, install the tank (13) back to its place.
• Take the container (18), pull it towards yourself and remove it (pic. 1), remove the cappuccinator lid (16) from the container (18).
• Fill the container (18) with milk, do not exceed the maximal level mark.
• Install the cappuccinator lid (16) on the container (18) and install the cappuccinator back to its place until the lock clicking.
• Install one of the coffee filters (21 or 22) into the filter holder (20) matching the ledge on the filter (21 or 22) with the hole on the holder (20) and turn the filter (21 or 22) counter/clockwise.
• Add the required amount of ground coffee into the filter (21 or 22) with a measuring spoon (22) and slightly tamp  the coffee in the filter (21 or 22) with the back side of themeasuring spoon (23) (pic. 5, 6, 7).
• Install the filter holder (20) into the installation place « » and turn the handle (4) to the right as far as it will go « » (pic. 2, 3, 4).
• Place a cup of suitable height and capacity on the grid (2) (see the table «CHOOSING THE APPROPRIATE CUP»).
• Note: – During preliminary heating, you can warm up the cups that will be used for making coffee by placing them on the tray (6).
• Direct the cappuccinator pipe (15) into the cup using the cappuccinator pipe angle adjustment bar (14), if necessary, change the length of the cappuccinator pipe (15) (fig. 9).
• Turn the frothed milk supply (intensity) control knob (17) to the right (in this position it produces more frothed milk). Turn the frothed milk supply (intensity) control knob (17) to the left (in this position it produces less frothed  milk) (pic. 10, 11).

Notes: you can adjust the milk foam supply intensity when making latte.

• Insert the power plug into the mains socket.

• Switch the coffee maker on by setting the power switch (11) «0/I» to the position «I», the indicator (7, 8, 9) will light up and start flashing.

• When the coffee maker is ready for operation, the light indicator (7, 8, 9) will glow constantly.

• To make one cup of latte use a small filter (21) and press the «Latte»-button (9) once; the light indicator « » will light up.

• To make two cups of latte use a big filter (20) and press the «Latte»-button (9) twice; the light indicator « » will light up.
  Note: if you need to switch the coffee maker off during the latte making, press the «Latte»-button (9) again.

• Remove the cup with the ready drink from the grid (2).

• After you finish using the coffee maker, switch the coffee maker off by setting the switch (11) «0/I» to the position «0».

• Wait until the coffee maker cools down, remove the filter holder (20) and wash the filter (21 or 22).

• If there is some milk left in the cappuccinator, remove it and put the cappuccinator into the fridge (pic. 12), if you used all milk during making coffee, it is recommended to remove the cappuccinator and clean it (see the chapter  «CAPPUCCINATOR CLEANING»).

MAKING FROTHED MILK

• You can make necessary amount of frothed milk anytime.

• You can use the frothed milk for making hot chocolate, macchiato, masala tea etc.

• It is important that milk for making frothed milk is fresh and cold and without additives.

• Take usual whole milk with fat status from 4% to 6%, cream fat status is not less than 10%.

• Prepare the coffee maker as described in the chapters above, but do not add ground coffee into the filters (21 or 22).

• Place a cup of suitable height and capacity on the grid (2).

• Direct the cappuccinator pipe (15) into the cup using the cappuccinator pipe angle adjustment bar (14), if necessary, change the length of the cappuccinator pipe (15) (fig. 9).

• Turn the frothed milk supply (intensity) control knob (17) to the right (in this position it produces more frothed milk) (pic. 11).
  Notes: you can adjust the milk foam supply intensity when making.

• Switch the coffee maker on by setting the power switch (11) «0/I» to the position «I», the indicator (7, 8, 9) will light up and start flashing.

• When the coffee maker is ready for operation, the light indicator (7, 8, 9) will glow constantly.

• Press and hold the «Cappuccino»-button (8) for 3 seconds, the indicators « » and « » will light up.

• After making the necessary amount of frothed milk stop the process by pressing the «Cappuccino»-button (8) again.

• Remove the cup with frothed milk and use the frothed milk for the intended purpose.

• After you finish using the coffee maker, switch the coffee maker off by setting the switch (11) «0/I» to the position «0».

• If there is some milk left in the cappuccinator, remove it and put the cappuccinator into the fridge (pic. 12), if you used all milk during making coffee, it is recommended to remove the cappuccinator and clean it (see the chapter  «CAPPUCCINATOR CLEANING»).

CAPPUCCINATOR CLEANING

• We recommend cleaning the cappuccinator after the milk container (18) is empty.
• Take the container (18) and remove it (pic. 1), remove the cappuccinator lid (16) from the container (18).
• Wash the container (18) with a neutral detergent, remove the milk intake pipe from the cappuccinator lid (16) and wash it, rinse all the parts, dry them and install the milk intake pipe back to its place.
• Turn the steam nozzle counterclockwise and remove it from the cappuccinator (16) body (pic. 11), wash the nozzle.
• Remove the cappuccinator pipe (15) by turning the pipe (15) counterclockwise, rinse the pipe (15), install it  back to its place, fix the pipe (15) by turning it clockwise(fig. 9).
• Grasp the left side and raise the silicone plug (pic. 14), rinse the cappuccinator lid (16) under a warm water jet, close the silicone plug.
• Install the steam nozzle back to its place and turn it clockwise (pic. 15).
• Prepare the coffee maker as described in the chapters above, but do not add ground coffee into the filter (21 or 22).
• Place a cup of suitable height and capacity on the grid (2).
• Fill the container (18) with water, do not exceed the maximal level mark.
• Install the cappuccinator lid (16) on the container (18) and install the cappuccinator back to its place until the lock clicking.
• Direct the cappuccinator pipe (15) into the cup using the cappuccinator pipe angle adjustment bar (14), if necessary, change the length of the cappuccinator pipe (15) (fig. 9).
• Turn the frothed milk supply (intensity) control knob (175) to the right to the position « ».
• Switch the coffee maker on by setting the power switch (11) «0/I» to the position «I», the indicator (7, 8, 9) will light up and start flashing.
• When the coffee maker is ready for operation, the light indicator (7, 8, 9) will glow constantly.
• Press and hold the «Latte»-button (9) for 3 seconds, the indicators « » and « » will light up.
• After you finish using the coffee maker, switch the coffee maker off by setting the switch (11) «0/I» to the position «0».
• Wait until the coffee maker cools down, take the container (18), pull it towards yourself and remove it (pic. 1), remove the cappuccinator lid (14) from the container (18).
• Pour the remaining water out of the container (18), wipe the container with a dry cloth and dry the cappuccinator lid (16).
• Before assembling make sure that the cappuccinator lid and the container are dry. Install the cappuccinator lid (16) on the container (18) and install the cappuccinator on the coffee maker.

DESCALING

• Scale inside the boiler affects the taste of ready coffee, slows down the coffee making and reduces the service life of the coffee maker.
• Note that the thicker the scale, the more difficult it is to remove, that’s why we recommen regularly removing scale for effective operation of the coffee maker (see the table).
• The buttons (7, 6, 9) light indicators flashing by rotation will remind you about descaling.
• You can use special descaling agents for espresso coffee makers or coffee machines to remove scale. You can also use table vinegar or citric acid solution (2 teaspoons of citric acid per 1 liter of water).
• Follow the instructions on the usage of the descaling agent, pour it into the water tank (13).
• Install one of the coffee filters (21 or 22) into the filter holder (20) matching the ledge on the filter (21 or 22) with the hole on the holder (20) and turn the filter (21 or 22) counter/clockwise.
• Place a cup of suitable height and capacity on the grid (2).
• Direct the cappuccinator pipe (15) into the cup using the cappuccinator pipe angle adjustment bar (14), if necessary, change the length of the cappuccinator pipe (15) (fig. 9).
• Insert the power plug into the mains socket.
• Switch the coffee maker on by setting the «0/I» power switch (11) to the «I» position.
• To switch the cleaning mode on, press simultaneously the button (9) «Latte» and the button (7) «Espresso».
• In the descaling mode the light indicators slowly flash by rotation, after 30 minutes the light indicators will start flashing faster. Remove the container (13), drain the remaining descaling solution and fill the container (13) with clean water. Install the container (13) back to its place.
• Pour the descaling solution out from the cup, place the cup on the grid (2).
• Simultaneously the button (9) «Latte» and the button (7) «Espresso» to continue cleaning the coffee maker.
  In approximately 30 minutes the coffee maker cleaning will be finished, and the coffee maker will switch to the standby mode, all buttons (7, 8, 9) light indicators will glow constantly.

Notes:

• You can temporarily switch the descaling notification off by pressing any of the buttons (7, 8, 9) and make coffee. After the coffee making the coffee maker will remind you about descaling again with flashing light indicators.
• Do not delay descaling of the coffee maker for a long time and perform cleaning as soon as possible.
• Wash the water tank (13) and the milk container (18) with warm water and soft detergent, then dry them.
• If there is mineral scale in the water tank (13), pour some citric acid solution or table vinegar in the water tank (13). After mineral scale dissolves, wash the water tank (13).
• Slightly lift the front part of the tray (1) and remove it, pour the water out of it, remove the grid (2) from the tray (1), wash the tray (1) and the grid (2) with water and neutral detergent, dry them and install back to their places.

STORAGE

• Before taking the coffee maker away for long storage, unplug it and let the unit cool down.
• Clean the coffee maker.
• Pack the coffee maker in the original package.
• Use and store the coffee maker at the temperature above 0 °C.
• Keep the coffee maker in a dry cool place out of reach of children and disabled persons.

TROUBLES AND TROUBLESHOOTING

The coffee
maker can’t be switched on| No voltage in the mains socket.
The power plug is not completely inserted into the socket| Make sure that the mains socket is operating by connecting a known good electric appliance to it.
Disconnect the power plug and connect it into the socket
Water leaks from the lower part of the unit| The water tray is full| Pour out water from the tray
Coffee leakage from the filter holder| Loose connection of the filter and boiler gasket, ground coffee got on the edges of the filter| Clean the edges of the filter
Coffee has a
foreign smell| Wrong process of scale removal in the boiler
Improper storage of coffee.| See the chapters «Before using the unit», «Descaling» and perform them several times
Use fresh ground coffee.
Keep coffee in a dry cool place.
Steam doesn’t froth milk| You used skimmed milk
Milk is not cold enough
The cappuccinator pipe is blocked| Use only whole milk with fat content 4-6%
Use cold milk
Clean the cappuccinator pipe and the cappuccinator lid (see the chapter «CLEANING THE CAPPUCCINATOR»)

DELIVERY SET

1. Coffee maker – 1pc.
2. Coffee filter – 2 pcs.
3. Measuring spoon – 1 pc.
4. Instruction manual – 1 pc.

TECHNICAL SPECIFICATIONS

• Power supply 220-240 V, ~ 50-60 Hz
• Rated input power: 1300 W
• Water tank capacity: 1,5 l
• Milk tank capacity: 0,5 l

RECYCLING
To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.
The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.
The manufacturer reserves the right to change the design, structure and specifications not affecting general operation principles of the unit, without prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>