MSI G274QRFW Esports Gaming Monitor User Guide

June 14, 2024
MSI

MSI G274QRFW Esports Gaming Monitor

MSI-G274QRFW-Esports-Gaming-Monitor-product

Getting Started

This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.

Package Contents
Monitor G274QRFW
Documentation Quick Start Guide

Accessories

| Stand with Screw(s)
Stand Base with Screw(s)
External Power Supply
Power Cord
Cables| HDMI Cable (Optional)
DisplayPort Cable (Optional)

Important

  • Contact your place of purchase or local distributor if any of the items are damaged or missing.
  • Package contents may vary by country.
  • The included power cord is exclusively for this monitor and should not be used with other products.

Installing the Monitor Stand

  1. Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor groove.
  2. Tighten the stand bracket with screws.
  3. Connect the base to the stand and tighten the base screw to secure the base.
  4. Make sure the stand assembly is properly installed before setting the monitor upright.

Important

  • Place the monitor on a soft, protected surface to avoid scratching the display panel.
  • Do not use any sharp objects on the panel.
  • The groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for a proper wall-mount kit.
  • This product comes with NO protective film to be removed by the user! Any mechanical damages to the product including removal of the polarizing film may affect the warranty!

MSI-G274QRFW-Esports-Gaming-Monitor-FIG-3

Adjusting the Monitor

This monitor is designed to maximize your viewing comfort with its adjustment capabilities.
Important

  • Avoid touching the display panel when adjusting the monitor.
  • Please slightly tilt the monitor slightly before pivoting it.

MSI-G274QRFW-Esports-Gaming-Monitor-FIG-4

Monitor Overview

MSI-G274QRFW-Esports-Gaming-Monitor-FIG-5

1| Power LED

Lit in white after the monitor is turned on. If no signal is input, the LED will turn orange. Lit in orange when the monitor is in Stand-by mode.

---|---
2| Power Button & Navi Key
3| Cable Routing Hole
4| Power Jack
5| Headphone Jack
6| HDMI Port
7| DisplayPort

Connecting the Monitor to the PC

  1. Turn off your computer.
  2. Connect the video cable from the monitor to your computer.
  3. Assemble the external power supply & power (Figure A)
  4. Connect the external power supply to the monitor power (Figure B)
  5. Plug the power cord into the electrical (Figure C)
  6. Turn on the (Figure D)
  7. Power on the computer and the monitor will auto-detect the signal source.

OSD Setup

This chapter provides you with essential information on OSD Setup.

Important
All information is subject to change without prior notice.

Navi Key
The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu.

Up/Down/Left/Right:

  • selecting function menus and items
  • adjusting function values
  • entering into/exiting from function menus

Press (OK):

  • launching the On-Screen Display (OSD)
  • entering submenus
  • confirming a selection or setting

Hot Key

  • Users may enter into preset function menus by moving the Navi Key up, down, left, or right when the OSD menu is inactive.
  • Users may customize their own Hot Keys to enter into different function menus.

OSD Menus

MSI-G274QRFW-Esports-Gaming-Monitor-FIG-8

Important

The following settings will be grayed out when HDR signals are received:

  • Night Vision
  • MPRT
  • Low Blue Light
  • HDCR
  • Brightness
  • Contrast
  • Color Temperature
  • PIP/PBP
Gaming
1st Level Menu 2nd/3rd Level Menu Description
Game Mode User ∙ Use the Up or Down Button to select and preview mode

effects.

∙ Press the OK Button to confirm and apply your mode type.

FPS
Racing
RTS
RPG
1st Level Menu| 2nd/3rd Level Menu| Description
---|---|---
Night Vision| OFF| ∙ This function optimizes background brightness and is recommended for FPS games.
Normal
Strong
Strongest
A.I.
Response Time| Normal| ∙ Response time will be grayed out while MPRT is enabled.
Fast
Fastest
MPRT| OFF| ∙ When MPRT is enabled, Brightness cannot be enabled and will be grayed out.

∙ HDCR and MPRT cannot be enabled simultaneously.

∙ MPRT is available when the refresh rate is over 85Hz.

∙ MPRT has to be disabled while Adaptive-Sync is set to ON.

ON
Refresh Rate| Location| Left Top| ∙ Location is adjustable in OSD Menu. Press the OK Button to confirm and apply your Refresh Rate Location.

∙ This monitor follows and works at the Operating System’s preset Screen Refresh Rate.

Right Top
Left Bottom
Right Bottom
Customize
OFF
ON
1st Level Menu| 2nd/3rd Level Menu| Description
---|---|---
Alarm Clock| Location| Left Top| ∙ After setting the time, press the OK Button to activate the timer.

∙ Users have to manually restore their preset Alarm Clock after any AC power loss and reconnection.

Right Top
Left Bottom
Right Bottom
Customize
OFF
15:00| 00:01 ~

99:59

30:00
45:00
60:00
Screen Assistance| None| ∙ Users can adjust Screen Assistance in any mode.
Icon| ****



Adaptive-Sync| OFF| ∙ Adaptive-Sync prevents screen tearing.
ON

Professional
1st Level Menu 2nd Level Menu Description
Pro Mode User ∙ Use Up or Down Button to select and preview mode effects.

∙ Press the OK Button to confirm and apply your mode type.

∙ The default setting “Eco” mode meets the requirements of TÜV Rheinland’s “Low Blue Light (Hardware Solution)” standard and Eyesafe certification.

Anti-Blue
Movie
Office
sRGB
Eco
1st Level Menu| 2nd Level Menu| Description
---|---|---
Low Blue Light| OFF| ∙ Low Blue Light protects your eyes against blue light. When enabled, Low Blue Light adjusts the screen color temperature to a more yellow glow.

∙ When Pro Mode is set to Anti-Blue, it is mandatory to enable Low Blue Light.

∙ This monitor is a Low Blue Light backlight monitor, it would decrease the blue light emitted without adjusting OSD function.

ON
HDCR| OFF| ∙ HDCR enhances image quality by increasing the contrast of images.

∙ When HDCR is set to ON, Brightness will be grayed out.

∙ HDCR and MPRT cannot be enabled simultaneously.

ON
MPRT| OFF| ∙ When MPRT is enabled, Brightness cannot be enabled and will be grayed out.

∙ HDCR and MPRT cannot be enabled simultaneously.

∙ MPRT is available when the refresh rate is over 85Hz.

∙ MPRT has to be disabled while Adaptive-Sync is set to ON.

ON
Image Enhancement| OFF| ∙ Image Enhancement enhances image edges to improve their acutance.
Weak
Medium
Strong
Strongest

Image
1st Level Menu 2nd/3rd Level Menu Description
Brightness 0-100 ∙ Properly adjust Brightness according to the surrounding

lighting.

∙ Brightness will be grayed out when MPRT or HDCR are enabled.

1st Level Menu 2nd/3rd Level Menu Description
Contrast 0-100 ∙ Properly adjust Contrast to relax your eyes.
Sharpness 0-5 ∙ Sharpness improves clarity and details of images.
Color Temperature Cool ∙ Use Up or Down Button to select and preview mode

effects.

∙ Press the OK Button to confirm and apply your mode type.

Normal
Warm
Customization| R (0-100)
G (0-100)
B (0-100)
Screen Size| Auto| ∙ Users can adjust Screen Size in any mode, any resolution, and any screen refresh rate.
4:3
16:9
1:1

Input Source
1st Level Menu 2nd Level Menu Description
HDMI1 ∙ Users can adjust the Input Source in any mode.

HDMI2
DP
Auto Scan| OFF| ∙ Users can use the Navi Key to select Input Source at below status:

• While “Auto Scan” is set to “OFF” with the monitor at power saving mode;

• While the “No Signal” message box is shown on the monitor.

ON

PIP/PBP
1st Level Menu 2nd/3rd Level Menu Description
OFF ∙ Enabling PIP (Picture in Picture) or PBP (Picture by Picture) will

affect

• Response Time

• Adaptive-Sync

• MPRT

• Screen Size 1:1

• HDMI CEC

∙ Display Switch allows users to switch between primary and secondary input sources.

∙ If there is only one signal input, the Display Switch and Audio Switch will be grayed out.

PIP| Source| HDMI1
HDMI2
DP
PIP Size| Small
Medium
Large
Location| Left Top
Right Top
Left Bottom
Right Bottom
Customize
Display Switch
Audio Switch
PBP| Source 1| HDMI1
HDMI2
DP
Source 2| HDMI1
HDMI2
DP
Display Switch
Audio Switch

1st Level Menu 2nd Level Menu Description
Up Down Left Right OFF ∙ All Navi Key items can be adjusted via OSD Menus.

Brightness
Game Mode
Screen Assistance
Alarm Clock
Input Source
PIP/PBP Mode
Refresh Rate
Info. On Screen
Night Vision

Setting
1st Level Menu 2nd Level Menu Description
Language 繁體中文 ∙ Users have to press the OK Button to confirm and apply the

Language setting.

∙ Language is an independent setting. Users’ own language settings will override the factory default. When users set Reset to Yes, Language will not be changed.

English
Français
Deutsch
Italiano
Español
한국어
日本語
Русский
Português
简体中文
Bahasa Indonesia
Türkçe
(More languages coming soon)
1st Level Menu| 2nd Level Menu| Description
---|---|---
Transparency| 0~5| ∙ Users can adjust Transparency in any mode.
OSD Time Out| 5~30s| ∙ Users can adjust OSD Time Out in any mode.
RGB LED| Red| ∙ RGB LED offers unique lighting effects for your monitor.
Green
Blue
White
Breathing
Marquee
Rainbow
OFF
Power Button| OFF| ∙ When set to OFF, users can press the power button to turn off the monitor.
Standby| ∙ When set to Standby, users can press the power button to turn off the panel and backlight.
Info. On Screen| OFF| ∙ The information on the monitor status will be shown on the right side of the screen.
ON
DP

Overclocking

| OFF| ∙ To overclock the monitor refresh rate, users have to set DP OverClocking to ON.
ON
1st Level Menu| 2nd Level Menu| Description
---|---|---
HDMI CEC| OFF| ∙ HDMI CEC (Consumer Electronics Control) supports Sony PlayStation®, Nintendo® Switch™, Xbox Series X|S consoles, and various audio- visual devices that are CEC-capable.

∙ If HDMI CEC is set to ON:

• The monitor will automatically power on when the CEC device is turned on.

• The CEC device will enter power-saving mode when the monitor is turned off.

• When Sony PlayStation®, Nintendo® Switch™, or Xbox Series X|S console is connected, Game Mode and Pro Mode will be automatically set to default modes and can be adjusted to users’ preferred modes later.

ON
Reset| YES| ∙ Users can Reset and restore settings to the original OSD Default in any mode.
NO

Specifications

Monitor G274QRFW
Size 27 inch
Curvature Flat
Panel Type Rapid IPS
Resolution 2560 x 1440
Aspect Ratio 16:9
Brightness 300 nits (typ.)
Contrast Ratio 1000:1
Refresh Rate 170Hz
Response Time 1ms (GTG)
MPRT 1ms
I/O ∙ Power Jack x1

∙ Headphone Jack x1

∙ HDMI Port x2

∙ DisplayPort x1

View Angles| 178°(H) , 178°(V)
*DCI-P3/ sRGB| 90%/125%
Surface Treatment| Anti-glare
Display Colors| 1.07B (8bit + FRC)
Monitor Power Options| 19V     2.58A
External Power Supply| 49W, 19V
Power Input| 100~240Vac, 50~60Hz
Power Output| 19V     2.58A
Adjustment (Height)| 0 ~ 130mm
Adjustment (Tilt)| -5° ~ 20°
Adjustment (Swivel)| -45° ~ 45°
Adjustment (Pivot)| -90° ~ 90°
Kensington Lock| Yes
Monitor| G274QRFW
---|---
VESA Mounting**| ∙ Plate Type: 75 x 75 mm

∙ Screw Type: M4 x 10 mm

• Thread Diameter: 4 mm

• Thread Pitch: 0.7 mm

• Thread Length: 10 mm

Dimension (W x H x D)| 613.49 x 532.08 x 196.48 mm
Weight| 6.0 Kg (Net)

8.1 Kg (Gross)

Environment| Operating| ∙ Temperature: 0℃ to 40℃

∙ Humidity: 20% to 90%, non-condensing

∙ Altitude: 0 ~ 5000m

Storage| ∙ Temperature: -20℃ to 60℃

∙ Humidity: 10% to 90%, non-condensing

Preset Display Modes

Important

All information is subject to change without prior notice

Standard Resolution G274QRFW
HDMI DP
VGA 640×480 @60Hz
@67Hz V V
@72Hz V V
@75Hz V V
Dos-Mode 720×480 @60Hz
720×576 @50Hz V
SVGA 800×600 @56Hz
@60Hz V V
@72Hz V V
@75Hz V V
XGA 1024×768 @60Hz
@70Hz V V
@75Hz V V
SXGA 1280×1024 @60Hz
@75Hz V V
WXGA+ 1440×900 @60Hz
WSXGA+ 1680×1050 @60Hz
QHD 2560×1440 @60Hz
@120Hz V V
@144Hz V V
@165Hz V
@170Hz V *
Video Timing Resolution 720P V
1080P @60Hz V
@120Hz V V
2160P @30Hz V
@60Hz V
PBP Mode 1280×1440 @60Hz V

Users have to set DP OverClocking to ON. This is the highest refresh rate supported by DP OverClocking. If any monitor error occurs during overclocking, please downscale the refresh rate.

Troubleshooting

The power LED is off.

  • Press the monitor power button again.
  • Check if the monitor power cable is properly connected.

No image.

  • Check if the computer graphics card is properly installed.
  • Check if the computer and monitor are connected to electrical outlets and are turned on.
  • Check if the monitor signal cable is properly connected.
  • The computer may be in Standby mode. Press any key to activate the monitor.

The screen image is not properly sized or centered.

  • Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.

No Plug and play.

  • Check if the monitor power cable is properly connected.
  • Check if the monitor signal cable is properly connected.
  • Check if the computer and graphics card are Plug & Play compatible.

The icons, font, or screen are fuzzy, blurry, or have color problems.

  • Avoid using any video extension cables.
  • Adjust brightness and contrast.
  • Adjust RGB color or tune color temperature.
  • Check if the monitor signal cable is properly connected.
  • Check for bent pins on the signal cable connector.

The monitor starts flickering or shows waves.

  • Change the refresh rate to match the capabilities of your monitor.
  • Update your graphics card drivers.
  • Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).

Safety Instructions

  • Read the safety instructions carefully and thoroughly.
  • All cautions and warnings on the device or User Guide should be noted.
  • Refer servicing to qualified personnel only.
Power
  • Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet.
  • If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed main socket outlet.
  • Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).
  • Always disconnect the power cord or switch the wall socket off if the device is left unused for a certain time to achieve zero energy consumption.
  • Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
  • If this device comes with an adapter, use only the MSI-provided AC adapter approved for use with this device.
Battery

Please take special precautions if this device comes with a battery.

  • The a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
  • Avoid disposal of a battery in a fire or a hot oven, or mechanically crushing or cutting off a battery, which can result in an explosion.
  • Avoid leaving a battery in an extremely high temperature or extremely low air pressure environment that can result in an explosion or the leakage of flammable liquid or gas.
  • Do not ingest the battery. If the coin/button cell battery is swallowed, it can cause severe internal burns and can lead to death. Keep new and used batteries away from children.

European Union:
Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with local regulations.

Taiwan:
For better environmental protection, waste batteries should be collected separately for recycling or special disposal.

California, USA:
The button cell battery may contain perchlorate material and requires special handling when recycled or disposed of in California. For further information please visit: https://dtsc.ca.gov/perchlorate/

Environment
  • To reduce the possibility of heat-related injuries or overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.
  • Use this device only on a hard, flat, and steady surface.
  • To prevent the device from tipping over, secure the device to a desk, wall, or fixed object with an anti-tip fastener that helps to properly support the device and keep it safe in place.
  • To prevent fire or shock hazards, keep this device away from humidity and high temperature.
  • Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.
  • The maximum operating temperature is around 40℃.
  • When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemicals to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.
  • Always keep strong magnetic or electrical objects away from the device.

If any of the following situations arise, get the device checked by service personnel:

  • The power cord or plug is damaged.
  • Liquid has penetrated into the device.
  • The device has been exposed to moisture.
  • The device does not work well or you can not get it working according to the User Guide.
  • The device has dropped and is damaged.
  • The device has obvious signs of breakage.

TÜV Rheinland Certification

TÜV Rheinland Low Blue Light Certification

Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light.

  • Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.
  • Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.
  • Take breaks for 20 minutes every 2 hours.
  • Look away from the screen and gaze at a distant object for at least 20 seconds during breaks.
  • Make stretches to relieve body fatigue or pain during breaks.
  • Turn on the optional Low Blue Light function.
TÜV Rheinland Flicker Free Certification
  • TÜV Rheinland has tested this product to ascertain whether the display produces visible and invisible flicker for the human eye and therefore strains the eyes of users.
  • TÜV Rheinland has defined a catalog of tests, which sets out minimum standards at various frequency ranges. The test catalog is based on internationally applicable standards or standards common within the industry and exceeds these requirements.
  • The product has been tested in the laboratory according to these criteria.
  • The keyword “Flicker Free” confirms that the device has no visible and invisible flicker defined in this standard within the range of 0 – 3000 Hz under various brightness settings.
  • The display will not support Flicker-Free when Anti Motion Blur/MPRT is enabled. (The availability of Anti Motion Blur/MPRT varies by product.)

Regulatory Notices

CE Conformity

This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of the Official Journal of the European Union.

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/television technician for help.

Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notice 2
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

MSI Computer Corp. 901 Canada Court, City of Industry, CA 91748, USA

WEEE Statement

Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.

Chemical Substances Information

In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides information on chemical substances in products at: https://csr.msi.com/global/index

RoHS Statement

Japan JIS C 0950 Material Declaration

A Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006. https://csr.msi.com/global/Japan-JIS-C-0950-Material-Declarations

India RoHS

This product complies with the “India E-waste (Management and Handling) Rule 2016” and prohibits the use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

Turkey EEE Regulation

Conforms to the EEE Regulations of the Republic Of Turkey

Ukraine Restriction of Hazardous Substances

The equipment complies with the requirements of the Technical Regulation, approved by the Resolution of Cabinet of the Ministry of Ukraine as of 10 March 2017, № 139, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.

Vietnam RoHS

As of December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.

Green Product Features
  • Reduced energy consumption during use and stand-by
  • Limited use of substances harmful to the environment and health
  • Easily dismantled and recycled
  • Reduced use of natural resources by encouraging recycling
  • Extended product lifetime through easy upgrades
  • Reduced solid waste production through a take-back policy
Environmental Policy
  • The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
  • Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products.
  • Visit the MSI website and locate a nearby distributor for further recycling information.
  • Users may also reach us at gpcontdev@msi.com for information regarding proper disposal, take-back, recycling, and disassembly of MSI products.

Warning! Overuse of screens is likely to affect eyesight.

Recommendations:

  1. Take a 10-minute break for every 30 minutes of screen time.
  2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.

Copyright and Trademarks Notice

Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.

Technical Support

If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively, please visit https://www.msi.com/support/ for further guidance.

FAQs

What is the screen size of the MSI G274QRFW Esports Gaming Monitor?

The MSI G274QRFW features a 27-inch display, providing an immersive gaming experience with a good balance of size and clarity.

What is the refresh rate of this gaming monitor?

The monitor boasts a high refresh rate of 165Hz, ensuring smooth and responsive gameplay for esports enthusiasts.

Does the MSI G274QRFW support AMD FreeSync technology?

Yes, the monitor supports AMD FreeSync technology, reducing screen tearing and stuttering for a smoother gaming experience.

What is the resolution of the MSI G274QRFW monitor?

The monitor features a QHD (2560 x 1440) resolution, delivering sharp and detailed visuals for gaming and multimedia content.

Is the G274QRFW monitor compatible with G-Sync technology?

Yes, the monitor is G-Sync compatible, providing adaptive sync technology for NVIDIA graphics cards to enhance gaming performance.

What is the response time of this gaming monitor?

The MSI G274QRFW boasts a rapid response time of 1ms, minimizing motion blur and ghosting for fast-paced gaming scenarios.

Does the monitor have customizable RGB lighting?

Yes, the monitor features customizable RGB lighting on the back, allowing users to personalize their gaming setup with vibrant lighting effects.

What connectivity options are available on the MSI G274QRFW?

The monitor provides versatile connectivity with HDMI, DisplayPort, and USB ports, ensuring compatibility with various gaming devices.

Can I mount the MSI G274QRFW on a wall or monitor arm?

Yes, the monitor is VESA mount compatible, enabling users to mount it on a wall or use a monitor arm for flexible placement.

Does the G274QRFW monitor have built-in speakers?

No, the monitor does not have built-in speakers. Users can connect external speakers or use headphones for audio output.

Is the G274QRFW suitable for professional color-critical work?

Yes, the monitor features a high-quality IPS panel with accurate color reproduction, making it suitable for color-critical tasks and content creation.

Does the MSI G274QRFW support HDR (High Dynamic Range)?

Yes, the monitor supports HDR for enhanced contrast and a wider range of colors, providing a more immersive gaming and multimedia experience.

What is the warranty period for the MSI G274QRFW Esports Gaming Monitor?

The monitor typically comes with a standard limited warranty. For specific details, users should refer to the warranty information provided by MSI.

Download this PDF Link:MSI G274QRFW Esports Gaming Monitor User Guide

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals