MuxLab 500222 Passive Ceiling Speaker User Manual
- June 14, 2024
- MuxLab
Table of Contents
Passive Ceiling Speaker 8 Ohms/70V/100V, 40W
User Manual
500222
500222 Passive Ceiling Speaker
Safety Precautions
To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for future reference.
- Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
- Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
- Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
- To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near water. Keep the product away from liquids.
- Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
- Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
- Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.
- Refer all servicing to qualified service personnel.
- Install the device in a place with adequate ventilation to avoid damage caused by overheat.
- Unplug the power when left unused for a long period of time.
- Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.
Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or
translated without the express permission of MuxLab Inc. Product
specifications and information in this document are for reference only, and
the content may be updated from time to time without prior notice.
Introduction
The MuxLab Passive Ceiling Speaker 8 Ohms/70V/100V, 40W (Model: 500222) is a
high-performance full band and easy installation speaker ideal for providing
background music and vocal performance in a wide range of applications and
installations and is designed with advanced linear sound source technology.
This speaker can be used as an 8 ohm speaker at 40 W but can also be cascaded
when set as a 70V speaker system with taps at 2.5W, 5W, 10W and 20W, and as a
100V speaker system with taps at 5W, 10W, 20W and 40W.
The MuxLab Passive Ceiling Speaker 8 Ohms/70V/100V, 40W comes with a 6.25”
coaxial 40W loudspeaker driver that has excellent dispersion, wide bandwidth,
and smooth frequency response which makes this the top choice for today’s
overhead commercial and residential applications.
Features
- 40 Watts RMS
- Frequency Range 96Hz – 20KHz (+/- 3dB)
- Impedance 8Ω
- Tweeter 1” (25mm) Titanium Dome
- Woofer 6.25” (165mm) Graphite Cone, Rubber Surround
Package Contents
- One (1) Passive Ceiling Speaker 8 Ohms/70V/100V, 40W
- One (1) Speaker hole template
- One (1) Safety Wire Rope for Ceiling Speaker
- One (1) User manual (available via download)
Notes: Confirm that the product and accessories are all included. If not, please contact the supplier from which you purchased the unit.
Specifications
| Audio Input | Analog Audio Signal |
|---|---|
| Frequency Range +/- 3dB | 96Hz ~ 20KHz |
| Tweeter | 1” (25mm) Titanium Dome |
| Woofer | 6.25” (165mm) Graphite Cone, Rubber Surround |
| Power Handling RMS | 40W (IEEE 219) |
| Sensitivity (1W @ 1m) | 86dB |
| Crossover Frequency | 3.5 kHz |
| Conformity (Input) | 100V (8Ω) |
| Taps | 8Ω, 0, 40W, 20W, 10W, 5W |
| Impedance | 8Ω |
| Nominal Coverage | 90 degrees conical |
| Termination | Standard pressed connector |
| Attachment | Low-profile grille |
| Included Accessories | Cutout template grille |
| Dimension (H x D) | 236 x 257 mm (9.01” x 10.11”) |
| Weight | 3.3kg |
| Cut out diameter | 8.90” (226mm) |
| Material | ABS + iron |
| Shipping Weight | 8.0 lbs (3.6 kg) |
| Warranty | 2 years |
| Order Information | 500222 Passive Ceiling Speaker 8 Ohms/70V/100V, 40W |
(UPC: 627699002223)
Technical Drawings
Installation
STEP 1
Using a stud finder (available at low cost at most hardware stores) or other
accurate method, locate center point between two joists and mark. Using
template provided, trace hole pattern on surface of ceiling. STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in
ceiling. Following trace pattern.
STEP 3
Run loudspeaker wire to sound source location. There are several methods you
can use to accomplish wiring, depending on the construction characteristics of
the room or house. You can add a professional touch to your installation by
using a speaker terminal plate at the source location. Leave sufficient amount
of wire at speaker location (8-10 inches / 20-25 cm) to complete connection.
STEP 4
Attach loud speaker wire to speaker terminals observing correct polarity and
position speaker frame up into cutout. Be careful not pinch wires in the
process.
STEP 5
Carefully tighten the four mounting screws. This will cause the mounting wings
to rotate our behind the mounting surface and secure the speaker in place.
STEP 6
After the speaker panel is secured tightly, test sound. When you are satisfied
the speaker is operational, then affix grill. As grill is designed for a snug
fit you’ll need to position one edge into slot first and press or squeeze
around perimeter of grill, while pushing leading edges into grill slot.
Applications
The Passive Ceiling Speaker 8 Ohms/70V/100V, 40W are ideal for hotels,
conference rooms, shopping center, education, hospitals, retail stores,
performing art centers, restaurants, airports, houses of worship, and board
rooms.
Below you will find some diagrams showing the 500222 speakers as a solution in
different scenarios working together with other MuxLab devices.
Passive Ceiling Speaker 8 Ohms/70V/100V, 40W
500222
Follow us:
2321 Cohen | St-Laurent , H4R 2N7 | Québec, Canada
Tel:514-905-0588
Fax: **514-905-0589 | Toll free:
1-877-689-5228**
info@muxlab.com
salesteam@muxlab.com |
www.muxlab.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>