KEURIG K-Mini Plus Coffee Maker User Guide
- June 14, 2024
- Keurig
Table of Contents
KEURIG K-Mini Plus Coffee Maker
Product Information
This product is a coffee brewer that allows users to make hot beverages quickly and easily. It has features such as a power button, brew button, strong button, water reservoir, drip tray, and a handle for lifting and lowering. The brewer is designed to be easy to use and maintain, with a one- time setup process and regular cleaning recommended for optimal performance.
Specifications
- Power: Grounded outlet
- Water Capacity: 1 cup (8oz) minimum, 12oz maximum
- Cleaning Frequency: Regular cleaning recommended, descaling every 3-6 months
Product Usage Instructions
Before You Brew
- Remove packing tape from the brewer.
- Pull the plug and extend the cord from the cord storage located at the back of the brewer.
- Plug the brewer into a grounded outlet.
- Press the power button. The power button will illuminate.
Lift & Lower
Lift and lower the handle of the brewer. The STRONG indicator light will flash to indicate that the brewer is ready.
Fill & Place
- Add 1 cup (8oz) of water into a mug.
- Lift the water reservoir lid and pour the water into the reservoir. Do not fill past the MAX or below the MIN fill lines.
- Lower the lid and place your mug on the drip tray.
- Note: Do not use distilled water.
Cleansing Brew
- Press the brew button.
- The brew indicator light will illuminate solid, then begin to pulse while the brewer is heating.
- After about 2 minutes, the brew indicator light will illuminate solid again and the water will begin to dispense.
- Pour the hot water into the sink.
Brew Your First Cup
- Add the desired amount of water into a mug (6oz minimum, 12oz maximum).
- Lift the water reservoir lid and pour the water into the reservoir. Do not fill past the MAX or below the MIN fill lines.
- Lower the lid and place your mug on the drip tray.
Brew & Enjoy!
Press the brew button to start brewing. For a bolder coffee, press the STRONG button before pressing the brew button. The brew indicator light will illuminate solid, then begin to pulse while the brewer is heating. After about 2 minutes, the brew indicator light will illuminate solid again and the beverage will begin to dispense. Brewing is complete when the brew indicator light is no longer illuminated.
Lift & Place Pod
Lift the handle completely to close the lid. The brew indicator light will flash to indicate that the brewer is ready. Do not remove the pod.
Caring for your Brewer
Brewer Exterior
Regularly clean the exterior of your brewer with a damp, soapy, lint-free, non-abrasive cloth. Make sure to turn off and unplug the brewer before cleaning.
Drip Tray
The drip tray can hold up to 8 ounces of overflow and should be emptied and cleaned occasionally. To remove, slide it toward you, keeping it level to avoid spilling. Rinse and clean with a damp, soapy, lint-free, non-abrasive cloth.
Water Reservoir
The removable water reservoir should be cleaned periodically with a damp, soapy, non-abrasive cloth. Rinse the reservoir thoroughly after cleaning. Do not dry the inside of the water reservoir with a cloth as lint may remain. Allow the reservoir to dry completely.
Descaling your Brewer
Descaling your brewer every 3-6 months is recommended. Follow the descaling procedure provided by the manufacturer. Regular descaling helps maintain the heating element and other internal parts that come in contact with water.
Funnel
Refer to support.keurig.com for video instructions on cleaning the entrance/exit needles.
FAQ
Q: How often should I clean my brewer?
A: Regular cleaning is recommended to keep your brewer running smoothly. Clean the exterior regularly and clean the water reservoir periodically with a damp cloth.
Q: Can I use distilled water?
A: No, do not use distilled water in the brewer.
Q: How often should I descale my brewer?
A: It is recommended to descale your brewer every 3-6 months to maintain optimal performance. Follow the descaling procedure provided by the manufacturer.
Get the most from your new Keurig® brewer
Before You Brew
-
Plug & Power
Remove packing tape from brewer. Pull plug and extend cord from cord storage located at the back of the brewer. Plug into a grounded outlet.
Press the power button. The power button will illuminate. -
Fill & Place
Add 1 cup (8oz) of water into a mug. Lift the water reservoir lid and pour the water into the reservoir. Do not fill past the MAX or below the MIN fill lines. Lower the lid and place your mug on the drip tray.
NOTE: Do not use distilled water. -
Lift & Lower
Lift and lower the handle. Do not insert a K-Cup® pod. The brew indicator light will flash to indicate that the brewer is ready. -
Cleansing Brew
Press the brew button. The brew indicator light will illuminate solid, then begin to pulse while the brewer is heating. After about 2 minutes, the brew indicator light will illuminate solid again and the water will begin to dispense. Pour the hot water into the sink.
The one-time setup process is now complete and you are ready to brew! -
Fill & Place Mug
Add desired amount of water into a mug (6oz minimum, 12oz maximum). Lift the water reservoir lid and pour the water into the reservoir. Do not fill past the MAX or below the MIN fill lines. Lower the lid and place your mug on the drip tray. -
Lift & Place Pod
Lift the handle. Place a K-Cup® pod in the K-Cup® pod holder. Lower the handle completely to close the lid. The brew indicator light will flash to indicate that the brewer is ready. Do not remove the foil lid on the K-Cup® pod.
High Altitude Brewing: While holding the brewer handle up, push down slowly on the K-Cup® pod in the pod holder until the bottom of the K-Cup® pod is punctured by the exit needle. -
Brew & Enjoy!
Press the brew button – for bolder coffee, press the STRONG button before pressing the brew button. The brew indicator light will illuminate solid, then begin to pulse while the brewer is heating. After about 2 minutes, the brew indicator light will illuminate solid again and the beverage will begin to dispense. Brewing is complete when the brew indicator light is no longer illuminated. When complete, lift the handle and dispose of the used K-Cup® pod.
Brewer Features
- Strong Brew increases your coffee strength and intensity. For bolder coffee press the STRONG button.
- Pod Storage holds 9 K-Cup® pods and fits in your brewer to save counter space.
- Removable Water Reservoir for easy cleaning and filling.
- Auto Off: Automatically turns your brewer off 90 seconds after the last brew for energy savings.
- Cord Storage: Makes transporting your brewer convenient and keeps countertops tidy.
- Travel Mug Friendly: Remove the drip tray to accomodate a travel mug.
Caring for your Brewer
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
Brewer Exterior
Keep your Keurig® brewer looking its best by cleaning the exterior from time
to time. Just clean with a damp, soapy, lint-free, non-abrasive cloth. Never
immerse the brewer in water or other liquids.
Water Reservoir
The removable water reservoir should be cleaned periodically with a damp,
soapy, non-abrasive cloth. Rinse the reservoir thoroughly after cleaning. This
will ensure that no cleaning solutions remain in the area as they may
contaminate the water supply. Do not dry the inside of the water reservoir
with a cloth as lint may remain. Allow the reservoir to dry completely.
Drip Tray
The drip tray can hold up to 8 ounces of overflow and should be emptied and
cleaned occasionally. To remove, slide it toward you, keeping it level to
avoid spilling. Rinse and clean with a damp, soapy, lint-free, non-abrasive
cloth.
K-Cup® Pod Holder
To remove the K-Cup® pod holder from the brewer, lift the handle and grasp the
top of the K-Cup® pod holder with one hand while pushing up on the bottom of
the K-Cup® pod holder from underneath with the other until it releases. After
cleaning, align the K-Cup® pod holder with the opening using the two front
ribs as a guide and snap into place from the top.
CAUTION: There are sharp needles that puncture the K-Cup® pod above the
K-Cup® pod holder and in the bottom of the K-Cup® pod holder. To avoid risk of
injury, do not put your fingers in the K-Cup® pod holder.
NOTE: Always remove and dispose of the used K-Cup® pod after brewing.
Exit Needle
Remove the pod holder assembly and detach the funnel. Locate the exit needle
on the inside bottom of the K-Cup® pod holder. Insert a straightened paper
clip into the exit needle to loosen any coffee grounds.
Funnel
Washing the funnel ensures a fresh beverage experience. The funnel should be
washed regularly and can be removed from the K-Cup® pod holder by pulling on
it until it pops off. To replace it, orient the snaps to the indent and just
snap it back onto the K-Cup® pod holder.
Entrance Needle
Lift the brewer handle and locate the entrance needle on the underside of the
lid. To clean both holes in the needle, hold the brewer handle in the upward
position and with your other hand, carefully insert a straightened paper clip
into both holes. Gently move it around to loosen any coffee grounds. Lower the
handle completely and run two water-only brew cycles. Do not insert a K-Cup®
pod.
TIP: Refer to support.keurig.com for video instructions on cleaning the
entrance/exit needles.
Descaling your Brewer
- You should descale your brewer every 3-6 months. Properly follow the descaling procedure.
- Depending on the mineral content of your water, calcium deposits or scale may build up in your brewer. Scale is non-toxic but if left unattended can hinder brewer performance. Regularly descaling your brewer every 3-6 months helps maintain the heating element, and other internal parts that come in contact with water. Calcium deposits may build up faster, making it necessary to descale more often.
Descaling Procedure
Before you begin, you will need a large ceramic mug, fresh water, Keurig®
Descaling Solution, and access to a sink.
Do not use a paper cup. Ensure that there is no beverage pod in the K-Cup® pod
holder. Please allow approximately 45 minutes for the descaling procedure.
STEP 1: Cleansing Rinse
- Turn on your brewer.
- Pour one third (4.6oz) of the Keurig® Descaling Solution into the water reservoir then add fresh water to the 10oz fill level.
- Place a large ceramic mug on the drip tray plate.
- Lift and lower the handle but do not add a K-Cup® pod.
- Press the brew button.
- Once solution is dispensed, pour the contents into the sink.
STEP 2: Internal Tank Soak
- Repeat step 1, but when the brew indicator light turns solid, press the power button as the brewer starts to dispense.
- Let the brewer stand for at least 30 minutes.
- Press and hold the brew button until the solution begins to dispense. Continue to hold the button until all of the solution has been dispensed.
- Pour the contents of the mug into the sink.
STEP 3: Fresh Water Rinse
Repeat step 1 using 12oz of fresh water only. Do not add Keurig® Descaling Solution. Repeat this step two additional times. You may need to perform additional fresh water rinse cycles if you notice any residual taste.
NOTE: The cleaning action of Keurig® Descaling Solution may result in a “foam” dispensed from the brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added. If this occurs, you may see only a small or no output dispensed, followed by the sound of air blowing out. If this occurs:
- Turn off and unplug the brewer.
- If there is Keurig® Descaling Solution in the water reservoir, discard the contents, rinse the water reservoir thoroughly and refill with water.
- Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse cycle. The brewer should begin to function normally as the solution is rinsed out and the scale is removed. If problem persists, allow brewer to sit unplugged for at least 30 minutes before continuing with the rinse.
Troubleshooting
Grounds in Your Coffee
Grounds may have gathered in the exit or entrance needles and can be cleaned
using a straightened paper clip or similar tool.
- Clean the exit needle of the K-Cup® pod holder. Refer to the Exit Needle care instructions.
- Clean the brewer entrance needle. Refer to the Entrance Needle care instructions.
Brewer Will Not Brew
A minimum of 6oz of water is required to brew. Add an additional 2oz of water
to the reservoir to ensure the minimum fill level has been met, then press the
brew button. Repeat until the brewer begins to dispense.
Brewing a Partial Cup
- Press the power button. Press and hold the brew button for 5 seconds until all of the water has been dispensed. Discard the contents into the sink. Press the power button to restart.
- The exit needle may be clogged. Refer to the Exit Needle care instructions.
- Clean the K-Cup® Pod Holder, see K-Cup® Pod Holder care instructions.
- The brewer may need to be descaled. If you have repeated the descale procedure on your brewer two times and it is still only brewing a partial cup, contact Customer Service.
Brewer Does Not Have Power or Shuts Off
- Make sure that the power button has been turned on.
- Plug brewer into its own grounded outlet. If the electric circuit is overloaded with other appliances, your brewer may not function properly. The brewer should be operated on its own circuit, separate from other appliances.
- For energy savings, the brewer automatically turns off 90 seconds after the last brew. Press the power button to restart.
- If the brewer still doesn’t have power, contact Customer Service.
Helpful Hints
Water quality varies greatly. If you notice an undesirable taste in your
beverage (such as chlorine or mineral tastes), we recommend using bottled or
filtered water. Do not use distilled water.
Service
Beyond these recommended cleaning and maintenance procedures, this brewer is
not user serviceable. For service, please refer to the Warranty section of
this guide.
Storage
Empty the water reservoir before storing or transporting and take care to
ensure that you store your brewer in a safe and frost free environment. When
you prepare to use it after storage, we recommend rinsing the water reservoir
with fresh water and descaling the brewer as detailed in the Descaling your
Brewer section.
If you plan to move your brewer to a different location, turn the brewer off,
unplug it, and empty the water reservoir.
Click or Call!
Have Questions?
We’re here to help. Visit support.keurig.com for step-by-step videos on
cleaning, descaling, and more.
Still Need Help?
Give us a call at If your brewer has been in an environment below freezing,
please be sure to let it warm to room temperature for at least 2 hours before
using. 1-866-901-BREW (2739)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>