Waterdrop WD-G2 Reverse Osmosis Water Filter User Guide

**Waterdrop WD-G2 Reverse Osmosis Water Filter User Guide

**

Quick Setup

Parts List

Identify and get familiar with all components according to the parts list for quick installation.

Note : If there are any parts cracked or broken, please do not proceed with the installation and contact Waterdrop by phone: 1-888-352-3558(U.S.) Mon-Fri 8:00 AM–5:00 PM (PST)

• RO System X 1 Set

• X 1 Set

• Feed Water Adapter 3/8 and 1/2

• White 3/8″ PE Tubing Preinstalled

• Drain Saddle 1/4″ X 1 Set

• White 1/4 PE Tubing X 59°

• Red 1/4″ PE Tubing X59

• Lock Clip X4

• Tedon Tape X1

Sample Connection

Quick Installation

Before installation, please note:

• The RO system must be connected to the COLD water supply ONLY.
• Do not install the system in exposure to direct sunlight or harmful chemicals, nor any place where it may be damaged.
• Do not install the system near any heat source, • Do not install the system outdoors.

Step 1 : Install the Feed Water Adapter (3/8″ or 1/2″)

• Shut off the water supply. Turn on the kitchen faucet to release the water pressure.
• Disconnect the cold water pipe from the cold water supply valve. • Twist the feed water adapter onto the cold water supply valve (with its washer) and tighten it with an adjustable wrench.
• Twist the cold water pipe (with its washer) onto the feed water adapter and tighten with an adjustable wrench.
  

Step 2: Install the RO Faucet (Non-Air Gap Faucet)

Note: If there is no hole in your kitchen sink or counter- top, you have to drill one (1″) or use the hole in the soap dispenser, Refer to the manual.

• Insert the faucet spout into the faucet body.
• Insert the faucet stem into the hole on the countertop.
• Under the sink, slip on other parts in the order shown in the picture.
• Insert the quick-connect fitting onto the faucet stem fully and firmly.

Step 3: Install the Drain Saddle

• Choose a spot on the drainpipe that is convenient for installing the drain saddle and drill a 1/4″ hole.
• Slip the front plate to one end of the tubing (without mark), and insert the tubing into the drilled hole up to about 0.6″.
• Fix the drain saddle with screws and install the lock clip on the fitting to secure the connection.

Step   4: Position the RO System Housing

Check and ensure there is sufficient space under the countertop to install the system.

Step 5:

• Connect the input water tubing from the feed water adapter to the “IN” input water port.
  

Note: Make sure each tubing is fully inserted until you reach the mark on the tubing.

• Connect the filtered water tubing from the RO faucet to the filtered water port.
  

• Connect the waste water tubing from the drain saddle to the “W” waste water port.

Step 6: Start up the System

• Turn on the cold water supply valve.
• Insert the power plug into the socket.
• Turn on the faucet to let water run for 30 minutes until the filtering indicator on the front panel changes from flashing to permanent blue.
• Confirm the 30-minute flushing is completed before turning off the RO faucet.

Display and Operation

Section 1: Working Mode Display When making water, the filter and power indicators are permanent blue. Filter life indicators display in real time and their color depends on their lifespan. Filtering indicator is off when the system stops making water, and the rest of the indicators are still on.

Section 2: Filter Life Reminder

There are helpful electronic filter indicators (CF/MRO) on the front panel that will notify you to perform routine filter replacement by color change. Be sure to reset the filter life indicator every time you replace your filter.

Display Status

Status| Remaining
Life (Day)| Remaining Capacity (G)| Indication| Status
---|---|---|---|---
Light| Buzzer
Normal| >15| >40| Blue| N/A| Good
Pre-waming| 15| <400| Purple| Beeps 2 times when
dispensing water| Replace Soon
Warning| =         0| Red| Keeps beeping when
dispensing water| Replace Now

Note: The indicators will notify you according to the usage time or processing capacity of the filters, whichever comes first.

Manufacturer Technical Support
Tel: 1-888-352-3558 (U.S.)
E-mail: service@waterdropfilter.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>