WAVLINK WL-WN573HX1 WiFi 6 Outdoor Mesh Router AP Repeater User Guide

WL-WN573HX1 WiFi 6 Outdoor Mesh Router AP Repeater
User Guide

Hardware Overview

1. 5G Antenna
2. 2.4G Antenna
3. Grounding Terminal
4. Status LED
5.  WANILAN Port (PoE)
6. Pair/Reset Button

Reset Button
Press and hold for 6 seconds to restore the device to default settings
Pair Button
Press and hold for 1 second to pair with the existing EasyJet Wi-Fi system

Default Parameters
2.4G $SID: WAVLINK-AX_XXXX
5G SSID: WAVLINK-AX_5G_XXXX Default IP: 192.168.10.1
Login: http://waplogin.link
Default Login Password: admin
Official Website: www.wavlink.com
Technical Support: support@wavlink.com
LED Indicator

but no access to the Internet.
Solid on| The device has connected to the upstream router and the Internet has been connected.
Fast blinking| The device has not connected to the upstream router.
Agent mode| Slow blinking| The device has connected to the upstream router but no access to the Internet.
Solid on| The device has connected to the upstream router and the Internet has been connected.
Fast blinking| The device has not connected to the upstream router.
AP mode| Solid on| The device has connected/disconnected to the Internet.

Installation

Assembly

1. ass the RJ45 cable through the waterproof connector cover
2. Screw the waterproof seal into the waterproof connector bracket
3. Pass the RJ45 cable through the waterproof connector bracket, and screw the waterproof connector bracket into the cover
4. Put the waterproof sealing ring on the waterproof connector bracket
5.  Connect the RJ45 cable to WAN/LAN port
6. 6Screw the connecting cable into the 24G and 5G antenna connector and screw up the connector

Note Turn the wrench counterclockwise during assembly to tighten the bracket; Turn the wrench clockwise to loosen the bracket during disassembly
Installation
2.1 Fix the device to the post with cable ties, or fix the device to the wall with screws, then follow the assembly step to install Note If it is installed in an area where lightning occurs frequently, we recommend you to install the device via a ground connection to strengthen the lightning protection function
2.2Connection
2.2.1 Passive PoE

1. Wired(For Router AP Mode)

2. Wireless(For Repeater/Mesh Agent Mode)

3. Connect the PoE” port of the PoE converter with an Ethernet cable to the WAN’LAN port of the device

4. Connect the LAN DATA IN” port of the POE converter via another Ethernet cable to a LAN port on your router If you choose to connect to the superior wireless/y, please ignore this step

5.  Plug the power plug into the DC IN(37-57V) port of the PoE converter, and then plug the power adapter into a power outlet

2. 2.2 Active PoE (For AP/Router Mode) Attention:

1. Make sure you are using a certified CAT5e/CAT6 Ethernet cable with R445 connectors
2. Make sure the Ethernet cable length is less than 100 meters(328 feet)
3. If it is fixed on the post, the length of the post must be less than the length of the cable ties

Configuration

Connecting to PC
1.1Via Wireless

1. Disconnect the Ethernet cable from your computer (if you have one)
2. Turn on your WiFi, find the $SID of this product on your wireless devices(smartphone, tablet computer, laptop, et.) and place a connection

1.2 Via Cable

1. Connect the Ethernet cable to your PC/Laptop and the LAN DATA IN port of your PoE converter, then you can start the configuration of the device
   If you are using the AP/Router function of this device, please connect the LAN DATA IN Port to the LAN port of the upper router after finishing 4.3 and 44.

2.  When the router is connected to your devices at its first time, the login page will pop up, you also can enter 192.168.10.1 or applagin link into the address bar of browser of your PC/atop or phone. The default password is admin.

3. Select your Country/Region and Time Zone. For your network security, we suggest that you set a new login password, and click Next.

Note: The three colored bars in Change Password area indicates the strength of the login password.
Mode Selection
This product has 4 modes
4.1 Repeater Mode
For Repeater mode, we recommend you to choose WI3p”_you can manually enter the WiFi SSID you need to connect or select the WiFi SSID in the list, and the Password needs to be the same as the WFi password that this product has connected, then click on Connect”

4.2 Easy Mesh Agent Mode
If you have a router that supports Easy Mesh function, then you can build a mesh system with this mode Please configure according to the following steps

1. Log in to 192.168.10.1 or waplogin.link
2.  In Mode Selection, please choose Easy Mesh Agent Mode
3.  Click on the Save” button
4.  Enter the Pair Key of this device in the mesh network of the main router, or you can separately keep pressing the Pair button on the main router and sub-router for 1 second

Note
If you are not sure how to start, please ask manufacturer for help
4.3AP Mode(LAN Bridge)
You can change the $SID or use the default one, as for the Encryption Mode, the default is WPA2-PSK, we recommend you to select WPA3WPA2-MIX if your devices support. For your network security, please set a new password according to the rule. Then click on Save” and wait for the setting process to complete. Note After the Smart DHCP service is enabled, the system automatically enables or disables the DHCP server based on the network environment If IP address conflict occurs on your local network, you can choose to disable Smart DHCP service, then the system will not automatically assign an IP address to the Router
4.4 Router Mode
If you choose the Router Mode, the system will guide you to select the WAN Type. As for the Encryption Mode, the default is WPA2-PSK, we recommend you to select WPA3WPA2-MIX if your devices support. For you network security, we suggest you set a Password. Which WAN Type am I supposed to choose?
If you use DSL line and you are only provided an account name and a password by your ISP, choose PPPoE If you use cable TV or fiber cable, choose DHCP(Dynamic IP).
If you are provided information such as IP address, Subnet Mask and Default Gateway, choose Static I

WI-Fl Password Mana ament

When you need to change your Wi Fi password, please click on Wireless

Firmware Upgrade

If you need to update firmware, please proceed as the following steps: Option

1. Download the latest firmware file on Weblink website (www.wavlink.com->SUppORT.>Firmware)
2.  Extract the firmware from the downloaded file
3. Log in to waplogin.link or 192.168.10.1, then choose Advanced and select Firmware Update
4. Click on[_ to locate the firmware file
5. Click on Upload and choose Apply, and wait for the firmware upgrade process to complete

Option II

1. Log in to 192.168.10.1 or waplogin.link, then choose Advanced and select Firmware Update
2. Click on Check New Version” to find the latest version
3.  Click on Download and Upgrade, and wait for the firmware upgrade process to complete

Note. After updating firmware, please Reset The Device And Clear Your Browser Cache.
What is firmware upgrade and why do I need it?
Firmware fixes bugs for your device, contains new features, and improves the experience of using the product. For your device update and security, please ask us for help, wrong upgrade may damage your device and void the product warranty
For more details, please visit our website www.wavlink.com and our technical support: support@wavlink.com

More Mesh Devices

Generally, a mesh router device supports up to (including the existing device) Therefore, if you need to add more mesh devices to build up a stable network in your home, you simply need to pair the new mesh devices with the existing network

1. Login to waplogin.link or 192.168.10.1
2. Advanced »> Mesh Network”
3. You can add extra devices by entering their Pair Key, and the sub-routers must be Mesh Agent Mode. You also can add extra devices by separately keeping pressing the Pair button for 1 second on the main router and sub-router after setting the sub-router as Easy Mesh Agent Mode

FAQ

Q1. Why doesn't the login page appear after entering http://waplogin.link?

- If your computer is wirelessly connected, please verify that you have connected to the device's $SID. If your computer is connected via an Ethernet cable, please verify that the connection is stable - Make sure your computer is set to obtain an IP address automatically - Use the IP address to log in to the page. The default IP is 192 168.10.1 If the device is connected to the host Wi-Fi, please go to the router's DHCP client list to obtain the device's current IP address - If the problem stll exists, please reset the device again

Q2. How do l restore the device to its factory default settings?

While the device is powered on, press and hold the Reset Button until all the LEDs turn on momentarily

Q3. What should I do if the LED does not change to solid after complet¬ing?

- You may have entered the incorrect Wi Fi password of your host Wi Fi during the configuration Please log into the device's web-based interface to check the password and try again - Reset the device and go through the configuration again

For more details, please refer to www.wavlink.com

GNU General Public License Notice

This product includes software codes developed by third parties. These software codes are subject to either the GNU General Public License (GPL), Version 2, June 1991 or the GNU Lesser General Public License (LGPL), Version 2.1,February 1999. You can copy, distribute, and/or modify in accordance with the terms and conditions of GPL Or LGPL
The source code should be complete, if you want us to provide any additional source code files under GNU General Public License (GPL), please contact us in these matters. We are committed to meeting the requirements of the GNU
General Public License (GPL). You are welcome to contact our local office to get the corresponding software and licenses Please inform us of your contact details (full address) and the product code We will send you a software package with the software and license for free
The respective programs are distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE
Please refer to the GNU General Public License website for further information http://www.gnu.org/licenses/old-licenses/lgpi-2.0.html http://www.gnu.org/licenses/gplhtmI
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household or general waste.
It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier tot disposal

WN573HX1  WAVLINK-E1

85×125 mm| 680×125 mm
105g
2023.01.09|

https://wavlink.com/en_us/AERIAL-HD6
Scan the QR code or load the link for
Quick Start Guide downloading
WAVLINK (@Wavlink Official)
WAVLINK SUPPORT (@Wavlink Tech Support)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>