Insmart YXY-801 Cordless Water Dental Flosser Teeth Cleaner Instruction Manual
- November 23, 2023
- INSMART
Table of Contents
- YXY-801 Cordless Water Dental Flosser Teeth Cleaner
- Product Information
- Specifications
- 1. Preventing Splashing
- 2. Troubleshooting – No Water Squirting Out
- 3. Pressure Settings
- 4. Changing Flosser Tips
- 5. Ensuring Longer Service Life
- 6. Installation and Removal of Jet Tips
- Q: My flosser has stopped working. What should I do?
- Q: Why is no water squirting out of my flosser?
- Q: What is the best pressure setting for the water
- Q: How do I change flosser tips?
- Q: How can I ensure a longer service life for my flosser?
- Q: How do I install and remove jet tips?
- Q: The red light flashes quickly while charging. What should I
YXY-801 Cordless Water Dental Flosser Teeth Cleaner
Product Information
Specifications
- Warranty Period: 1 year
- Pressure Settings: Normal, Soft, Pulse, DIY
- Adapter Requirement: 5V/1A
Product Usage Instructions
1. Preventing Splashing
To prevent splashing water everywhere, follow these steps:
-
Put the water flosser in your mouth before switching it
on. -
Partially close your lips enough to prevent splashing.
-
Allow the water to flow into the sink.
-
Keep the unit upright for continuous water flow.
-
Switch off the flosser before pulling it out of your mouth when
finished.
2. Troubleshooting – No Water Squirting Out
If no water is squirting out, try the following steps:
-
Fill the water tank.
-
Long press the release button to take out the jet tip.
-
Fill some water into the hole until water comes out from the
water pipe. -
Try using the water flosser again.
3. Pressure Settings
This water flosser comes with 3 pressure settings: Normal, Soft,
Pulse, DIY. For new users, it is recommended to start with the soft
mode to avoid gum discomfort. Filling the water tank with warm
water can enhance the experience.
4. Changing Flosser Tips
To change flosser tips, follow these steps:
- Locate the button on the water flosser machine.
- Press the button on the machine to remove the tip.
- Insert or take out the tip carefully to avoid it getting stuck
in the machine.
5. Ensuring Longer Service Life
To ensure a longer service life for your water flosser, follow
these guidelines:
-
Do not use the charger in a shower stall or any area with
running water that can come in direct contact with the
charger. -
Avoid using a strong (high current) charger or overcharging the
machine. -
If using an adapter, make sure it is 5V/1A. Using an adapter
plug greater than 7V may trigger Over Voltage Protection and
prevent charging.
6. Installation and Removal of Jet Tips
To install and remove jet tips, follow these steps:
-
Insert the jet tip into the jet tip mounting hole until you
hear a click, indicating installation completion. -
To remove the jet tip, long press the release button of the jet
tip and pull it upward at the same time. -
Note: Avoid pressing the release button of the jet tip during
use to prevent accidental injury from the jet tip ejecting.
Frequently Asked Questions
Q: My flosser has stopped working. What should I do?
A: The worldwide warranty period is 1 year. Please contact our
team through Your Account > Your Orders > Find your order and
click on Contact.
Q: Why is no water squirting out of my flosser?
A: Try filling the water tank, long pressing the release button
to fill water into the pipe, and then try using the water flosser
again.
Q: What is the best pressure setting for the water
flosser?
A: The water flosser comes with 3 pressure settings. For new
users, it is recommended to start with the soft mode. Filling the
water tank with warm water can enhance the experience.
Q: How do I change flosser tips?
A: Every water flosser has a button on the machine for removing
the tip. Make sure to press the button on the machine before
inserting or taking out the tip to avoid it getting stuck.
Q: How can I ensure a longer service life for my flosser?
A: Avoid using the charger in a shower stall or any area with
running water that can come in direct contact with the charger.
Also, do not use a strong (high current) charger or overcharge the
machine. If using an adapter, make sure it is 5V/1A.
Q: How do I install and remove jet tips?
A: To install a jet tip, insert it into the jet tip mounting
hole until you hear a click. To remove a jet tip, long press the
release button and pull it upward at the same time.
Q: The red light flashes quickly while charging. What should I
do?
A: Please replace the adapter to charge if the red light is
flashing quickly.
Frequently Asked Questions
Frequently Asked Questions
My flosser has stopped working The worldwide warraty period is 1 year. Contact
the team: “Your Account”> “Your Orders ” > Find your order and click on
“Contact”.
Splashing water everywhere? Put the water flosser in your mouth before you
switch it on and partially close lips enough to prevent splashing, let water
flow into sink. Keep unit upright for continuous water flow. Switch it off
before pulling it out of the mouth when finished.
No water is squirting out? Please try below: 1. Fill the water tank. 2. Long
press the release button, take out the jet tip, and fill some water into the
hold until water came out from the water pipe. 3. Try to use the water flosser
again.
Best pressure setting? This water flosser comes with 3 pressure
settings(Normal, Soft , Pulse, DIY). Some people may experience that their
gums hurt while using water flosser for the first time. Be cautious and we
recommend new users start with soft mode. ( Fill it with warm water would be
better.)
How do I change flosser tips? Every water flosser has a button on the machine,
which allows you to remove the tip. Please make sure to press the button on
the machine before inserting or taking out the tip, otherwise, it will be
easily stuck into the machine.
Longer service life? Don’t use the charger in a shower stall or other area
with running water that can come in direct contact with the charger. Don’t use
a strong (high current) charger or overcharger the machine.If you want to use
a adapter, you need to use 5V/1A. Any adapter plug greater than 7V may trigger
Over Voltage Protection and the unit will not charge.
Installation and removal of jet tips 1. Insert the jet tip into the jet tip
mounting hole; upon hearing “click” , the installation is completed 2. Long
press the release button of the jet tip and pull out the jet tip upward at the
same time to remove the jet tip Note: Do not press the release button of the
jet tip in the process of use, in order to avoid accidental injury by jet tip
ejecting
If the red light flashes quickly while charging, please replace the adapter to charge.