Stinger TXFBB12 Swing Gate Mounted Subwoofer Enclosure Installation Guide

INSTALLATION NOTES

• For models equipped with a factory subwoofer, unplugging the factory subwoofer is recommended.
• Some installation steps are more easily completed with a second person.
• Speaker wire is required before the enclosure is mounted.
• Recommended amplifier rating: 200-600 watts @ 2ohms.
• Do not power up until inside contents are removed.

GETTING STARTED

Remove the four Philips screws from the speaker and remove the speaker. Set speaker and screws in a safe place.

RECOMMENDED TOOLS

2 Philips Screwdriver

5mm Allen Wrench
14mm Wrench
10mm Socket

Ratchet
Socket Extension

9mm Drill Bit (Included)
Drill
Center Punch
Hammer
Tape
Wire Strippers

HARDWARE

• M6 FLANGED HEX HEAD BOLT (2) 40mm / 1.57in Length
  

• M6 ALLEN HEAD BOLT (4) 20mm / .78in Length
  

• M6 SPLIT LOCK WASHER (2) 11mm / .43in Diameter
  

• M6 METAL WASHER (3) 18mm / .71in Diameter
  

• M6 RUBBER WASHER (2) 18mm / .71in Length
  

• BOTTOM L BRACKET (2)
  

• FOAM BRACKET PAD (2)
  

• MOUNTING TEMPLATE (1)
  

• M6 HEX HEAD BOLT (2) 40mm / 1.57in Length
  

• M8 HEX NUT SPACE
  

• M6 TOOTH LOCK WASHER (2)
  

• M6 RIVET NUT INSERT (5)
  

• M5 PHILIPS HEAD SCREW (4 30mm /. 78in Length (Removed from speaker)
  

• M5 PHILIPS HEAD SCREW (6) 30mm / .78in Length (Included in hardware)
  

• POLY-FILL (1)
  

NOTE: Hardware images not to scale. There will be hardware left over depending on the installation

INSTALLATION

1. Using scissors or a straight edge and utility knife, cut out the template along the dashed lines.
   

2. Position the template on the on the inside of the swing gate using the plastic trim panel as a guide as shown.

Align the left and right cross-hairs on the template to the register marks on the trim panel (1). Verify the template is straight by confirming the horizontal line on the template (2) follows the horizontal groove on the plastic trim panel.

Once aligned, securley tape the template to the swing gate.

3. Using a center punch, mark the four mounting locations on the template Remove the template and drill pilot holes at the four locations.

CAUTION: To prevent the drill bit from hitting the outer side of the swing gate, wrap a significant amount of tape around the drill bit leaving only ½” of the bit exposed.

Drill 9mm holes at the four marked locations.

4. Remove the swing gate trim panel using a nylon panel tool or similar  to release the retaining clips (1) along the bottom, then swing up (2) to release the locking tabs along the top
   

5. If a rivet nut setter is not available, follow the directions below for each of the four holes:
   A. Insert a R1 rivet nut into the hole.
   B. Slide an W2 metal washer, a N1 spacer nut and a W4 tooth lock washer onto one of the B3 bolts.
   C. Hand thread the bolt into the rivet nut until it is hand tight.
   D. Using a 14mm wrench to hold the spacer nut, start tightening the bolt with a 10mm socket. Ensure the the rivet nut remains fully inserted and flat against the panel surface while tightening. The wrench and spacer nut should be held in place; do not rotate. The rivet nut takes approximately 12-13 quarter turns to propery seat. The bolt will get harder to turn when the rivet nut is seated.
   E. Once installed, loosen and remove  the 10mm bolt while continuing to hold the spacer nut in place with the wrench.
   
   NOTE: After installing the first rivet nut, ensure the side of the spacer nut that was positioned against the tooth lock washer is the same for the remaining installations.

There are two bolts, spacer nuts and washers provided in the event they are needed.
TIP: Having a second person hold the wrench in place and using two hands to tighten with the ratch – et will allow you to apply more forward pressure while tightening, keeping the insert flush against the panel.

6. In the two lower threaded inserts,install L1 brackets using B2 allen bolts.

Apply the L2 Foam Bracket Pads to the brackets.

7. Run a suitable length of speaker wire into the swing gate following the factory wire harness.
   Connect the speaker wire to the terminals. Positve (+) is Red and Negative (-) is Black. Route the speaker wire in the channel.
   

8. Align the speaker enclosure on the L Brackets. Loosley install the indicated hardware into the upper mounting holes from inside the enclosure.

Install the two B2 Allen Head Bolts through the L Brackets and into the bottom of the enclosure.

Once all the bolts are threaded, tighten all hardware

9. A. Place the sheet of poly-fill inside the enclosure along the back and side areas.
   B. Connect the speaker leadsinside the enclosure to either of the speaker terminals on the speaker. Positve (+) is Red and Negative (-) is Black.
   NOTE: Ensure the pre-installed speaker terminal jumper wires stay connected when connecting the wires to the speaker terminal.
   C. Align the speaker and install eight P1 screws securing the speaker.
   

SPECIFICATIONS

Height
17in / 43.2cm
Width
27.5in / 69.9cm
Depth
4.6in / 11.7cm

Stinger is a Power Brand of AAMP Global 15500 Lightwave, Clearwater, Florida 33760
Phone: 888-228-5560

Technical Support

Phone: 727-592-5991
Email: support@stingerelectronics.com
Chat: stingerelectronics.com

Stinger and the Stinger logo are trademarks or registered trademarks of AAMP Global in the United States and other countries.

AAMP Global is not affiliated with FCA US LLC. Jeep® is a registered trademark of FCA US LLC. The terms OEM, Jeep, Wrangler, and Gladiator all terms are used strictly for identification purposes only. It is not implied that any part listed is a product of, or approved by, Fiat Chrysler Automobiles.

© 2021-2023 AAMP Global. All rights reserved. | IG-TXFBB12 REV 082323

References

• Stinger - Define Your Drive
• SWING GATE-MOUNTED 12-INCH SUBWOOFER ENCLOSURE FOR FORD BRONCO – Stinger

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>