Miele PG 8056-1 U Built Under Fresh Water Dishwasher Instruction Manual
- June 14, 2024
- Miele
Table of Contents
Miele PG 8056-1 U Built Under Fresh Water Dishwasher
Product Information
Specifications
-
Model : PG 8055 – PG 8099
-
Installation Plan : Available in multiple languages
-
Product Number : M.-Nr. 11 768 930
-
Electrical Connection:
-
EU, CH, CN, RU, U A, KZ: 3N AC 400 V/50 Hz, 8.9 kW, 3 x 16 A,
1.7 m -
BE, NO: 3N AC 400 V/50 Hz, 8.9 kW, 3 x 15-16 A, 1.8 m
-
AU: 3N AC 400 V/50 Hz, 5.9 kW, 1 x 30-32 A, 1.9 m
-
US, CA: AC 230 V/50 Hz, 3.4 kW, 1 x 16 A, 1.7 m
-
-
Water Connection:
- Cold Water: 0 – 60 mm
- Weight: 62.5 kg
- Noise Level: 47 dB
-
Dosage:
- Internal Dosage Pump (DOS): 0.35 kWh
- External Dosage Pump: 0.40 kWh
Product Usage Instructions
Installation
For safe installation and commissioning of the dishwasher, please read the
installation plan, the service documentation, and the operating instructions.
This installation plan includes the dimensions of the appliance, the technical
data, and the requirements to be met on site for the installation of the
dishwasher.
Installation Requirements:
- This dishwasher must be installed by an authorized technician.
- Installation must be done in accordance with all applicable standards and guidelines, including legal requirements and health and safety regulations.
Electrical Connection
Connection to the electrical supply should be in accordance with valid
regulations and safety standards. The connection cable must be protected from
the risk of thermal damage. We recommend connecting the dishwasher to the
power supply via a suitable plug and socket as this will make it easier to
carry out the electrical safety test during commissioning and after any
service work. For hard-wired dishwashers, connection should be made via a
suitable mains switch with all-pole isolation, which in the off position
ensures a 3 mm gap between all open contacts.
Water Connection
- Cold Water: Ensure a water connection of 0 – 60 mm.
Dosage
- Internal Dosage Pump (DOS): Power Consumption: 0.35 kWh
- External Dosage Pump: Power Consumption: 0.40 kWh
FAQ
Can I install the dishwasher myself?
No, the dishwasher must be installed by an authorized technician.
What should I do if I encounter any issues during installation?
Please refer to the service documentation and contact customer support for
assistance.
Installation notes
For safe installation and commissioning of the dishwasher please read the
installation plan, the service documentation and the operating instructions.
This installation plan includes the dimensions of the appliance, the technical
data, and the requirements to be met on site for the installation of the
dishwasher.
Installation requirements
This dishwasher must be installed by an authorized technician in accordance
with the installation instructions supplied. This dishwasher must be installed
under all applicable standards and guidelines, including legal requirements
and health and safety regulations.
Electrical connection
Connection to the electrical supply should be in accordance with valid
regulations and safety standards. The connection cable must be protected from
the risk of thermal damage. We recommend connecting the dishwasher to the
power supply via a suitable plug and socket as this will make it easier to
carry out the electrical safety test during commissioning and after any
service work. For hard-wired dishwashers, the connection should be made via a
suitable mains switch with all-pole isolation, which in the off position
ensures a 3 mm gap between all open contacts. Both the main switch and the
socket must be easily accessible after installation.
Faulty components must only be replaced by genuine Miele original spare parts. Only when these parts are fitted can the safety standards of the machine be guaranteed. If the connection cable is faulty it must only be replaced by a Miele-approved service technician to protect the user from danger.
Equipotential bonding and earthing
For added safety, the dishwasher should be protected with a residual
current device with a trip current of 30 mA. Equipotential bonding should be
carried out if required. The screw connection point for equipotential bonding
is located at the back of the dishwasher.
Water connection (without steam condenser)
The dishwasher can be plumbed in to the cold water, hot water and drainage
points without a backflow protection device. The stopcock to the water supply
must be easily accessible. The water supply to the dishwasher can be connected
to either cold water or hot water.
Water connection (with steam con-denser)
The machine can be plumbed in to the cold water, hot water, demin-eralised
water and drainage points without a backflow protection device. Use the
enclosed Y-piece to establish the water intake for the dishwasher (cold water)
and the steam condenser. Alternatively, you can install an additional cold
water line to connect the steam condenser. If hot water is not available, both
intake hoses (cold and hot water) must be connected to the cold water supply
via a Y-piece. The stopcock to the water supply must be easily accessible.
Environmental requirements
Condensate can build up in the area surrounding the dishwasher. Any
furniture and fittings in the room must therefore be suitable for purpose. If
the machine is fitted under a suitable worktop, the panel supplied must be
fitted above the door aperture to protect the work-top from moisture damage.
Connecting an external dispensing system
Up to two dispensing systems for liquid cleaning agents and rinsing agents
can be connected to the back of the dishwasher. Machines with integrated
dispensing systems have an external connection for rinsing agents.
Liquid agents:
Position of external containers
The liquid agent container for external dispensing must be positioned either
next to or underneath the machine only. The container may be placed on the
floor or in an adjacent cabinet. Do not place the con-tainer on top of or
above the machine. Make sure that the dispensing hose does not get kinked or
trapped.
Appliance dimensions
Freestanding appliance
- PG 8055
- PG 8056 (DOS)
- PG 8057 TD (DOS)
- PD 8058 (DOS)
- PG 8059 (DOS)
- PG 8096 (DOS)
- PG 8099 (DOS)
Built-under appliance
front plinth area, varies depending on appliance type
- PG 8055 U, PG 8056 U, PG 8056-1, PG 8061 U
- PG 8056 U DOS, PG 8096 U (DOS), PG 8099 U (DOS)
front plinth area, varies depending on appliance type
- PG 8057 TD U, PG 8058 U, PG 8059 U
- PG 8057 TD U DOS, PG 8058 U DOS, PG 8059 U DOS
Connections on the back of the appliance
- PG 8055, KW only
- PG 8056 (DOS)
- PG 8061, PG 8056-1,
- PG 8096 (DOS)
- PG 8099 (DOS)
- PG 8057 TD (DOS)
- PG 8058 (DOS)
- PG 8059 (DOS)* only PG 8058 (DOS)
On-site connections
| KW | Cold water | WW | Hot water |
|---|---|---|---|
| AW | Wastewater | EL | Electrical connection |
| DS | External dispensing, power supply connection | PA | Equipotential bonding |
| VE | DI water | DK | Cold water for steam condeser |
Technical data
Electrical connection EU, CH, CN, RU, UA, KZ
Voltage| | 3N AC 400 V /
50 Hz
| AC 230 V / 50 Hz
---|---|---|---
Power rating| | 8.9 kW| 3.4 kW
Fuse rating| | 3 x 16 A| 1 x 16 A
Mains connection cable, min. cross-section| | 5 x 2.5 mm²| 3 x 1.5 mm²
Length of connection cable (H05(07)RN-F)| | 1.7 m| 1.7 m
Electrical connection BE, NO
| Voltage | 3 AC 230 V / 50 Hz | AC 230 V / 50 Hz | |
|---|---|---|---|
| Power rating | 7.1 kW | 2.9 kW | |
| Fuse rating | 3 x 20 A | 3 x 16 A | |
| Mains connection cable, min. cross-section | 3 x 1.5 mm² | 3 x 1.5 mm² | |
| Length of connection cable (H05(07)RN-F) | 1.7 m | 1.7 m |
Electrical connection AU
Voltage| 3N AC 400 V /
50 Hz
| AC 230 V / 50 Hz| AC 230 V / 50 Hz
---|---|---|---
Power rating| 8.9 kW| 5.9 kW| 2.9 kW
Fuse rating| 3 x 15–16 A| 1 x 30–32 A| 1 x 15–16 A
Mains connection cable, min. cross-section| 5 x 2.5 mm²| 3 x 4 mm²| 3 x 1.5
mm²
Connection cable length| 1.8 m| 1.9 m| 1.8 m
Electrical connection US, CA
Voltage| 2 AC 208 V 60 Hz| 3 AC 208 V 60 Hz| 3 AC 240 V 60 Hz| 2 AC 240 V 60
Hz
---|---|---|---|---
Power rating| 5.8 kW| 5.8 kW| 5.8 kW| 5.8 kW
Fuse rating| 2 pole x 30 A| 3 pole x 20 A| 3 pole x 20 A| 2 pole x 30 A
Mains connection cable, min. cross-section| 3 x AWG 10
(3 x 5.2 mm²)
| 4 x AWG 12
(4 x 3.3 mm²)
| 4 x AWG 12
(4 x 3.3 mm²)
| 3 x AWG 10
(3 x 5.2 mm²)
Connection cable length| approx. 5’9”
(1.8 m)
| approx. 5’9”
(1.8 m)
| approx. 5’9”
(1.8 m)
| approx. 5’9”
(1.8 m)
Electrical connection| NEMA L6-30| NEMA L15-20| NEMA L15-20| NEMA L6-30
Cold water
| Max. temperature | 20 °C | 68 °F |
|---|---|---|
| Max. permitted water hardness | 10714 mmol/l / 60 °dH | 63 gpg |
| Recommended flow pressure | 200 kPa | 29 psi |
| Minimum flow pressure with extended water intake | 100 kPa | 14.5 psi |
| Maximum flow pressure | 1000 kPa | 145 psi |
| Flow rate | 7.5 l/min | 2 gal/min |
| On-site threaded union in accordance with DIN 44991 (flat sealing) | 3/4 inch |
3/4 Male Garden Hose Thread
Inlet hose length| 1.7 m| 5′ 7″
Length of steam condenser inlet hose| 1.7 m| 5′ 7″
Hot water
| Max. temperature | 65 °C | 149 °F |
|---|---|---|
| Max. permitted water hardness | 10714 mmol/l / 60 °dH | 63 gpg |
| Recommended flow pressure | 200 kPa | 29 psi |
| Minimum flow pressure with extended water intake | 40 kPa | 5.8 psi |
| Maximum flow pressure | 1000 kPa | 145 psi |
| Flow rate | 7.5 l/min | 2 gal/min |
| On-site threaded union in accordance with DIN 44991 (flat sealing) | 3/4 inch |
3/4 Male Garden Hose Thread
Inlet hose length| 1.7 m| 5′ 7″
Length of steam condenser inlet hose| 1.7 m| 5′ 7″
Wastewater
| Max. waste water temperature | 85 °C | 185 °F |
|---|---|---|
| Max. waste water temperature PG 8057 TD | 93 °C | 200 °F |
| Drain hose length, standard | 1.5 m | 4′ 9″ |
| Drain hose, max. drainage length | 4.0 m | 13′ 1″ |
| Max. drain pump delivery head from bottom edge of machine | 1.0 m | 3′ 3″ |
| Max. transient flow rate | 16 l/min | 4.2 gal/min |
| On-site sleeve for drain hose (Ø x length) | 22 x 30 mm | 7/8″ x 1 3/16″ |
| Drain hose (Ø) | 22 mm | 7/8″ |
Machine data
| Machine feet height adjustment | 0 – 60 mm | 0 – 2 3/8″ |
|---|---|---|
| Max. net weight | 62.5 kg | 138 lbs |
| Max. floor load during operation | 1200 N | 1200 N |
| Min. access width, incl. transport pallet | 670 mm | 26 3/8″ |
| Min. access depth, incl. transport pallet | 740 mm | 29 3/8″ |
| Min. access height, incl. transport pallet | 920 mm | 36 1/4″ |
Sound pressure LpA, washing and drying
PG 8055, PG 8056, PG 8056-1, PG 8096, PG 8099
| 47 dB| 47 dB
Sound pressure LpA, washing and drying PG 8057 TD, PG 8058, PG 8059| 45 dB| 45
dB
Dispensing Internal dispenser pump (DOS)
| Max. delivery head | 1.5 m | 4.9″ |
|---|---|---|
| Length of dispenser hose, back of appliance to suction lance | ca. 1.8 m | ca. |
5.9″
External dispenser pump
| Max. delivery head | 1.5 | 4.9″ |
|---|---|---|
| Length of dispenser hose, DOS module to suction lance | ca. 1.8 | ca. 5.9″ |
| Length of dispenser hose, back of appliance to DOS module | ca. 2.8 | ca. 9.2″ |
| Length of power cable, back of appliance to DOS module | ca. 2.8 | ca. 9.2 |
Heat dissipation rate to installation site
| From heat radiation during operation | 0.35 kWh | 1194 BTU |
|---|---|---|
| From load items whilst unloading | 0.40 kWh | 1365 BTU |
Installation requirements
| Permitted ambient temperature | 5 – 40 °C | 40 – 104 °F |
|---|---|---|
| Max. relative humidity up to 31 °C | 80 % | 80 % |
| Rel. humidity, declining proportionally to 40 °C | 50 % | 50 % |
| Max. altitude above sea level up to | 2000 m | 2000 m |
Manufacturer: Miele & Cie. KG Carl-Miele-Straße 29 33332 Gütersloh Germany
Manufacturing site : Miele & Cie. KG Mielestraße 2 33611 Bielefeld Germany
Internet : www.miele.com/professional
M.-Nr. 11 768 930 / 03
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>