PROGRESS LIGHTING P400382 McColl 6-Light Matte Black Transitional LED Chandelier Installation Guide
- June 14, 2024
- PROGRESS LIGHTING
Table of Contents
P400382
6-LT LINEAR CHANDELIER
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Chain Loop | 2 |
| C | Canopy | 3 |
HARDWARE CONTENTS (not actual size)
| | | | | | | |
---|---|---|---|---|---|---|---|---
Hex Nut
Qty:2| Wire Nut
Qty:3| 1/81P Mounting Strap
Qty:1| Finial (1/8IP)
Qty:1| Nipple
Qty:1| Chain
Qty:2| Quick link
Qty:4| Screw (#8)
Qty:1| Flat washer
Qty:1
THANK YOU for selecting Progress Lighting
We can assist you with questions regarding product information, assembly or
missing Parts.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble,operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor
WARNING: If any Special Control Devices are used with this Fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor
CAUTION: All glass is fragile, use care when handling glass shades and
bulbs.
PREPARATION
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damage, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder, drill.
CARE AND MAINTENANCE
Shut off main power supply before cleaning product or changing light bulbs. To
clean, wipe with damp cloth.
Do not use abrasive cleaners or cleaners that contain alcohol.
ASSEMBLY INSTRUCTIONS
-
Loosely thread the hex nut (AA) onto the nipple (EE) and then install this assembly onto the mounting strap (CC). Next, install this assembly to the outlet box using the mounting screws supplied with the outlet box (not included).
-
In this step, you will adjust the depth of the nipple in relation to the canopy depth.
Take the canopy (C) and slip it over the nipple (EE). You will need to adjust the nipple so at least 1/4″ of the threaded portion is exposed through the canopy hole. This is done by adjusting the depth of the nipple (EE) on the mounting strap (CC). When the nipple depth is correctly adjusted, remove the canopy (C) and tighten the top hex nut (AA) against the mounting strap (CC).
-
Equally adjust the arms by carefully turning them out from the center.
-
Pass the wire through the chain loop (B). Attach both chain loops (B) to fixture (A) and secure tightly.
During this step, determine the hanging length of your fixture by removing chain links (FF) and optionally cutting the electrical and ground wire to length.
Do NOT cut electrical or ground wires until this overall length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the chain holder (EE) to allow for easy connections in step 7. -
Once hanging length is determined, open two quick links (GG). Hook the quick link (GG) onto one end of the chain (FF) and to the chain loop (B). Close the quick links (GG) and secure it tightly. Open the other two quick links (GG). Hook the quick links (GG) onto the other end of the chain (FF) and to the canopy loop (C). Close the quick link (GG) and secure it tightly.
With the chain links (FF) closed and all the loops fastened securely, have someone help you hold up the fixture by the canopy (HH) and visually inspect the chain lengths, making sure fixture hangs evenly.
-
You now need to attach the fixture support cable.
This cable will aid you in suppurting the fixture during the wiring‘ connection in step 7. You will need a helper to help hold up the fixture during this step.
Make sure the supply wire is out of the way from the drill for this step.
Use a #29 drill (ø.136) or (3.5mm) bit to create a mounting hole in the side of the junction box.
Next, using the self threaded screw (HH) and flat washer (JJ) provided, secure the support cable into the hole you just drilled in the junction box. Tighten securely.
-
Strip 3/8” of insulation from the electrical wire ends. Using the wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the junction box; connect the SMOOTH fixture wire to the BLACK supply wire from the junction box.
Connect the fixture ground wire and supply ground wire together using a wire nut, or fasten both to the ground screw on the mounting strap. Push all the wire connections carefully into the outlet box. -
Position and attach the canopy (C) onto the nipple (EE) and use the finial (DD) to secure the canopy (HH) tightly to the celiling .
-
Thread the lamps (not included) into the fixture sockets.
Use 60-watt MAX incandescent candelabra base, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed
and under normal conditions of use, are warranted to our customers only to be
free from defects in material and workmanship at time of shipment. All
warranty claims must be asserted within one year from date of purchase of the
subject items; thereafter, warranty claims wil not be honored. Customers’ sole
remedy for a warranty claim or otherwise shall be limited to repair or
replacement of the subject product if it is shown to have been defective in
material or workmanship at time of shipment. Progress’s sole and maximun
liability for a defective product shall never exceed the cost of the subject
product.
EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS
WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR
IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO
CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR
ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE
CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE
SUBJECT PRODUCT OR PRODUCTS.
Therefore, the customer’s sole and exclusive remedy against us for breach of
the warranty, breach of contract or negligence or strict liability or
otherwise shall be limited to repair or replacement of the subject product at
our option (excluding installation and removal charges which shall not be our
liability) or, if we choose, refund of the purchase price. In no case does our
warranty and exclusive remedy extend to anybody other than our customers. Our
customers are not authorized to extend warranties or remedies on our behalf to
anyone. Such unauthorized extensions of warranties or remedies by the customer
shall remain customer’s responsibility. Customer is responsible for
determining the suitability of our products for customer’s use or resale, or
for incorporating them into objects or for applications which customer
designs, assembles, constructs or manufactures.
800-447-0573
8am-8pm (Eastern), Monday-Friday
customerservice@progresslighting.com
93165893
Documents / Resources
|
PROGRESS LIGHTING P400382 McColl 6-Light Matte Black Transitional LED
Chandelier
[pdf] Installation Guide
P400382, 785247255870, 93165893_A Model 1, P400382 McColl 6-Light Matte Black
Transitional LED Chandelier, McColl 6-Light Matte Black Transitional LED
Chandelier, 6-Light Matte Black Transitional LED Chandelier, Matte Black
Transitional LED Chandelier, Transitional LED Chandelier, LED Chandelier,
Chandelier
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>