MuxLab 500412-V2 HDMI 4X4 Inch Matrix Switch Kit User Manual

MuxLab 500412-V2 HDMI 4X4 Inch Matrix Switch Kit

Safety Precautions

To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for future reference.

• Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
• Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near water. Keep the product away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• Install the device in a place with adequate ventilation to avoid damage caused by overheat.
• Unplug the power when left unused for a long period of time.
• Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.

Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or translated without the express permission of MuxLab Inc. Product specifications and information in this document are for reference only, and the content may be updated from time to time without prior notice.

Introduction

The HDMI 4X4 Matrix Switch Kit, HDBT, PoC, 4K/60 (4:4:4) (model: 50041-V2) allows up to four (4) different HDMI sources to be connected and/or distributed to up to four (4) HDMI displays. The unit supports four (4) HDBT outputs for long distance connectivity and four (4) HDMI outputs for local connectivity. The Kit includes four (4) HDBT PoC Receivers which are powered by the Matrix Switch, and support distances up to 150m at 1080p and 120m at 4K via Cat5e/6/7 cable. The unit may be managed via front panel pushbuttons, IR, RS232 and webserver interface.

Features

• HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
• Video resolution up to 4K/60Hz (YUV 4:4:4) on all HDMI & HDBaseT ports
• 4 HDMI inputs, 4 HDMI & HDBaseT mirrored outputs
• HDMI ports transmit 18Gbps lossless uncompressed video bandwidth
• Supports 18Gbps lossless compressed HDBaseT signal transmission
• Supports 4K to 1080P Down Scaler for each output port
• Supports HDR, HDR10, HDR10+, Dolby Vision and HLG
• HDBaseT output can extend video transmission distance up to 492ft / 150m for 1080P or 394ft / 120m for 4K via a single Cat 5e/6/7 cable
• HDMI audio pass-through up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD Master Audio)
• Supports IR matrix
• Supports audio de-embedded via analog and coax ports
• Supports advanced EDID management and CEC control
• 24V POC on all HDBaseT ports
• 1U rack mounted design with front panel display
• Control via front panel buttons, IR remote, RS-232, LAN and Web GUI

Package Contents

• One (1) HDMI 4X4 Matrix Switch Kit, HDBT, PoC, 4K/60 Four (4) HDBaseT Receiver
• One (1) Remote Control
• One (1) 100~240V AC 50/60Hz Power cable
• One (1) RS-232 serial cable (1.5 meters, male to female) Four (4) 3-pin Phoenix Connector
• Four (4) 5-pin Phoenix Connector
• Five (5) IR Blaster cable (1.5 meters)
• Five (5) IR Receiver cable (1.5 meters)
• Ten (10) Mounting Ear (Matrix and Receiver)
• One (1) User manual (available via download)

Specifications

HDBaseT receiver

| Inputs:         1 x HDBT IN [RJ45, 8-pin female] Outputs:  1 x HDMI Type A [19-pin female]

1 x AUDIO OUT [3.5mm Stereo Mini-jack] Controls: 1 x IR IN [3.5mm Stereo Mini- jack]

1 x IR OUT [3.5mm Stereo Mini-jack] 1 x RS-232 [3-pin Phoenix connector]

1 x SERVICE [Mini-USB, Update port]

---|---
Mechanical|
Housing| Metal Enclosure
Color| Black
Dimensions (WxDxH)| Matrix: 440mm x 200mm x 44.5mm Receiver: 140mm x 65mm x 18mm
Weight| Matrix: 3.1Kg       Receiver: 155g
Power Supply| AC 100 – 240V 50/60Hz
Power Consumption| 60W (Max)
Operating Temperature| 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature| -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity| 20~90% RH (non-condensing)
Generic Specification|
Compliance| Regulatory: FCC, CE, RoHS
Warranty| 2 years
Order Information| 500412-V2 HDMI 4X4 Matrix Switch Kit HDBT, PoC, 4K/60 (UPC:627699034125)

Operation Controls and Functions

Matrix Panel

rate, IP Address.
2| Power LED| The LED will illuminate in green when the product is working normally, and red

when the product is on standby.

3| Output/Input buttons| You need to press an output button (1~4) firstly and then press an input button (1~4) to select the corresponding input source for the output port.
4| Menu/Enter/Up/Down| ① EDID Setting: On the initial display screen, press “MENU” button to enter “Select EDID” interface, press “UP/DOWN” button to select the required EDID and press the “ENTER” button to enter “Copy to Input:” interface. Then press “UP/DOWN” button to select the input port you need to set, and press “ENTER” button again to confirm.

② Baud Rate Setting: On the initial display screen, press “MENU” button twice

to enter “SELECT BAUD” interface and press “UP/DOWN” button to select the required Baud rate, finally press the “ENTER” button to confirm the setting.

③ IP Address Check: On the initial display screen, press “MENU” button three times to enter the IP interface and check the current IP address, then press “UP/DOWN” button to switch DHCP ON/OFF, finally press the “ENTER” button to confirm the setting. Pressing the “MENU” button again will return to the initial display status.

5| Power Button| Press and hold the POWER button for 3 seconds to enter the standby mode,

then press the button again to wake up the device.

6| IR Window| IR receiver window, it only receives the IR remote signal from this product.
7| Lock Button| Press the LOCK button to lock front panel buttons (Except the power button);

Press the button again to unlock.

signal will emit to the “IR OUT” port of the HDBaseT Receiver.
2| IR Out (1/2/3/4/ALL) ports| Connect to IR blaster cable, the IR emit signal is from the “IR IN” port of the

HDBaseT Receiver.

3| Audio Out (1-4) ports| 4 groups of coaxial and balanced analog audio mirrored output ports. AUDIO OUT (1-4) follows the video output of OUTPUT (1-4) ports.
4| GND| Connect the housing to the ground.
5| Power Input| Power port: Connect to 100~240V AC 50/60Hz power cable.

Power switch: Press the switch to turn on/off the power.

6

| ****

Output (1-4) ports

| HDMI output ports, connect to HDMI display device such as TV or monitor with an HDMI cable.

HDBT mirrored outputports, connectto HDBaseT Receiver via CAT cable.

7| Input (1-4) ports| HDMI input ports, connect to HDMI source device such as DVD or PS4 with an HDMI cable.

8

| ****

Control Ports

| TCP/IP: The link port for TCP/IP control. Connect to an active Ethernet port with an RJ45 cable.

RS-232: Command control port. Connect to a PC or control system with a D- Sub 9-pin cable to control the Matrix.

HDBaseT Receiver Panel

IR Remote

1. Power on or Standby: Power on the Matrix or set it to standby mode
2. Output 1: Press 1121314 button to select input sourceto HDMI OUTPUT 1.
3. Output 2: Press 1121314 button to select input sourceto HDMI OUTPUT 2.
4. Output 3: Press 1121314 button to select input source to HDMI OUTPUT 3. Output 4: Press 1121314 button to select input source to HDMI OUTPUT 4.

Select the last or next input source button.

IR Control System

The product is not only a matrix switch but also an extender. It supports bi- directional IR control. When Matrix is connected to HDBaseT Receiver through Cat 5e/6/7 cable, you can control remote display device (HDBaseT) or input source device (Matrix) through IR signal transmission. But you must note that the IR signal transmission method is different from the method from Matrix (local) to HDBaseT Receiver (remote) and from HDBaseT Receiver (remote) to Matrix (local).

At the Matrix end (Local end): the IR signal is one-to-one transmission. For example, the IR IN 1 port signal of the Matrix will emit to IR OUT port of the HDBaseTReceiver 1, and the
IR IN 3 port signal of the Matrix will emit to IR OUT port of the HDBaseTReceiver 3. It doesn’t follow the video switch to change.IR IN ALL port signal of the Matrix will emit to all IR OUT ports of HDBaseT receivers simultaneously. Please see the following connection diagram.

At HDBaseT receiver (Remote end): IR signal follows video switch to change. For example, the HDMI output signal on the HDBaseT Receiver 1 is from the HDMI INPUT 2 port, so IR input signal of the HDBaseT Receiver 1 will emit to IR OUT 2 port of the Matrix. The HDMI output signal on the HDBaseT Receiver 3 is from the HDMI INPUT 4 port. Then, IR input signal of the HDBaseT Receiver 3 will emit to IR OUT 4 port of the Matrix etc. Any of HDBaseT Receiver’s IR IN signal can output from IR OUT ALL port of the Matrix and the IR OUT ALL signal of the Matrix depends on your IR remote of source device. Please see the following connection diagram.

IR Cable Pin Assignment

EDID Management
This Matrix has 21 factory defined EDID settings, 2 user-defined EDID modes and 8 copy EDID modes. You can select defined EDID mode or copy EDID mode to input port through on-panel button, RS-232 control or Web GUI.
On-panel button operation: On the initial display screen, press “MENU” button to enter the EDID setting interface, press “UP/DOWN” button to select the required EDID, and press the “ENTER” button to enter “Copy to Input:” interface. Then press “UP/DOWN” button to select the input port you need to set, and press “ENTER” button again to confirm this operation.

RS-232 control operation: Connect the Matrix to PC with a serial cable, then open a Serial Command tool on PC to send ASCII command “s edid in x from z!” to set EDID. For details, please refer to “EDID Setting” in the ASCII command list of “12. RS-232 Control Command”.
Web GUI Operation: Please check the EDID management in the “Input page” of “11. Web GUI User Guide”.

The defined EDID setting list of the product is shown as below:

Web GUI User Guide
The Matrix can be controlled by Web GUI. The operation method is shown as below:
Step 1: Get the current IP Address.
The default IP address is 192.168.1.100. You can get the current Matrix IP address in two ways: The first way: You can get the IP address via panel buttons. On the initial display, press “MENU” button three times to enter the IP interface and check the current IP address.

The second way: You can get the IP address via RS-232control. Send the ASCII command “r ipconfig!” through a Serial Command tool, then you’ll get the feedback information as shown below:

IP:192.168.168.162 in the above figure is the current Matrix IP address (this IP address is variable, depending on what the specific machine returns).
For the details of RS-232 control, please refer to “12. RS-232 Control Command”.
Step 2: Connect the TCP/IP port of the Matrix to a PC with an UTP cable (as shown in the following figure), and set the IP address of the PC to be in the same network segment with the Matrix.

Step 3: Enter the current IP address of the Matrix in your browser on the PC to enter the Web GUI page.

• After entering the Web GUI page, there will be a login page.
• Select the Username from the list and enter the password. The default passwords are:
  Username    User    Admin
  Password      user    admin

After entering the password, click the “LOGIN” button and the following Status page willappear.

Status Page
The Status page provides basic information about the product model, installed firmwareversion and the network settings of the device.

Video Page
You can do the following operations on the Video page:

1. Output : The current device’s OUTPUT port. You can select signal source for it.
2. Input : You can click the drop-down menu to select signal source for the corresponding OUTPUT port .
3. Presets Name : You can name the current scene with maximum length of 12 characters.
4. Presets Set : You can restore the settings of the last saved audio-video matrix switching relationship.
5. Presets Save : You can save audio-video matrix switching relationship.
6. Presets Clear : You can clear the saved audio-video matrix switching relationship.

Input Page
You can do the following operations on the Input page:

1. Inputs : Input channel of the device.
2. Active : It indicates whether the channel is connected to a signal source.
3. Name : The input channel’s name. You can modify it by entering the corresponding name (max length: 12 characters).
4. EDID : You can set the current channel’s EDID. The specific operation is as follows:

Set EDID for the User
Click the “Browse” button, then select the bin file. If you select the wrong EDID file, there willbe a prompt, as shown in the following figure:

Make sure to select the correct file, then you can check the name of the selected file. Select“User 1” or “User 2”, then click “Upload”. After successful setting, it will prompt as follows:

Download the EDID File for the Corresponding Input Channel
Click the drop-down box of “Select EDID File” to select the corresponding input channel. Thenclick “Download” to download the corresponding EDID file.

Output Page
You can do the following operations on the Output page:

1. Outputs : Output channel of the device.
2. Name : The current output channel’s name. You can modify it by entering the corresponding name (max length: 12 characters) in the input box.
3. Type : The current output channel’s type (HDMI or HDBT).
4. Cable : It indicates the connection status of output ports. When the output port is connected to the display, it shows green, otherwise, it shows gray.
5. Scaler Mode : Set the current output resolution mode.
6. Stream : Turn on/off the output stream.

CEC Page
You can perform CEC management on this page:

1. Input Control : You can control the operation of each input source by pressing the icons on the page. (You can control multiple inputs simultaneously).
2. Output Control : You can control the operation of each display, such as power on/off, volume +/-, active source switching. (You can control multiple outputs simultaneously.)

Network Page

Set the Default Network
Click “Set Network Defaults” button, there will be a prompt, as shown in the following figure:

Modify User Password
Click the “User” button, enter the correct Old Password, New Password, and Confirm Password,then click “Save”. After successful modification, there will be a prompt,

Note : Input rules for changing passwords:
(1) The password can’t be empty.
(2) New Password can’t be the same as Old Password.
(3) New Password and Confirm Password must be the same.

Modify Network Setting
Modify the Mode/IP Address/Gateway/Subnet Mask/Telnet Port as required, click “Save” to save the settings, then it will come into effect.
After modification, if the Mode is “Static”, it will switch to the corresponding IP Address;
if the Mode is “DHCP”, it will automatically search and switch to the IP Address assigned by the router.

System Page

1. Panel Lock : Click to lock/unlock panel buttons. “On” indicates that panel buttons are unavailable; “Off” indicates panel buttons are available.
2. Beep : Click to turn on/off the beep.
3. LCD : You can turn on/off the LCD, and set the turn-on time (15s/30s/60s).
4. Serial Baud Rate : Click the value to set the Serial Baud Rate.
5. Firmware Update : Click “Browse” to select the update file, then click “Update” to complete firmware update.
6. Factory Reset : You can reset the machine to factory defaults by clicking “Reset”.
7. Reboot : You can reboot the machine by clicking “Reboot”.

Note : After reset/reboot, it will switch to the login page.

RS-232 Control Command
The product also supports RS-232 control. You need a serial cable with RS-232 male head andDB9 transfer USB male head. The RS-232 head of the serial cable is connected to the RS-232control port with DB 9 at the rear of the Matrix, and the USB head of the serial cable is connected to a PC. The connection method is as follows:

Then, open a Serial Command tool on PC to send ASCII command to control the Matrix. TheASCII command list about the product is shown below.

Application Diagram

2321 Cohen | St-Laurent , H4R 2N7 | Québec, Canada Tel: 514-905-0588 |
Fax:514-905-0589 | Toll free: 1-877-689-5228
info@muxlab.com |salesteam@muxlab.com | www.muxlab.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>