91519 Advanced VX Mount

Specifications

• Models: #91519- Advanced VX Mount, #32054- Advanced VX 6
  Newtonian Telescope, #32062- Advanced VX 8 Newtonian Telescope,

  22020- Advanced VX 6 Refractor Telescope, #12025- Advanced VX 5

  Schmidt-Cassegrain Telescope, #12079- Advanced VX 6
  Schmidt-Cassegrain Telescope, #12026- Advanced VX 8
  Schmidt-Cassegrain Telescope, #12046- Advanced VX 9.25
  Schmidt-Cassegrain Telescope, #12067- Advanced VX 11
  Schmidt-Cassegrain Telescope, #12031- Advanced VX 8 EdgeHD
  Telescope, #12033- Advanced VX 9.25 HD Telescope

Introduction

Congratulations on your purchase of the Celestron Advanced VX
telescope mount. The Advanced VX German equatorial mount has been
designed with the highest quality materials to ensure stability and
durability. Your telescope is designed to give you years of fun and
rewarding observations. However, there are a few things to consider
before using your telescope that will ensure your safety and
protect your equipment. Furthermore, the Advanced VX mount is
versatile — it will grow with you as your interest grows from
astronomical observing to astroimaging.

Features

• High-quality materials for stability and durability
• Versatile and suitable for both astronomical observing and
  astroimaging

Advanced VX Mount

Assembly

This section covers the assembly instructions for your Celestron
Advanced VX mount. Your mount should come with all of the
following:

• Optical Tube
• Control Panel
• Advanced VX Equatorial Mount
• Latitude Adjustment Scale
• Tripod Center Leg Brace/Accessory Tray
• Tripod
• Dec Motor Housing
• Counterweight
• RA Motor Housing
• Counterweight Bar
• Hand Control

If you purchased the Advanced VX mount by itself, you should
receive one counterweight in the box. If you purchased an Advanced
VX telescope kit, you may receive one or two additional
counterweights, depending on the optical tube included in the kit.
These counterweights will be packed in separate boxes. More
information can be found in the section of the manual concerning
the use of your optical tube.

Remove all the pieces from their respective inner boxes and
place on a flat, clear work area. A large floor space is ideal.
When setting up your Celestron mount, you must start with the
tripod and work up from there. These instructions are laid out in
the order each task must be performed.

Computerized Hand Control

The computerized hand control allows you to easily navigate the
Advanced VX mount and access various features. It provides a
user-friendly interface for controlling the telescope.

Object Catalog

The object catalog contains a list of celestial objects that you
can select and track using the Advanced VX mount. It includes
various categories such as planets, stars, galaxies, and more.

Slewing to an Object

To slew to an object, follow these steps:

1. Turn on the mount and the computerized hand control.
2. Select the desired object from the object catalog.
3. The mount will automatically move to the specified object’s
   coordinates.

Advanced VX Main Menu Tree

The main menu tree on the computerized hand control allows you
to access different settings and options. It provides a
hierarchical structure for navigating through the various features
of the Advanced VX mount.

Optical Tube Assemblies

The Advanced VX mount is compatible with various optical tube
assemblies (OTAs) for different types of telescopes. The following
sections provide instructions for setting up specific types of
OTAs.

Setting up the Refractor

To set up a refractor telescope on the Advanced VX mount, follow
these steps:

1. Attach the refractor OTA to the mount using the appropriate
   mounting hardware.

2. Securely tighten all connections.

3. Ensure that the OTA is properly balanced.

Setting up the Newtonian Reflector

To set up a Newtonian reflector telescope on the Advanced VX
mount, follow these steps:

1. Attach the Newtonian OTA to the mount using the appropriate
   mounting hardware.

2. Securely tighten all connections.

3. Ensure that the OTA is properly balanced.

Setting up the EdgeHD & Schmidt-Cassegrain Optical

Tubes

To set up EdgeHD or Schmidt-Cassegrain optical tubes on the
Advanced VX mount, follow these steps:

1. Attach the optical tube to the mount using the appropriate
   mounting hardware.

2. Securely tighten all connections.

3. Ensure that the OTA is properly balanced.

Aligning the Finderscope

The finderscope is used to locate objects in the sky before
slewing the telescope. Proper alignment is essential for accurate
pointing. To align the finderscope, follow these steps:

1. Choose a bright star in the sky.

2. Center the star in the main telescope using the computerized
   hand control.

3. Adjust the finderscope’s alignment screws until the star is
   centered in the finderscope’s crosshairs.

Polar Aligning the Mount

Polar alignment is crucial for accurate tracking and imaging. To
polar align the mount, follow these steps:

1. Level the mount and tripod.

2. Set the mount’s latitude using the latitude adjustment
   scale.

3. Aim the mount’s polar axis towards the celestial pole.

4. Use a polar alignment tool or software to fine-tune the
   alignment.

Appendix A – Advanced VX Mount Technical Specifications

The appendix provides detailed technical specifications for the
Advanced VX mount, including dimensions, weight capacity, motor
type, and more.

Celestron Two Year Limited Warranty

The Celestron Advanced VX mount comes with a two-year limited
warranty. Refer to the warranty documentation for more information
on coverage and terms.

FAQ

Q: Can I use different optical tube assemblies with the

Advanced VX mount?

A: Yes, the Advanced VX mount is compatible with various optical
tube assemblies for different types of telescopes.

Q: How do I align the finderscope?

A: To align the finderscope, choose a bright star in the sky,
center it in the main telescope, and adjust the finderscope’s
alignment screws until the star is centered in the finderscope’s
crosshairs.

Q: What is polar alignment and why is it important?

A: Polar alignment refers to aligning the mount’s polar axis
towards the celestial pole. It is important for accurate tracking
and imaging.

SERIES

INSTRUCTION MANUAL FOR MODELS:

91519- Advanced VX Mount #32054- Advanced VX 6″ Newtonian Telescope #32062-

Advanced VX 8″ Newtonian Telescope #22020- Advanced VX 6″ Refractor Telescope

12025- Advanced VX 5″ Schmidt-Cassegrain Telescope #12079- Advanced VX 6″

Schmidt-Cassegrain Telescope

12026- Advanced VX 8″ Schmidt-Cassegrain Telescope #12046- Advanced VX 9.25″

Schmidt-Cassegrain Telescope #12067- Advanced VX 11″ Schmidt-Cassegrain Telescope #12031- Advanced VX 8″ EdgeHD Telescope #12033- Advanced VX 9.25″ HD Telescope

TABLE OF CONTENTS

Introduction

3

Advanced VX Mount

4

Assembly

5

Computerized Hand Control

10

Object Catalog

14

Slewing to an Object

14

Advanced VX Main Menu Tree

21

Optical Tube Assemblies

23

Setting up the Refractor

24

Setting up the Newtonian Reflector

24

Setting up the EdgeHD & Schmidt-Cassegrain Optical Tubes

25

Aligning the Finderscope

27

Polar Aligning the Mount

27

Appendix A – Advanced VX Mount Technical Specifications

30

Celestron Two Year Limited Warranty

31

2 I ENGLISH

Introduction
Congratulations on your purchase of the Celestron Advanced VX telescope mount The Advanced VX German equatorial mount has been designed with the highest quality materials to ensure stability and durability All this adds up to a telescope that gives you a lifetime of enjoyment with a minimal amount of maintenance

Your telescope is designed to give you years of fun and rewarding observations However, there are a few things to consider before using your telescope that will ensure your safety and protect your equipment

Furthermore, the Advanced VX mount is versatile — it will grow with you as your interest grows from astronomical observing to astroimaging
If you are new to astronomy, you may wish to start off by using the built-in Sky Tour feature, which commands the telescope to find the most interesting objects in the sky and automatically slews to each one If you are an experienced amateur, you will appreciate the comprehensive database of over 40,000 objects, including customized lists of all the best deep-sky objects, bright double stars and variable stars No matter your level of experience, Advanced VX will help you and your friends explore the wonders of the universe
Some of the features of the Advanced VX include:
· High-torque motors for helping to smoothly drive heavier loads
· Permanently Programmable Periodic Error Correction (PEC) to improve your tracking performance
· A dedicated autoguider port for making corrections when astroimaging
· Large, easy to access polar alignment knobs for quick and sure movements
· Ergonomic design that disassembles into compact and portable pieces
· Database filter limits for creating custom object lists
· Storage for programmable user defined objects
· Many other high performance features!

Warning
· Never look directly at the Sun with the naked eye or with a telescope (unless you have the proper solar filter) Permanent and irreversible eye damage may result
· Never use your telescope to project an image of the Sun onto any surface Internal heat build-up can damage the telescope and any accessories attached to it
· Never use an eyepiece solar filter or a Herschel wedge Internal heat build- up inside the telescope can cause these devices to crack or break, allowing unfiltered sunlight to pass through to the eye
· Never leave the telescope unsupervised Make sure an adult who is familiar with the correct operating procedures is with your telescope at all times, especially when children are present

The Advanced VX mount is one of the most sophisticated and easy to use telescopes available on the market today

Take time to read through this manual before embarking on your journey through the universe It may take a few observing sessions to become familiar with your telescope, so you should keep this manual handy until you have fully mastered your telescope’s operation The hand control has built-in instructions to guide you through all the alignment procedures needed to have the telescope up and running in minutes Use this manual in conjunction with the on-screen instructions provided by the hand control The manual gives detailed information regarding each step as well as needed reference material and helpful hints guaranteed to make your observing experience as simple and pleasurable as possible

ENGLISH I 3

Advanced VX Mount (Advanced VX with 5″ Schmidt-Cassegrain Optical Tube Shown)
1

7

B

D

2 3
4

8 9
10

C E

5

F

11

A

6

1 Optical Tube 2 Control Panel 3 Advanced VX Equatorial Mount 4 Latitude Adjustment Scale 5 Tripod Center Leg Brace/Accessory Tray 6 Tripod 7 Dec Motor Housing 8 Counterweight 9 R A Motor Housing 10 Counterweight Bar 11 Hand Control

CONTROL PANEL A Power Port B DEC Motor Port C Power Switch D Auxiliary Ports E Hand Control Port F Auto Guider Port

4 I ENGLISH

Assembly
This section covers the assembly instructions for your Celestron Advanced VX mount Your mount should come with all of the following:
· Equatorial head
· Tripod
· Accessory tray
· Counterweight bar with locking nut
· Azimuth adjustment screws (x2)
· Hand control
· Hand control holder (2 pieces)
· Declination motor cable
· Car battery adapter cable
· Counterweight
If you purchased the Advanced VX mount by itself, you should receive one counterweight in the box If you purchased an Advanced VX telescope kit, you may receive one or two additional counterweights, depending on the optical tube included in the kit These counterweights will be packed in separate boxes More information can be found in the section of the manual concerning the use of your optical tube
Remove all the pieces from their respective inner boxes and place on a flat, clear work area A large floor space is ideal When setting up your Celestron mount, you must start with the tripod and work up from there These instructions are laid out in the order each task must be performed
Setting up the Tripod
The Advanced VX tripod comes with an all-metal center leg brace/accessory tray to give rock solid support to the mount
The tripod comes fully assembled with a metal plate, called the tripod head that holds the legs together at the top In addition, there is a central rod that extends down from the tripod head that attaches the equatorial mount to the tripod To set up the tripod:
1 Stand the tripod upright and pull the tripod legs apart until each leg is fully extended The tripod will now stand by itself
2 To adjust the height of the legs, loosen the lever found at the bottom of each leg by rotating it counterclockwise
3 Slide each leg out to the desired length and secure in place by rotating the levers clockwise Make sure the levers are tight so the legs do not accidentally slide inward when you add weight to the tripod

Before securing the mount to the tripod:
1 Locate the Azimuth Adjustment Knobs from the box containing the Advanced VX equatorial head
2 Thread one knob into each of the holes located on either side of the mount
3 Only thread the knobs about half way in, leaving enough space for the tripod alignment peg, which will need to fit between the two screw tips
Attaching the Equatorial Mount
The Advanced VX equatorial mount allows you to tilt the telescope’s axis of rotation so that you can track the stars as they move across the sky On one side of the tripod head is a metal alignment peg for aligning the mount This side of the tripod will face north when setting up for an astronomical observing session To attach the equatorial head:
1 Locate the azimuth adjustment screws on the equatorial mount
2 Retract the azimuth adjustment screws so they no longer extend into the azimuth housing on the mount Do NOT remove the screws since they are needed later for polar alignment.
3 Hold the equatorial mount over the tripod head so the azimuth housing is above the metal peg
4 Place the equatorial mount on the tripod head so that the two are flush
5 Push the knob located on the central rod on the underside of the tripod head upward and turn it clockwise to hold the equatorial mount firmly in place

Tripod Head

Equatorial Mount
Azimuth Knobs (on both sides of mount)

Attaching the Azimuth Adjustment Knobs
To ensure safe shipment of your Advanced VX mount, the azimuth adjustment knobs have been removed from the mount and will need to be attached

Mounting Knob

ENGLISH I 5

Your Advanced VX tripod comes with the alignment peg installed so the polar axis and counterweight bar extends between two tripod legs If you wish, you can reposition the alignment peg so the counterweight bar extends directly over a tripod leg This is a matter of personal preference and does not affect the stability of the mount Observers at lower latitudes will prefer to leave the alignment peg between two legs to avoid the counterweight from making contact with the tripod leg when the counterweight is in the lowest part of its swing To change the position of the alignment peg:

Mounting Knob

Alignment Peg

Tray Knob

Central Column
Accessory Tray

Tripod Head

Lock Nut

Installing the Counterweight Bar
To properly balance the telescope, the mount comes with a counterweight bar and at least one counterweight (depending on model) To install the counterweight bar:

1 Locate the counterweight bar and locking nut from the box containing the equatorial head The locking nut should already be threaded onto the end of the counterweight bar

1 Use a wrench to hold the alignment peg in place while using another wrench to loosen the locking nut underneath the alignment peg
2 Once the nut is loose, you can unthread the alignment peg and move it to the threaded hole on the opposite side of the tripod head
3 Thread the peg in until it stops, and back it off until the flat sides of the alignment peg are square to the tripod
4 Hold the peg in this position with one wrench while using another wrench to tighten the locking nut against the tripod head
5 Mount the equatorial head as described above

2 Locate the opening in the equatorial mount on the declination axis and thread the counterweight bar into the opening until it is tight
3 Tighten the counterweight bar lock nut fully
Declination Axis Lock Nut
Counterweight Bar

Attaching the Accessory Tray
The Advanced VX mount comes with an accessory tray that has holes specially designed for 1 25″ and 2″ eyepieces The accessory tray also acts as a tripod leg tensioner to add stability to the mount To install the tray:
1 Remove the nut and washer from the lower side of the tripod’s central rod
2 Slide the accessory tray over the central rod so that each arm of the tray is pushing against the inside of the tripod legs
3 Thread the accessory tray knob onto the central rod and tighten

Counterweight
Safety Screw Counterweight Lock Screw
Once the bar is securely in place, you are ready to attach the counterweight
Observing Tip: Since the fully assembled telescope can be quite heavy, position the mount so that the polar axis is pointing towards north before the optical tube assembly and counterweights are attached This will make the polar alignment procedure much easier
Installing the Counterweight To install the counterweight(s) that were included with your mount or telescope kit:
1 Orient the mount so the counterweight bar points toward the ground

6 I ENGLISH

2 Remove the counterweight safety screw on the bottom end of the counterweight bar by turning it counterclockwise This screw prevents the counterweight from falling off the mount in the case the counterweight locking screw comes loose
3 Loosen the locking screw on the side of the counterweight
4 Slide the counterweight over the counterweight bar and move it about halfway up the bar
5 Tighten the locking screw on the side of the counterweight to hold it in place
6 Replace the counterweight safety screw
Tip: The hole in the center of your counterweight is slightly larger on one side When you slide the counterweight onto the counterweight bar, make sure that the smaller hole is facing the equatorial head This allows you to slide the counterweight over the safety screw at the bottom of the counterweight bar in case you need a little bit more adjustment to balance additional accessories mounted on your optical tube The smaller hole prevents the counterweight from completely sliding over the safety screw
Attaching the Hand Control Holder
The Advanced VX telescope models come with a hand control holder that attaches to a tripod leg The hand control holder comes in two pieces: the leg clamp that snaps around the tripod leg and the holder which attaches to the leg clamp To attach the hand control holder:
1 Place the leg clamp up against one of the tripod legs and press firmly until the clamp wraps around the leg
2 Slide the back of the hand control holder downward into the channel on the front of the legs clamp until it snaps into place
Hand Control Holder

that the mount does not move suddenly while attaching the telescope To mount the telescope tube:
1 Loosen the two mounting screws on the side of the telescope mounting platform This allows you to slide the dovetail bar onto the mount
2 If your telescope is equipped with one, remove the safety screws located beneath the dovetail bar
3 Slide the dovetail bar on the telescope tube into the mounting platform of the mount Slide the telescope so that the back of the dovetail bar is close to the back of the mounting platform
4 Tighten the mounting screws on the side of the mounting platform to hold the telescope in place
Now that the optical tube is securely in place, the visual accessories can be attached to the telescope This is covered in detail in the section of this manual dealing with the use of optical tubes
Safety Screw
Dovetail Bar
Telescope Mounting Screw
Using the Dual Saddle Plate Your Advanced VX mount comes with a dual saddle plate, allowing you to use any optical tube using a 1 75″ V-plate dovetail bar (Synta, Vixen) or the wider 3″ (75mm) D-plate style dovetail bar (CGEM, CGX, CGX-L)
Your Advanced VX mount should already be set up to use the smaller V-plate To convert the mount for use with the larger D-plate, simply remove the two bolts from the left side of the dovetail saddle using a 6mm Allen-key

Leg Clamp

Attaching an Optical Tube to the Mount
The telescope attaches to the mount via a dovetail slide bar, which is mounted along the bottom of the telescope tube Before you attach the optical tube, make sure that the declination and right ascension clutch knobs are tight and the counterweight(s) are securely installed This will ensure

Remove the two hand knobs and transfer them over to the threaded holes you just uncovered

ENGLISH I 7

telescope (i e , the telescope remains stationary when the R A clutch knobs are loose)
6 Tighten the screw on the counterweight to hold it in place

To keep the empty threads clean, always replace the Allen-key screws into the set of holes you are not using

Moving the Telescope Manually In order to properly balance your telescope, you will need to move your telescope manually at various portions of the sky to observe different objects To make rough adjustments, loosen the R A and DEC clutch knobs slightly and move the telescope in the desired direction
Both the R A and DEC axis have lock levers to clutch down each axis of the telescope To loosen the clutches on the telescope, rotate the lock levers counterclockwise
Declination Clutch Lever

Tip: While the above instructions describe a perfect balance arrangement, there should be a SLIGHT imbalance to ensure the best possible tracking When the scope is on the west side of the mount the counterweight should be slightly imbalanced to the counterweight bar side And when the tube is on the east side of the mount, there should be a slight imbalance toward the telescope side This is done so that the worm gear is pushing against a slight load The amount of the imbalance is very slight When taking astroimages, this balance process can be done for the specific area at which the telescope is pointing to further optimize tracking accuracy

RA Clutch Lever
Balancing the Mount in R.A. To eliminate undue stress on the mount, the telescope should be properly balanced around the polar axis Proper balancing is crucial for accurate tracking To balance the mount:
1 Verify that the telescope is securely attached to the telescope mounting platform
2 Loosen the R A lock lever and position the telescope off to one side of the mount The counterweight bar will extend horizontally on the opposite side of the mount
3 Release the telescope — GRADUALLY — to see which way the telescope “rolls”
4 Loosen the set screws on the side of the counterweight, so it can be moved the length of the counterweight bar
5 Move the counterweight to a point where it balances the

Balancing the Mount in DEC
Although the mount does not track in declination, the telescope should also be balanced in this axis to prevent any sudden motions when the DEC lock lever is loose To balance the telescope in DEC:
1 Loosen the R A clutch lock lever and rotate the telescope so that it is on one side of the mount (i e , as described in the previous section on “Balancing the Mount in R A”)
2 Tighten the R A lock lever to hold the telescope in place
3 Loosen the DEC clutch lock lever and rotate the telescope until the tube is parallel to the ground
4 Release the tube — GRADUALLY — to see which way it rotates around the declination axis DO NOT LET GO OF THE TELESCOPE TUBE COMPLETELY!
5 Slightly loosen the knobs that hold the telescope to the mounting platform and slide the telescope either forward or backward until it remains stationary when the DEC clutch is loose Do NOT let go of the telescope tube while the knob on the mounting platform is loose It may be necessary to rotate the telescope so that the counterweight bar is pointing down before loosening the mounting platform screw
6 Tighten the knobs on the telescope mounting platform to hold the telescope in place

8 I ENGLISH

Like R A balance, these are general balance instructions and will reduce undue stress on the mount When taking astroimages, this balance process should be done for the specific area at which the telescope is pointing
Adjusting the Mount
In order for a motor drive to track accurately, the telescope’s axis of rotation must be parallel to the Earth’s axis of rotation, a process known as polar alignment Polar alignment is achieved NOT by moving the telescope in R A or DEC but by adjusting the mount vertically, which is called altitude and horizontally, which is called azimuth This section simply covers the correct movement of the telescope during the polar alignment process The actual process of polar alignment, or making the telescope’s axis of rotation parallel to the Earth’s, is described later in this manual in the section on “Polar Alignment ”
Adjusting the Mount in Altitude
· To increase the latitude of the polar axis, tighten the rear latitude adjustment screw and loosen the front screw
· To decrease the latitude of the polar axis, tighten the front latitude adjustment screw (located below the counterweight bar and loosen the rear screw
The latitude adjustment on the Advanced VX mount has a range from approximately 7° to 77°

Azimuth Adjustment Knobs

Latitude Adjustment Knobs

· Turning the right adjustment knob clockwise moves the mount toward the right
· Turning the left adjustment knob clockwise moves the mount to the left
Both screws push off of the alignment peg on the tripod head, which means you may have to loosen one screw while tightening the other The screw that holds the equatorial mount to the tripod may have to be loosened slightly
Keep in mind that adjusting the mount is done during the polar alignment process only Once polar aligned, the mount must NOT be moved Pointing the telescope is done by moving the mount in right ascension and declination, as described earlier in this manual
Attaching the Declination Cable
The Advanced VX mount comes with a cable that connects the electronic control panel to the declination motor To attach the motor cables:
· Locate the Declination cable and plug one end of the cable into the port on the electronics panel labeled DEC Port
· Plug the other end of the cable into the port located on the declination motor
Powering the Telescope
The Advanced VX mount can be powered by the supplied car battery adapter or optional 12V AC adapter Use only adapters supplied by Celestron Using any other adapter may damage the electronics and will void your manufacturer’s warranty
1 To power the telescope with the car battery adapter (or 12V AC adapter), simply plug the round post into the 12V outlet on the electronic panel and plug the other end into your car’s cigarette lighter outlet or portable power supply
2 Turn on the power to the telescope by flipping the switch, located on the electronics panel, to the “On” position

It is best to always make final adjustments in altitude by moving the mount against gravity (i e , using the rear latitude adjustment screw to raise the mount) To do this, you should loosen both latitude adjustment screws and manually push the front of the mount down as far as it will go Tighten the rear adjustment screw to raise the mount to the desired latitude

Adjusting the Mount in Azimuth
For rough adjustments in azimuth, simply pick up the telescope and tripod and move it For fine adjustments in azimuth:
Turn the azimuth adjustment knobs located on either side of the azimuth housing While standing behind the telescope, the knobs are on the front of the mount

ENGLISH I 9

Computerized Hand Control
You have received a newly upgraded NexStar+ hand control with your telescope The hand control now features a USB connector used for linking to a PC with control software, and to perform firmware updates This is a drop-in replacement for all existing telescopes that accept the NexStar+ Hand Control with RS-232 Connector
Update hand control firmware over USB without external power or without connecting to the mount To update the firmware, simply plug a mini USB cable (not included) from your PC to the port on the bottom of the hand control, and run Celestron Firmware Manager (CFM), available for free from the support section on Celestron com

1

1

8

22

89 9

3

4

4

5

11

10

6

11

15

12

7

13

14
10 I ENGLISH

1 Liquid Crystal Display (LCD) Window: Has a four-line, 18 character display screen that has red backlighting for comfortable viewing of telescope information and scrolling text
2 Align: Instructs the hand control to begin the process of aligning your telescope
3 Direction Keys: Allows complete control of the Advanced VX mount in any direction Use the direction keys to center objects in the eyepiece or manually slew telescope
4 Catalog Keys: The Advanced VX has a key on the hand control to allow direct access to each of the main catalogs in its 40,000+ object database Your mount contains the following catalogs in its database:
· Solar System ­ All 7 planets in our Solar System plus the Moon, Sun and Pluto
· Stars ­ Custom lists of all the brightest stars, double stars, variable stars and asterisms
· Deep Sky ­ Custom lists of all the best galaxies, nebulae and clusters as well as the complete Messier and select NGC objects
5 Identify: Searches the Advanced VX databases and displays the name and offset distances to the nearest matching objects
6 Menu: Displays the many setup and utilities functions, such as tracking rate and user defined objects and many others
7 Option (Celestron Logo): Can be used in combination with other keys to access more advanced features and functions
8 Enter: Pressing ENTER allows you to select any of the Advanced VX functions, accept entered parameters and slew the telescope to displayed objects
9 Back: Pressing BACK will take you out of the current menu and display the previous level of the menu path Press BACK repeatedly to get back to a main menu or use to erase data entered by mistake
10 Sky Tour: Activates the tour mode, which seeks out all the best objects in the sky and automatically slews the Advanced VX to those objects
11 Scroll Keys: Used to scroll up and down within any of the menu lists A double arrow symbol on the right side of the LCD indicates that the scroll keys can be used to view additional information
12 Motor Speed: Slews the telescope faster or slower when the direction buttons are pressed
13 Object Info: Displays coordinates and useful information about objects selected from the Advanced VX database
14 Mini usb port (cable not included): Links to PC to control telescope with desktop or to perform firmware updates
15 Help Menu: In future firmware updates, this button will offer troubleshooting tips For your convenience, it currently functions as a shortcut to the Messier Catalog

Hand Control Operation
This section describes the basic hand control procedures needed to operate all Celestron computerized telescopes These procedures are grouped into three categories: Alignment, Setup and Utilities The alignment section reviews the initial telescope alignment as well as finding objects in the sky The setup section discusses changing parameters such as tracking mode and tracking rate Finally, the last section reviews all of the utilities functions such as calibrating your mount, polar alignment and backlash compensation
Alignment Procedures
In order for the telescope to accurately point to objects in the sky, it must first be aligned with known positions (stars) in the sky With this information, the telescope can create a model of the sky, which it uses to locate any object with known coordinates There are many ways to align your telescope with the sky depending on what information the user is able to provide:
· Two Star Align uses the entered time/location information and allows the user to select which two alignment stars the telescope will automatically slew to
· One Star Align uses the same time/location information but only uses one star for alignment
· Solar System Align will display a list of visible daytime objects (planets and the Moon) available to align the telescope
· Quick-Align will ask you to input all the same information as you would for the Two Star Align procedure However, instead of slewing to the alignment stars for centering and alignment, the telescope bypasses this step and simply models the sky based on the information given
· Last Alignment restores your last saved star alignment and switch position Last Alignment also serves as a good safeguard in case the telescope should lose power
Startup Procedure
Before any of the described alignments are performed, the Advanced VX mount needs to be positioned so that the index marks are aligned on both the right ascension and declination axes Once the index position has been set, the hand control will display the last entered date and time information stored in the hand control
1 Press ENTER to begin the alignment process
2 The hand control will prompt the user to set the mount to its index position Move the telescope mount, either manually or with the hand control, so the index marked in both R A and Dec are aligned Press ENTER to continue
· The hand control will then display the last entered local time, time zone and date
· Use the Up/Down keys (10) to view the current parameters

ENGLISH I 11

· Press ENTER to accept the current parameters · Press BACK to enter current date, time and location
information into the hand control
3 The following information will be displayed:

Note: If incorrect information is entered into the hand control, the BACK button acts like a backspace button, allowing the user to re-enter the correct data
Select one of the alignment methods described below

· Location ­ The hand control will display a list of cities to choose from Choose the city from the database that is closest to your current observing site The city you choose will be remembered in the hand control’s memory so that it will be automatically displayed the next time an alignment is done Alternatively, if you know the exact longitude and latitude of your observing site, it can be entered directly into the hand control and remembered for future use as well To choose a location city:
· Use the Up and Down scroll keys to choose between City Database and Custom Site City Database will allow you to select the closest city to your observing site from a list of either international or U S location Custom Site allows you to enter the exact longitude and latitude of your observing site Select City Database and press ENTER
· The hand control will allow you to choose from either U S or international locations For a listing of U S locations by state and then by city, press ENTER while United States is displayed For international locations, use the Up or Down scroll key to select International and press ENTER
· Use the Up and Down Scroll buttons to choose your current state (or country if an International location was selected) from the alphabetical listing and press ENTER
· Use the Up and Down Scroll buttons to choose the closest city to your location from the displayed list and press ENTER
· Time ­ Enter the current local time for your area You can enter either the local time (i e , 08:00), or you can enter military time (i e , 20:00)
· Select PM or AM If military time was entered, the hand control will bypass this step
· Choose between Standard Time or Daylight Saving Time Use the Up and Down scroll buttons (10) to toggle between options
· Select the time zone that you are observing from Again, use the Up and Down buttons (10) to scroll through the choices Refer to Time Zone map in Appendix for more information
· Date ­ Enter the month, day and year of your observing session
Note: Updating Your Location ­ Since you may not need to update your observing location as often as the date and time, it is not displayed each time you update the date and time To update your city, press BACK at any time when updating your date and time Continue to press BACK to change the state, country or to add longitude/latitude coordinates

Two Star Align
Two-Star Align allows the user to select two stars on which to align the telescope To align your telescope using the Two-Star Align method:
1 Select Two-Star Align from the alignment choices given Based on the date and time information entered, the hand control will automatically select and display a bright star that is above the horizon
· Press ENTER to select this star as your first alignment star
· If for some reason the chosen star is not visible (perhaps behind a tree or building), press BACK to have the hand control automatically select the next brightest star
· Or you can use the Up/Down keys to browse the entire Named Star list and select any one of over two hundred alignment stars
2 Once the telescope is finished slewing to your first alignment star, the display will ask you to use the arrow buttons to align the selected star with the cross hairs in the center of the finderscope When centered in the finder, press ENTER
The display will then instruct you to center the star in the field of view of the eyepiece When the star is entered, press ALIGN to accept this star as your first alignment star
Important: When moving the telescope, remember to always finish slewing using the UP and RIGHT direction buttons on the hand control to eliminate any mechanical backlash in the gears.
3 After the first alignment star has been entered, the hand control will automatically select a second alignment star and have you repeat this procedure for that star
When the telescope has been aligned on both stars, the display will ask you if you wish to add additional calibration stars Calibration stars are used to improve the pointing accuracy of your telescope by compensating for subtle opto-mechanical misalignments between the telescope optics and the mount Therefore, it is usually a good idea to add at least one additional calibration star to improve the mount’s all-sky pointing accuracy
4 Press ENTER to select a calibration star Select a star the same way you did with the first two alignment stars and press ENTER You will notice that all the calibration stars displayed are located on the opposite side of the side of the sky (Meridian) as the original alignment stars This is essential for an accurate calibration of the mount
Finally, you can choose to continue to add additional calibration stars or Press BACK to complete the alignment

12 I ENGLISH

Note: East/West Filtering ­ In order to ensure the best possible full-sky pointing accuracy, your computerized mount automatically filters and chooses its initial alignment stars so that the first two alignment stars are located on one side of the Meridian and any calibration stars are on the opposite side of the Meridian, as indicated by the “W” or “E” displayed in the upper-right corner of the LCD East/West filtering can be changed simply by pressing the MENU button at any time during the alignment process

3 Use the UP and Down keys to select Sun Menu and press ENTER
4 Press ENTER again to allow the Sun to appear on the hand control display
The Sun can be removed from the display by using the same procedure as above
Tip: To improve the telescope pointing accuracy, you can use the Re-Align feature as described below

Tips for adding calibration stars:
· Although for casual observing it is not necessary to add calibration stars, it is recommended that you add as many as three calibration stars for optimal point accuracy
· Choosing calibration stars that are near the celestial equator offer better results than stars near the celestial poles
· Although it is not necessary to use calibration stars if the telescope mount has not been moved since its original alignment/calibration, it may be necessary to recalibrate the telescope if the optical tube has been removed for any reason

Quick-Align
Quick-Align uses all the date and time information entered at startup to align the telescope However, instead of slewing to the alignment stars for centering and alignment, the telescope bypasses this step and simply models the sky based on the information given This will allow you to roughly slew to the coordinates of bright objects like the Moon and planets and provides the telescope with information needed to track objects in any part of the sky (depending on accuracy of polar alignment) Quick-Align is not meant to be used to accurately locate small or faint deep-sky objects or to track objects accurately for astroimaging
To use Quick-Align, simply select Quick Align from the alignment options and press ENTER The telescope will automatically use the entered date/time parameters to align itself with the sky and display Alignment Successful

Note: Once a Quick-Align has been done, you can use the Re-alignment feature (see below) to improve your telescope’s pointing accuracy

Note: Meridian ­ The meridian is an imaginary line in the sky that starts at the North celestial pole and ends at the South celestial pole and passes through the zenith If you are facing south, the meridian starts from your Southern horizon and passes directly overhead to the North celestial pole
For safety purposes, the Sun will not be displayed in any of the hand control’s customer object lists unless it is enabled from the Utilities Menu To allow the Sun to be displayed on the hand control, do the following:
1 Press the BACK button until the display reads “Advanced VX Ready”
2 Press the MENU button and use the Up and Down keys to select the Utilities menu Press ENTER

Last Alignment
The Last Alignment method will automatically recall the last stored index positions to continue using the alignment that was saved when the telescope was last powered down This is a useful feature should your telescope accidentally lose power or be powered down
Note: Just like with Quick-Align, you can use the Re-alignment feature (see below) to improve your telescope’s pointing accuracy after using the Last Alignment method To maintain a more accurate alignment over a series of observing sessions, use the Hibernate feature described later in this chapter
Re-Alignment
The mount has a re-alignment feature that allows you to replace any of the original alignment stars with a new star or celestial object This can be useful in several situations:
· If you are observing over a period of a few hours, you may notice that your original two alignment stars have drifted towards the west considerably (Remember that stars are moving at a rate of 15° every hour) Aligning on a new star that is in the eastern part of the sky will improve your pointing accuracy, especially on objects in that part of the sky

ENGLISH I 13

· If you have aligned your telescope using the Quick-Align method, you can use Re-Align to align on actual objects in the sky This will improve the pointing accuracy of your telescope without having to re-enter additional information
· If you have used the computer-assisted polar alignment method and have manually moved the mount, it may be necessary to re-align the mount for improved pointing accuracy
To replace an existing alignment star with a new alignment star:
1 Select the desired star (or object) from the database and slew to it
2 Carefully center the object in the eyepiece
3 Once centered, press the BACK button until you are at the main menu
4 With Advanced VX Ready displayed, press the ALIGN key on the hand control to select Alignment Stars from the list of options
5 The display will then ask you which alignment star you want to replace Use the Up and Down scroll keys to select the alignment star to be replaced It is usually best to replace the star closest to the new object This will space out your alignment stars across the sky
6 Press ALIGN to make the change
Object Catalog
Selecting an Object
Once the telescope is properly aligned, you can choose an object from any of the catalogs in the NexStar+ hand control’s database The hand control has a key designated for each category of objects in its database; Solar System objects, Stars and Deep Sky objects
· Solar System ­ The Solar System catalog will display all the planets (and Moon) in our Solar System that are currently visible in the sky To allow the Sun to be displayed as a selectable object in the database, see the Sun Menu option in Scope Setup Menu
· Stars ­ The Stars catalog displays custom lists of all the brightest stars, double (Binary) stars, variable stars, constellations and selected asterisms
· Deep Sky ­ The Deep Sky catalog displays a list of all the best galaxies, nebulae and clusters, as well as the complete Messier and select NGC objects There is also an alphabetical list of all deep sky objects in order by their common name
Use the scroll keys to scroll through the catalogs to find the object you want to view
When scrolling through a long list of objects, holding down either the UP or DOWN key will allow you to scroll through the catalog rapidly

Slewing to an Object
Once the desired object is displayed on the hand control screen, you have two options:
· Press the OBJECT INFO Key. This will give you useful information about the selected object such as magnitude, constellation and extended information about the most popular objects
· Use the UP/DOWN arrow buttons to scroll through the displayed object info
· Use the BACK button to return to the object database
· Press the ENTER Key. This will automatically slew the telescope to the coordinates of the object displayed on the hand control While the telescope is slewing to the object, the user can still access many of the hand control functions (such as displaying information about the object)
NOTE: The Messier, NGC and SAO catalogs require the user to enter a numeric designation Once you have selected the appropriate catalog button and selected the Messier, NGC or SAO catalog, you will see a flashing cursor indicating you are in numeric entry mode Enter the catalog number for the object you want to view Press ENTER to command the telescope to slew to the object or hold the OPTION button (the Celestron logo) and press OBJECT INFO to see information about the object you selected
Caution: Never slew the telescope when someone is looking into the eyepiece. The telescope can move at fast slew speeds and may hit an observer in the eye.
SkyTour Button
The Advanced VX mount includes a tour feature that allows you to choose from a list of interesting objects based on the date and time in which you are observing The automatic tour will display only those objects that are within your set catalog filters limits To activate the Tour feature, press the SKY TOUR key on the hand control
1 Press the SKY TOUR button on the hand control
2 Use the SCROLL buttons to select Best of Tonight
3 The Advanced VX mount will automatically slew in azimuth to its starting position, which will help minimize the chance of wrapping the power cord during the tour
4 The hand control will display the best objects to observe that are currently in the sky
· To see information and data about the displayed object, press the OBJECT INFO key Press it once to display the coordinates of the object Press it again to display the coordinates of the object Press it again to display the text description Press BACK to return to the previous screen

14 I ENGLISH

· To slew to the object displayed, press ENTER · To see the next tour object, press the DOWN key

Identify Button
Pressing the IDENTIFY button will search the mount’s database catalogs and display the name and angular distances to the nearest matching objects from the telescope’s current location This feature can serve two purposes First, it can be used to identify an unknown object in the field of view of your eyepiece Additionally, Identify Mode can be used to find other celestial objects that are close to the objects you are currently observing
For example, if your telescope is pointed at the brightest star in the constellation Lyra, choosing Identify will no doubt return the star Vega as the star you are observing However, the Identify feature will also search its NGC and Solar System databases and display any planets or Deep Sky objects that are close by In this example, the Ring Nebula (M57) would display as being approximately 6° away
The brightness and proximity of the objects displayed can be defined by the user using the Identify Filter under Telescope Setup

Direction Buttons
The hand control has four direction buttons in the center of the hand control which control the telescope motion in altitude (up and down) and azimuth (left and right) The telescope can be controlled at nine different speed rates

1 = 2x 2 = 4x 3 = 8x 4 = 16x 5 = 32x

6 = 3° / sec 7 = 1° / sec 8 = 2° / sec 9 = 4° / sec

Motor Speed Button
Pressing the MOTOR SPEED button (12) allows you to instantly change the speed rate of the motors from high speed slew rate to precise guiding rate or anywhere in between Each rate corresponds to a number on the hand controller key pad The number 9 is the fastest rate (approximately 4° per second, depending on power source) and is used for slewing between objects and locating alignment stars The number 1 on the hand control is the slowest rate (2x sidereal) and can be used for accurate centering of objects in the eyepiece To change the speed rate of the motors:
· Press the MOTOR SPEED key on the hand control The LCD will display the current speed rate
· Press the number on the hand control that corresponds to the desired speed
The hand control has a “double button” feature that allows you to instantly speed up the motors without having to

choose a speed rate To use this feature, simply press the arrow button that corresponds to the direction that you want to move the telescope While holding that button down, press the opposite directional button This will increase the speed to the maximum slew rate
When using the UP and DOWN buttons on the hand control, the slower slew rates (6 and lower) move the motors in the opposite direction than the faster slew rates (7- 9) This is done so that an object will move in the appropriate direction when looking into the eyepiece (i e , pressing the up arrow button will move the star upwards in the field of view of the eyepiece) However, if any of the slower slew rates (rate 6 and below) are used to center an object in the StarPointer, you may need to press the opposite directional button to make the telescope move in the correct direction
Help Button
In future firmware updates, this button will offer troubleshooting tips For your convenience, it currently functions as a shortcut to the Messier Catalog
Menu Button
The Advanced VX mount contains many user-defined setup functions designed to give the user control over the telescopes many features All of the setup and utility features can be accessed by pressing the MENU key and scrolling through the options below
Tracking Menu
Tracking Mode ­ This allows you to change the way the telescope tracks depending on the type of mount being used to support the telescope The telescope has three different tracking modes:
· EQ North ­ Used to track the sky when the telescope is polar aligned in the Northern Hemisphere
· EQ South ­ Used to track the sky when the telescope is polar aligned in the Southern Hemisphere
· Off ­ When using the telescope for terrestrial (land) observation, the tracking can be turned off so that the telescope never moves
Tracking Rate ­ In addition to being able to move the telescope with the hand control buttons, your telescope will continually track a celestial object as it moves across the night sky The tracking rate can be changed depending on what type of object is being observed:
· Sidereal ­ This rate compensates for the rotation of the Earth by moving the telescope at the same rate as the rotation of the Earth, but in the opposite direction When the telescope is polar aligned, this can be accomplished by moving the telescope in right ascension only
· Lunar ­ Used for tracking the Moon when observing the lunar landscape
· Solar ­ Used for tracking the Sun when solar observing with the proper filter

ENGLISH I 15

View Time-Site Menu
This menu displays the current time and longitude/latitude downloaded from the optional SkySync GPS receiver It will also display other relevant time-site information like time zone, Daylight Saving and local sidereal time Local sidereal time (LST) is useful for knowing the right ascension of celestial objects that are located on the meridian at that time View Time-Site will always display the last saved time and location entered while it is linking with the GPS Once current information has been received, it will update the displayed information If GPS is switched off or not present, the hand control will only display the last saved time and location
The Hand Control Menu
The “Hand Control” menu allows you to customize certain features of the NexStar+ hand control To access this menu, press the MENU button (#7 on the keypad) and use the scroll buttons to select “Hand Control” and press ENTER Use the scroll buttons to select from the following options:
· Lights Control: Independently adjust the brightness of the number keypad and the LCD
· Scrolling Menu: Adjust how fast words move across the face of the LCD
· Toggle Bold Font: Change the format of the font displayed on the LCD from normal to boldface
· Set Contrast: Use the scroll keys to adjust the contrast of the LCD
· Set Language: Change the displayed language on the LCD
Note: The Set Language feature may also appear the first time you use your new hand control You may also initiate it at any time by holding down the Option button (the Celestron logo) for 10 seconds while powering up the telescope
Scope Setup Menu
Setup Time-Site ­ Allows the user to customize the telescope’s display by changing time and location parameters (such as time zone and Daylight Savings)
Anti-backlash ­ All mechanical gears have a certain amount of backlash or play between the gears This play is evident by how long it takes for a star to move in the eyepiece when the hand control arrow buttons are pressed (especially when changing directions) The Advanced VX anti-backlash feature allows the user to compensate for backlash by inputting a value which quickly rewinds the motors just enough to eliminate the play between gears The amount of compensation needed depends on the slewing rate selected; the slower the slewing rate the longer it will take for the star to appear to move in the eyepiece There are two values for each axis, positive and negative:
· Positive is the amount of compensation applied when you press the button in order to get the gears moving quickly without a long pause

· Negative is the amount of compensation applied when you release the button, winding the motors back in the other direction to resume tracking
Normally, both values should be the same You will need to experiment with different values (from 0-99); a value between 20 and 50 is usually best for most visual observing, whereas a higher value may be necessary for photographic guiding
To set the anti-backlash value, scroll down to the anti-backlash option and press ENTER While viewing an object in the eyepiece, observe the responsiveness of each of the four arrow buttons Note which directions you see a pause in the star movement after the button has been pressed Working one axis at a time, adjust the backlash settings high enough to cause immediate movement without resulting in a pronounced jump when pressing or releasing the button Now, enter the same values for both positive and negative directions If you notice a jump when releasing the button but setting the values lower results in a pause when pressing the button, use the higher value for positive, but use the lower value for negative The telescope will remember these values and use them each time it is turned on until they are changed
Filter Limits ­ When an alignment is complete, the telescope automatically knows which celestial objects are above the horizon As a result, when scrolling through the database lists (or selecting the Tour function), the hand control will display only those objects that are known to be above the horizon when you are observing You can customize the object database by selecting altitude limits that are appropriate for your location and situation For example, if you are observing from a mountainous location where the horizon is partially obscured, you can set your minimum altitude limit to read +20° This will make sure that the hand control only displays objects that are higher in altitude than 20°
Tip: If you want to explore the entire object database, set the maximum altitude limit to 90° and the minimum limit to ­90° This will display every object in the database lists regardless of whether it is visible in the sky from your location
Direction Buttons ­ The direction a star appears to move in the eyepiece changes depending on which side of the meridian the telescope tube is on This can create confusion especially when guiding on a star when doing astroimaging To compensate for this, the direction of the drive control keys can be changed To reverse the button logic of the hand control, press the MENU button and select Direction Buttons from the Utilities menu Use the Up/Down arrow keys (10) to select either the azimuth (right ascension) or altitude (declination) button direction and press ENTER Select either positive or negative for both axes and press ENTER to save Setting the azimuth button direction to positive will move the telescope in the same direction that the telescope tracks (i e , towards the west) Setting the altitude buttons to positive will move the telescope counterclockwise along the DECLINATION axis

16 I ENGLISH

GoTo Approach ­ Lets the user define the direction that the telescope will approach when slewing to an object This allows the user the ability to minimize the effects of backlash when slewing from object to object Just like with Direction Buttons, setting GoTo Approach to positive will make the telescope approach an object from the same direction as tracking (west) for azimuth and counterclockwise in declination Declination GoTo approach will only apply while the telescope tube is on one side of the meridian Once the tube passes over to the other side of the meridian, the GoTo approach will need to be reversed
To change the GoTo approach direction, simply choose GoTo Approach from the Scope Setup menu, select either Altitude or Azimuth approach, choose positive or negative and press ENTER
Hint: In order to minimize the affect of gear backlash on pointing accuracy, the settings for Button Direction should ideally match the settings for GoTo Approach By default, using the up and right direction buttons to center alignment stars will automatically eliminate much of the backlash in the gears If you change the GoTo approach of your telescope, it is not necessary to change the Button Direction as well Simply take notice of the direction the telescope moves when completing its final GoTo approach If the telescope approaches its alignment star from the west (negative azimuth) and clockwise (negative altitude) then make sure that the buttons used to center the alignment stars also move the telescope in the same directions
Autoguide Rate ­ Allows the user to set an autoguide rate as a percentage of sidereal rate This is helpful when calibrating your telescope to a CCD autoguider for long exposure astroimaging
OTA Orientation ­ Some users may wish to use an optional tandem bar adapter which allows you to attach two optical tubes to the mount at the same time When most tandem bars are attached to a mount, the optical tubes are positioned at a 90° angle from the standard configuration In order for the mount to be successfully aligned with the stars, it must know that a tandem bar is being used and in which direction the optical tube(s) are positioned (East or West) when beginning an alignment The tandem option must be set before beginning any of the initial star alignments To set this option, go to the Scope Setup menu, select the Tandem option and press ENTER Then select from one of the following options:
· East ­ If the attached optical tubes are facing towards the east when the declination index makers are align, select East
· West ­ If the attached optical tubes are facing towards the west when the declination index makers are align, select West
· Normal ­ If the tandem bar is no longer being used, select “normal” to turn off this feature
Meridian ­ This feature instructs the mount on how to

respond when it is slewing to objects that are accessible from both sides of the meridian The meridian feature allows the telescope tube to remain on a desired side of the mount when slewing, and continue to track according to the R A slew limits the user has set See R A Limits below The meridian feature allows for four choices:
· Favor Current ­ Allows the mount to favor whatever side of the mount that it is currently on when slewing to objects close to the meridian For example, if your R A slew limits are set to allow the mount to track 10° past the meridian, then the telescope will continue to stay on its current side of the meridian when slewing to objects that are as far as 10° beyond your Meridian
· Favor West ­ If the target object is accessible from both sides of the mount, selecting “Favor West” instructs the mount to point to the object as if it were on the west side of the meridian The optical tube will then be positioned on the east side of the mount and pointing west
· Favor East ­ If the target object is accessible from both sides of the mount, selecting “Favor East” instructs the mount to point to the object as if it were on the east side of the meridian The optical tube will then be positioned on the west side of the mount and pointing east
· Disable ­ This is the default setting, which instructs the mount to always swing around to the other side of the pier as required to view objects on the opposite side of the meridian However, once at the desired object, the mount will continue to track past the meridian according to the R A slew limits that have been set
Mount Settings ­ Once the mount settings have been calibrated (see Utilities section below) the values are stored and displayed in the hand control It is not recommended that the calibration values be changed However, each setting can be changed if necessary to improve the performance of the telescope
· Cone Value ­ This is the cone error value set when Utilities/Calibrate Mount/DEC Switch ­ Cone is carried out
· DEC Index ­ This is the declination index error value that is stored when calibration stars are added after your initial star alignment
· R.A. Index ­ This is the R A index error value set when Utilities/Calibrate Mount/R A Switch is carried out
R.A. Limits ­ Sets the limits that the telescope can slew or track in Right Ascension (R A ) before stopping The slew limits are represented in degrees and by default set to 0°, being the position of the telescope when the counterweight bar is extended out horizontally However, the slew limits can be customized depending on your needs For example, if you are using CCD imaging equipment that has cables that are not long enough to move with the telescope as it slews across the sky, you can adjust the slew limit on the side of the mount that is restricted by the cables, and command the mount the stop slewing before it reaches this point Or if you are taking an image of an object that has just crossed the meridian, you can set the limit to allow the mount to continue

ENGLISH I 17

tracking in the same direction past the meridian without the need to “flip” the telescope around to the opposite side of the mount (see Meridian feature above) Using the first example above, the user could slew the telescope in R A (azimuth) until it reaches the point that the cables are extended to their maximum Then by displaying the telescope’s azimuth in this position (by looking at Get Axis Position under the Utilities menu), you can determine the telescope’s azimuth at its most extended position Enter this azimuth reading for either the maximum or minimum azimuth slew limit to ensure that the telescope will not slew beyond this point The telescope slew limits can be set to automatically stop anywhere between 40° above level to 20° below level To set the R A slew limit select the following:
· R.A. East Limit ­ Enter a number between +40° to -20° to define the slew limit when the tube is on the east side of the mount
· R.A. West Limit ­ Enter a number between +40° to -20° to define the slew limit when the tube is on the west side of the mount
· Disable Limits ­ This disables any pre-defined values that have been entered and allows the mount to track the maximum amount past the meridian (i e , -20° on both sides)

Calibrate Mount ­ In order to optimize the performance and pointing accuracy of the telescope, the mount has built-in calibration routines allowing it to compensate for mechanical variation inherent in every German equatorial mount Each calibration is completely automatic and in most cases only needs to be performed once It is highly recommended that you take a few minutes to go through the mount calibration procedures
· R.A. Switch ­ This procedure records the offset error when the right ascension index mark is aligned at start-up Calibrating the R A Index will improve the accuracy of your initial star alignments when aligning the telescope in the future
· GoTo Calibration ­ GoTo Calibration is a useful tool when attaching heavy visual or photographic accessories to the telescope GoTo Calibration calculates the amount of distance and time it takes for the mount to complete its final slow GoTo when slewing to an object Changing the balance of the telescope can prolong the time it takes to complete the final slew GoTo Calibration takes into account any slight imbalances and changes the final GoTo distance to compensate
Home Position ­ The telescope’s “home” position is a user-definable position that is used to store the telescope when not in use The home position is useful when storing the telescope in a permanent observatory facility By default the Home position is the same as the index position used when aligning the mount

To set the Home position for your mount, simply use the arrow buttons on the hand control to move the telescope mount to the desired position Select the Set option and press Enter

Select the GoTo option to slew the telescope back to the Home position at any time

Warning: For the telescope to be able to slew to a star from the direction that minimizes the amount of backlash in the gears, it may be necessary for the telescope to slew beyond the specified slew limit in order to approach the star from the correct direction This can limit your ability to slew to an object by as much as 6° from the R A slew limit set in the hand control If this proves to be a problem, the direction that the telescope takes to center an object can be changed To change the telescopes slewing direction, see GoTo Approach under the Scope Setup menu
Custom Rate 9 ­ This allows you to customize the speed at which the mount slews to a target You can set the R A and Dec axes individually

Factory Settings ­ Returns the hand control to its original factory settings Parameters such as backlash compensation values, initial date and time, longitude/latitude, along with slew and filter limits will be reset However, stored parameters such as user defined objects will remain saved even when Factory Settings is selected The hand control will ask you to press the “0” key before returning to the factory default setting
Version ­ Selecting this option will allow you to see the current version number of the hand control and motor control The first set of numbers indicate the hand control software version For the motor control, the hand control will display two sets of numbers; the first numbers are for azimuth and the second set are for altitude

Utilities Menu
Scrolling through the MENU (9) options will also provide access to several advanced utility functions within the telescope such as: Calibrate Mount, Hibernate and many others

Get Axis Position ­ Displays the relative altitude and azimuth for the current position of the telescope
GoTo Axis Position ­ Allows you to enter a specific relative altitude and azimuth position and slew to it

18 I ENGLISH

Hibernate ­ Hibernate allows the telescope to be completely powered down and still retain its alignment when turned back on This not only saves power, but is ideal for those that have their telescope permanently mounted or leave their telescope in one location for long periods of time To place your telescope in Hibernate mode:
1 Select Hibernate from the Utility Menu
2 Move the telescope to a desired position and press ENTER
3 Power off the telescope Remember to never move your telescope manually while in Hibernate mode
Once the telescope is powered on again, the display will read Wake Up After pressing Enter, you have the option of scrolling through the time/site information to confirm the current setting Press ENTER to wake up the telescope
Hint: Pressing BACK at the Wake Up screen allows you to explore many of the features of the hand control without waking the telescope up from hibernate mode To wake up the telescope after BACK has been pressed, select Hibernate from the Utility menu and press ENTER Do not use the direction buttons to move the telescope while in hibernate mode
Sun Menu
For safety purposes, the Sun will not be displayed as a database object unless it is first enabled To enable the Sun, go to the Sun Menu and press ENTER The Sun will now be displayed in the Planets catalog and can be used as an alignment object when using the Solar System Alignment method To remove the Sun from displaying on the hand control, once again select the Sun Menu from the Utilities Menu and press ENTER
Set Mount Position
The Set Mount Position menu can be used to maintain your alignment in cases where you wish to disengage the clutches or similar situation For instance, you might use this feature if you needed to rebalance the mount after having completed an alignment To set the mount position, simply slew to a bright star in the named star list and select Set Mount Position The hand control will sync on the star by asking you to center the star in the eyepiece and pressing the Align button Once synced on the star, you are free to manually move the mount in both axes in order to rebalance When you are ready to slew the telescope to your next object, just remember to manually return the tube to the same bright star and carefully center it in the eyepiece Using this tool will invalidate the PEC index
Turn On/Off GPS ­ If using your telescope with the optional SkySync GPS accessory, you will need to turn the GPS on the first time you use the accessory If you want to use the telescope’s database to find the coordinates of a celestial object for a future or past dates, you will need to turn the GPS off in order to manually enter a time other than the present

Turn On/Off RTC ­ Allows you to turn off the telescope’s internal real time clock When aligning, the telescope still receives time information from the RTC If you want to use the hand control database to find the coordinates of a celestial object for a future or past dates, you will need to turn the RTC off in order to manually enter a time other than the present
Periodic Error Correction (PEC) ­ PEC is designed to improve photographic quality by reducing the amplitude of the worm gear errors and improving the tracking accuracy of the drive This feature is for advanced astrophotography and is used when your telescope is accurately polar aligned For more information on using PEC, refer to the section of the manual on “Astroimaging”
User Objects Menu
Your telescope can store up to 400 different user-defined objects in its memory The objects can be daytime land objects or an interesting celestial object that you discover that is not included in the regular database There are several ways to save an object to memory depending on what type of object it is:
GoTo Object: To go to any of the user defined-objects stored in the database, scroll down to either “GoTo Sky Obj” or “GoTo Land Obj” and enter the number of the object you wish to select and press ENTER The telescope will automatically retrieve and display the coordinates before slewing to the object
Save Sky Object: Your telescope stores celestial objects to its database by saving its right ascension and declination coordinates in the sky This way the same object can be found each time the telescope is aligned Once a desired object is centered in the eyepiece, simply scroll to the “Save Sky Obj” command and press ENTER The display will ask you to enter a number between 1 and 200 to identify the object Press ENTER again to save this object to the database
Save Database (Db)
· Object: This feature allows you to create your own custom tour of database objects by allowing you to record the current position of the telescope and save the name of the object by selecting it from any one of the database catalogs These objects then can be accessed by selecting GoTo Sky Object
· Enter R.A. – Dec: You can also store a specific set of coordinates for an object just by entering the R A and declination for that object Scroll to the “Enter RA-DEC” command and press ENTER The display will then ask you to enter first the R A and then the declination of the desired object
· Save Land Object: The telescope can also be used as a spotting scope on terrestrial objects Fixed land objects can be stored by saving their altitude and azimuth relative to the location of the telescope at the time of observing Since these objects are relative to the location of the

ENGLISH I 19

telescope, they are only valid for that exact location To save land objects, once again center the desired object in the eyepiece Scroll down to the “Save Land Obj” command and press ENTER The display will ask you to enter a number between 1 and 200 to identify the object Press ENTER again to save this object to the database
To replace the contents of any of the user defined-objects, simply save a new object using one of the existing identification numbers; the telescope will replace the previous user-defined object with the current one
Get R.A./DEC – Displays the right ascension and declination for the current position of the telescope
Goto R.A./Dec – Allows you to input a specific R A and declination and slew to it
Hint: To store a set of coordinates (R A /Dec) permanently into the database, save it as a User-Defined Object as described above

To use Precise GoTo:
1 Press the MENU button and use the Up/Down keys to select Precise GoTo
· Choose Database to select the object that you want to observe from any of the database catalogs listed or;
· Choose R A /DEC to enter a set of celestial coordinates that you wish to slew to
2 Once the desired object is selected, the hand control will search out and display the closest bright star to your desired object Press ENTER to slew to the bright alignment star
3 Use the direction buttons to carefully center the alignment star in the eyepiece
4 Press ENTER to slew to the desired object

Identify
Identify Mode will search any of the mount’s database catalogs or lists and display the name and offset distances to the nearest matching objects This feature can serve two purposes First, it can be used to identify an unknown object in the field of view of your eyepiece Additionally, Identify Mode can be used to find other celestial objects that are close to the objects you are currently observing For example, if your telescope is pointed at the brightest star in the constellation Lyra, choosing Identify and then searching the Named Star catalog will no doubt return the star Vega as the star you are observing However, by selecting Identify and searching by the Named Object or Messier catalogs, the hand control will let you know that the Ring Nebula (M57) is approximately 6° from your current position Searching the Double Star catalog will reveal that Epsilon Lyrae is only 1° away from Vega To use the Identify feature:
· Press the Menu button and select the Identify option
· Use the Up/Down scroll keys to select the catalog that you would like to search
· Press ENTER to begin the search
Note: Some of the databases contain thousands of objects and can therefore take several minutes to return the closest objects

Precise GoTo
The mount has a Precise GoTo function that can assist in finding extremely faint objects and centering objects closer to the center of the field of view for astroimaging Precise GoTo automatically searches out the closest bright star to the desired object and asks the user to carefully center the star in the eyepiece The hand control then calculates the small difference between its GoTo position and its centered position Using this offset, the mount will then slew to the desired object with enhanced accuracy

20 I ENGLISH

Advanced VX Main Menu Tree

Menu

Tracking
View Time-Site Hand Control
Scope Setup Utilities
User Objects
Get RA-Dec GoTo RA-Dec
Identify Precise GoTo

Mode

EQ North

EQ South

Off

Rate

Sidereal

Solar

Lunar

Saved Site

Light Control

Keypad Level

Display Level

Scrolling Menu

Toggle Bold Font

Set Contrast

Set Language

See Diagram – Next Page

See Diagram – Next Page

GoTo Sky Objects

Save Sky Objects

Save Db Objects

Enter RA & Dec

GoTo Land Object

Save Land Object

ENGLISH I 21

Advanced VX Main Menu Tree

Scope Setup

Setup Time-Site Anti-Backlash
Filter Limits Direction Button GoTo Approach Autoguide Rates OTA Orientation
Meridian
Mount Settings RA Limits
Custom Rate 9

Custom Site City Database
RA Positive RA Negative Dec Positive Dec Negative
RA Button Dec Button RA Approach Dec Approach
RA Rate Dec Rate Normal
East West Disabled Favor Current Favor West Favor East Cone Value RA East Limit RA West Limit Disable Limits RA Axis

Dec Axis

Utilities

Calibrate Mount Home Position
Factory Setting Version
Get Axis Position GoTo Axis Position
Hibernate Sun Menu Set Mount Position Turn on/off GPS Turn on/off RTC
PEC

GoTo Set

Enable Set Rate Enable Set Rate

22 I ENGLISH

Optical Tube Assemblies
Depending on the telescope kit you purchased, you may have received one of the following optical tubes This section of the manual will walk you through the setup of the basic types

Kit # Optical Design Diameter Focal Length Eyepiece Finderscope Star Diagonal Mount Tripod Counterweights Tube Length Tube Weight

22020 Refractor 6″ (150mm) 1200mm f/8 20mm (60x) – 1 25″ 9×50 90° – 1 25″ Advanced VX 2″ Stainless Steel 2x 12 lb 51″ (128 cm) 19 lb

32054 Newtonian 6″ (150mm) 750mm f/5 20mm (38x) – 1 25″ 6×30 Advanced VX 2″ Stainless Steel 1x 12 lb 27″ (69 cm) 10 lb

32062 Newtonian 8″ (200mm) 1000mm f/5 20mm (50x) – 1 25″ 9×50 Advanced VX 2″ Stainless Steel 2x 12 lb 27″ (69 cm) 14 lb

12031 Edge HD 8″ (203mm) 2032mm f/10 40mm (51x) – 1 25″ 9×50 90° – 1 25″ Advanced VX 2″ Stainless Steel 1x 12 lb 17″ (43 cm) 13 lb

Kit # Optical Design Diameter Focal Length Eyepiece Finderscope Star Diagonal Mount Tripod Counterweights Tube Length Tube Weight

12025 Schmidt-Cassegrain 5″ (125mm) 1250mm f/10 25mm (50x) – 1 25″ 6×30 90° – 1 25″ Advanced VX 2″ Stainless Steel 1x 12 lb 13″ (33 cm) 10 lb

12079 Schmidt-Cassegrain 6″ (150mm) 1500mm f/10 20mm (75x) – 1 25″ 6×30 90° – 1 25″ Advanced VX 2″ Stainless Steel 1x 12 lb 16″ (40 cm) 10 lb

12026 Schmidt-Cassegrain 8″ (203mm) 2032mm f/10 25mm (81x) – 1 25″ 6×30 90° – 1 25″ Advanced VX 2″ Stainless Steel 1x 12 lb 17″ (43 cm) 12 lb

12046 Schmidt-Cassegrain 9-1/4″ (235mm) 2350mm f/10 25mm (94x) – 1 25″ 6×30 90° – 1 25″ Advanced VX 2″ Stainless Steel 2x 12 lb 22″ (56 cm) 21 lb

Kit #
Optical Design Diameter Focal Length Eyepiece Finderscope Star Diagonal Mount Tripod Counterweights Tube Length Tube Weight

12067
Schmidt-Cassegrain 11″ (280mm) 2800mm f/10 40mm (70x) – 1 25″ 9×50 90° – 1 25″ Advanced VX 2″ Stainless Steel 3x 12 lb 24″ (61 cm) 28 lb

12033
EdgeHD 10 7″ (271 78mm) 2350mm f/10 23mm (102x) – 0 91″ 9×50 2″ with 1 25″ adapter Advanced VX 2″ Stainless Steel 2x 12 lb 22″ (56 cm) 21 lb

ENGLISH I 23

Setting Up the Refractor (#21020)

3 Tighten the set screw to hold the eyepiece in place

Installing the Finderscope
To install the finderscope onto the telescope, you must first mount the finderscope through the finder bracket and then attach it to the telescope Toward the rear of the telescope tube, near the focusing assembly, there is a small bracket with a set screw in it This is where the finderscope bracket will be mounted To install the finderscope:

Focuser Tension Screw 1 25 Eyepiece Adapter

1 Slide the rubber O-ring over the eyepiece end of the finderscope and roll it 2/3 of the way up the finderscope
2 Insert the eyepiece end of the finderscope through the bracket until the O-ring presses tightly between the finder and the inside of the bracket
Finderscope

Finder Bracket

Mounting Bracket Set Screw

2″ Focuser Barrel Focuser Knob

T-Adapter Thread

To remove the eyepiece, loosen the set screw on the focuser and slide the eyepiece out You can replace it with another ocular
Eyepieces are commonly referred to by focal length and barrel diameter The focal length of each eyepiece is printed on the eyepiece barrel The longer the focal length (i e , the larger the number), the lower the eyepiece magnification (i e , power) The shorter the focal length (i e , the smaller the number), the higher the eyepiece magnification Generally, you will use low-to-moderate power when viewing

3 Tighten the adjustment screws until they make contact with the finderscope body
4 Locate the mounting bracket near the rear (open) end of the telescope
5 Loosen the set screw on the mounting bracket on the telescope
6 Slide the finder bracket (attached to the finderscope) into the mounting bracket on the telescope
7 The finderscope bracket will slide in from the back The finderscope should be oriented so that the objective lens is toward the front (open) end of the telescope
8 Tighten the set screw on the mounting bracket to hold the finderscope in place
Installing the Eyepieces
The eyepiece, or ocular as it is also called, is an optical element that magnifies the image focused by the telescope Without the eyepiece, it would be impossible to use the telescope visually The eyepiece fits directly into the focuser To attach an ocular:
1 Loosen the set screw on the eyepiece adapter so that it does not obstruct the inner diameter of the barrel
2 Slide the chrome portion of the eyepiece into the focuser

Your refracting telescope can use eyepieces with both a 1 25″ and 2″ barrel diameters To use a 2″ barrel eyepiece, the 1 25″ eyepiece adapter must first be removed To do this, simply loosen the two chrome thumbscrews located around the focuser barrel and remove the 1 25″ adapter Once removed, a 2″ eyepiece or accessory can be inserted directly into the focuser barrel and secured with the two thumb screws
Your telescope comes with a 1 25″ star diagonal This diagonal can be inserted into the end of the 1 25″ adapter allowing you to use 1 25″ eyepieces at a more comfortable angle when viewing near the zenith
Setting Up the Newtonian Reflector
(#32054 & #32062)
Installing the Finderscope
To install the finderscope onto the telescope you must first mount the finderscope through the finder bracket and then attach it to the telescope Toward the front of the telescope tube, near the focusing assembly, there is a small bracket with a set screw in it This is where the finderscope bracket will be mounted To install the finderscope:
1 Slide the rubber O-ring over the eyepiece end of the finderscope and roll it 2/3 of the way up the finderscope
2 Insert the eyepiece end of the finderscope through the bracket until the O-ring presses tightly between the finder and the inside of the bracket
3 Tighten the adjustment screws until they make contact with the finderscope body

24 I ENGLISH

4 Locate the mounting bracket near the front (open) end of the telescope
5 Loosen the set screw on the mounting bracket on the telescope
6 Slide the finder bracket (attached to the finderscope) into the mounting bracket on the telescope
7 The finderscope bracket will slide in from the back The finderscope should be oriented so that the objective lens is toward the front (open) end of the telescope
8 Tighten the set screw on the mounting bracket to hold the finderscope in place
Installing the Eyepieces
The eyepiece, or ocular as it is also called, is an optical element that magnifies the image focused by the telescope Without the eyepiece, it would be impossible to use the telescope visually The eyepiece fits directly into the eyepiece holder To attach an ocular:
1 Loosen the set screw on the eyepieceholder so that it does not obstruct the inner diameter of the eyepiece holder
2 Slide the chrome portion of the eyepiece into the eyepiece holder
3 Tighten the set screw to hold the eyepiece in place

Chrome Portion Eyepiece Holder

Eyepiece

Setting up the EdgeHD and SchmidtCassegrain Optical Tubes (#12031, #12033,

12079, #12025, #12026, #12046 and #12067)

Installing the Star Diagonal The star diagonal is a prism that diverts the light at a right angle to the light path of the telescope This allows you to observe in positions that are physically more comfortable than if you looked straight through To attach the star diagonal onto the optical tube:
1 Turn the set screw on the visual back until its tip no longer extends into (i e , obstructs) the inner diameter of the visual back
2 Slide the chrome portion of the star diagonal into the visual back
3 Tighten the set screw on the visual back to hold the star diagonal in place
Eyepiece

Visual Back

Star Diagonal

If you wish to change the orientation of the star diagonal, loosen the set screw on the visual back until the star diagonal rotates freely Rotate the diagonal to the desired position and tighten the set screw

To remove the eyepiece, loosen the setscrew on the eyepiece holder and slide the eyepiece out You can replace it with another ocular Eyepieces are commonly referred to by focal length which is printed on the eyepiece barrel The longer the focal length (i e , the larger the number), the lower the eyepiece magnification The shorter the focal length (i e , the smaller the number), the higher the eyepiece magnification Generally, you will use low-to-moderate power when viewing
If you have the 8″ Newtonian optical tube (#32062), your telescope can use eyepieces with both a 1 25″ and 2″ barrel diameters To use a 2″ barrel eyepiece, the 1 25″ eyepiece adapter must first be removed and replaced with the included 2″ eyepiece adapter To do this, simply loosen the two chrome thumbscrews located around the focuser barrel and remove the 1 25″ adapter Once removed, a 2″ eyepiece adapter can be inserted directly into the focuser barrel and secured with the two thumb screws

Installing the Eyepiece
The eyepiece, or ocular, is an optical element that magnifies the image focused by the telescope The eyepiece fits into either the visual back directly or the star diagonal To install an eyepiece:
1 Loosen the set screw on the star diagonal until the tip no longer extends into the inner diameter of the eyepiece end of the diagonal
2 Slide the chrome portion of the eyepiece into the star diagonal
3 Tighten the set screw on the star diagonal to hold the eyepiece in place
To remove the eyepiece, loosen the set screw on the star diagonal and slide the eyepiece out You can replace it with another eyepiece (purchased separately)
Eyepieces are commonly referred to by focal length and barrel diameter The focal length of each eyepiece is printed on the eyepiece barrel The longer the focal length (i e , the

ENGLISH I 25

larger the number), the lower the eyepiece magnification The shorter the focal length (i e , the smaller the number), the higher the magnification Generally, you will use lowto-moderate power when viewing For more information on how to determine power, see the section on “Calculating Magnification ”
Installing the 6×30 Finderscope
The 5″, 6″, 8″ and 9 25″ Schmidt Cassegrain telescopes come with 6×30 finderscopes used to help you locate and center objects in the main field of your telescope To accomplish this, the finder has a built-in cross-hair reticle that shows the optical center of the finderscope To install the finderscope:
1 Attach the bracket to the optical tube To do this, place the curved portion of the bracket with the slot over the two holes in the rear cell The bracket should be oriented so that the rings that hold the finder are over the telescope tube, not the rear cell Start threading the screws in by hand and tighten fully with a screwdriver
Finderscope Nylon Adjustment Screw
Finder Bracket
Rear Cell
2 Partially thread-in the three nylon thumbscrews that hold the finder in place inside the bracket Tighten the screws until the nylon heads are flush with the inner diameter of the bracket ring Do NOT thread them in completely, or they will interfere with the placement of the finder (Having the screws in place when the finder is installed will be easier than trying to insert the screws after the finder has been installed)
3 Slide the rubber O-ring over the back of the finder (it will NOT fit over the objective end of the finder) It may need to be stretched a little Once on the main body of the finder, slide it up about one inch from the end of the finder
4 Rotate the finder until one cross hair is parallel to the R A axis and the other is parallel to the DEC axis
5 Slide the eyepiece end of the finder into the front of the bracket
6 Slightly tighten the three nylon thumb screws on the front ring of the bracket to hold the finder in place
7 Once on, push the finder back until the O-ring is snug inside the back ring of the finder bracket
8 Hand tighten the three nylon tipped thumb screws until snug

Installing the 9×50 Finderscope
The 8″ EdgeHD and the 11″ Schmidt-Cassegrain telescopes come with 9×50 finderscopes used to help you locate and center objects in the main field of your telescope To accomplish this, the finder has a built-in cross-hair reticle that shows the optical center of the finderscope The finderscope must first be mounted in the included quick-release bracket then attached to the rear cell of the telescope To install the finderscope:
1 Locate the finderscope mounting bracket attached to the bottom portion of the finder bracket Loosen the two thumb screws to slide the mounting bracket from the finderscope bracket
2 Find the two holes in the rear cell of the telescope on the top left, when looking from the back of the tube
3 Place the mounting bracket over the two holes of the rear cell on the optical tube
4 Insert the screws through the bracket and into the rear cell
WARNING: If you remove the mounting bracket, do not completely thread the screws back into the rear cell of the telescope The screws may be long enough to obstruct the movement of, and possibly damage, the primary mirror
With the bracket firmly attached to the telescope, you are ready to attach the finder to the bracket
1 Slide the O-Ring over the back of the finderscope and position it on the tube toward the objective end of the finderscope
2 Slide the eyepiece end of the finderscope into the front ring of the bracket (the front ring is the one without the adjustment screws), then through the back ring It may be necessary to push down the spring loaded pivot screw so that the finder will pass through the back ring
3 Push the finder back until the O-Ring is snug inside the front ring of the finder bracket
4 Hand tighten the two alignment thumb screws until they make contact with the finderscope

Pivot Screws

Alignment Screws

Quick Release Screws

26 I ENGLISH

Polar Aligning the Mount

Latitude Scales
The easiest way to polar align a telescope is with a latitude scale Unlike other methods that require you to find the celestial pole by identifying certain stars near it, this method works off of a known constant to determine how high the polar axis should be pointed The Advanced VX mount can be adjusted from 7 to 77 degrees

Aligning the Finderscope
The finderscope is adjusted using two adjustment screws, located on the top and on the right (when looking though the finder) of the finder bracket and a spring-loaded pivot screw (located on the left side of the bracket) This allows you to turn the top adjustment screw to move the finderscope up and down, and turn the right adjustment screw to move the finderscope right to left The spring-loaded pivot screw puts constant pressure on the finder so that the adjustment screws are always making contact with the finder

The constant, mentioned above, is a relationship between your latitude and the angular distance the celestial pole is above the northern (or southern) horizon; the angular distance from the northern horizon to the north celestial pole is always equal to your latitude To illustrate this, imagine that you are standing on the North Pole, latitude +90° The north celestial pole, which has a declination of +90°, would be directly overhead (i e , 90° above the horizon) Now, let’s say that you move one degree south — your latitude is now +89° and the celestial pole is no longer directly overhead It has moved one degree closer toward the northern horizon This means the pole is now 89° above the northern horizon If you move one degree further south, the same thing happens again You would have to travel 70 miles north or south to change your latitude by one degree As you can see from this example, the distance from the northern horizon to the celestial pole is always equal to your latitude

To make the alignment process a little easier, you should perform this task in the daytime when it is easier to locate objects in the telescope without the finder

To align the finder:

1 Choose a conspicuous object that is in excess of one mile away This will eliminate any possible parallax effect between the telescope and the finder
2 Point your telescope at the object you selected and center it in the main optics of the telescope
3 Lock the azimuth and altitude clamps to hold the telescope in place
4 Check the finder to see where the object is located in the field of view
5 Adjust the thumb screws on the finder bracket until the cross hairs are centered on the target
Removing the Lens Cap
The EdgeHD and Schmidt-Cassegrain telescopes utilize a lens cap with a bayonet-type locking mechanism to hold it in place To remove the lens cap, hold the cover firmly and rotate the outer edge 1/2″ counterclockwise and pull off

If you are observing from Los Angeles, which has latitude of 34°, then the celestial pole is 34° above the northern horizon All a latitude scale does then is to point the polar axis of the telescope at the right elevation above the northern (or southern) horizon
To align your telescope:
1 Make sure the polar axis of the mount is pointing due north Use a landmark that you know faces north
2 Level the tripod
3 Adjust the mount in altitude until the latitude indicator points to your latitude Moving the mount affects the angle the polar axis is pointing For specific information on adjusting the equatorial mount, please see the section “Adjusting the Mount”

ENGLISH I 27

This method can be done in daylight, thus eliminating the need to attempt in the dark Although this method does NOT put you directly on the pole, it will limit the number of corrections you will make when tracking an object It will also be accurate enough for short exposure prime focus planetary imaging (a couple of seconds) and short exposure piggyback astroimaging (a couple of minutes)
Polar Align using the Hand Control
The Advanced VX mount has a polar alignment function called “All-Star” Polar Alignment that will help you polar align your telescope for increased tracking precision and for astroimaging This feature allows you to choose any bright alignment star to assist in accurately aligning your telescope’s mount with the North Celestial Pole Before using the Polar Align feature, the scope must first be roughly pointed towards north and should be aligned with three stars in the sky See the “Latitude Scale” section for help with finding north and adjusting the mounts latitude
Once your telescope is aligned on two stars and at least one additional calibration star, slew the telescope to any bright star in its Named Star database list For best results, choose a polar alignment star that is high in the sky and near the Meridian Try to avoid stars that are close to the west/ east horizon, directly overhead or too near the celestial pole Once completed, press the Align button and use the Up/ Down buttons on the hand controller to select Polar Align from the list
Align Mount ­ After performing a two star alignment with one calibration star and slewing your telescope to any bright star in the telescope’s database, select the “Align Mount” option The telescope will then slew away from and then back to the same star
1 The hand control will ask you to re-center the star in the finderscope and press ENTER
2 The hand control will ask you to accurately center the star in your eyepiece and press ALIGN The telescope will then “sync” on this star and slew to the position that the star should be if it were accurately polar aligned
Note: For the most accurate alignment, it is best to use a reticle eyepiece or a high power eyepiece to precisely center the star in the field of view
3 Use the mount’s latitude and azimuth adjustments to place the star in the center of the eyepiece Do not use the direction buttons on the hand control to position the star Once the star is centered in the eyepiece, press ENTER; the polar axis should now be pointed towards the North Celestial Pole
Updating your Star Alignment
After polar alignment, it is a good idea to check the pointing accuracy of the telescope to see how much it may have been affected by moving the mount Since the polar alignment process requires you to “sync” the telescope on a bright star before you begin, it will be necessary to undo the sync before re- aligning To undo the sync:

· Press the Align button and use the Up/Down buttons on the hand controller to select Undo Sync from the list, and press Enter The message Complete will display on the LCD
To re-align your telescope:
1 Slew the telescope to one of the original alignment stars or another bright star if the original alignment stars are no longer in a convenient location Press the Align button and use the Up/Down buttons on the hand controller to select Alignment Stars from the list
2 The hand control will ask you which of the original alignment stars you wish to replace Use the Up/Down buttons to select the desired star and press Enter
3 Once again, center the star in the finderscope and press Enter
4 Center the star in the eyepiece and Press Align
5 Repeat the process on a second alignment star
For additional all-sky pointing accuracy, it is a good idea to align on at least one additional calibration star located on the opposite side of the Meridian To add calibration stars:
1 Slew the telescope to a bright star on the opposite side of the Meridian from your two alignment stars
2 Press the Align button and use the Up/Down buttons on the hand controller to select Calib Stars from the list, and press Enter
3 Align the star in the finderscope and then in the eyepiece as you did with the alignment stars
Display Align ­ The user can now display the polar alignment error in the RA and DEC axes These values show how close the mount is pointed at the celestial pole base on how accurately the user centered the alignment star with the hand control and with the mount adjustment To display the alignment error:
· Press the Align button and use the Up/Down buttons on the hand controller to select Display Align from the list, and press Enter
Long Exposure Prime Focus Photography
This is the last form of celestial photography to be attempted after others have been mastered It is intended primarily for deep sky objects, that is, objects outside our solar system including star clusters, nebulae, and galaxies While it may seem that high magnification is required for these objects, just the opposite is true Most of these objects cover large angular areas and fit nicely into the prime focus field of your telescope The brightness of these objects, however, requires long exposure times and, as a result, are rather difficult
There are several techniques for this type of photography, and the one chosen will determine the standard accessories needed The best method for long exposure deep sky astrophotography is with an optional off-axis guider

28 I ENGLISH

This device allows you to photograph and guide through the telescope simultaneously In addition, you will need a T-Ring to attach your camera to the off-axis guider
Other equipment needs include an autoguider, which is a small camera that attaches to the off-axis guider and keeps your guide star centered while you are imaging with your main camera Here is a brief summary of the technique
1 Polar align the telescope For more information on polar aligning, see the Polar Alignment section earlier in the manual
2 Remove all visual accessories
3 Thread the off-axis guider onto your telescope
4 Thread the T-Ring onto the off-axis guider
5 Mount your camera body onto the T-Ring the same as you would any other lens
6 Set the shutter speed to the “B” setting
7 Focus the telescope on a star
8 Center your subject in the field of your camera
9 Using your autoguider, find a suitable guide star in the telescope field This can be the most time-consuming part of the process
10 Open the shutter using a cable release
11 Monitor your guide star for the duration of the exposure using the buttons on the hand controller to make the needed corrections
12 Close the camera’s shutter
Periodic Error Correction (PEC)
Periodic Error Correction, or PEC for short, is a system that improves the tracking accuracy of the drive by reducing the number of user corrections needed to keep a guide star centered in the eyepiece PEC is designed to improve imaging quality by reducing the amplitude of the worm errors Using the PEC function is a three-step process First, the Advanced VX mount needs to know the current position of its worm gear, so it has a reference when playing back the recorded error Next, you must guide using an autoguider for at least 10 minutes during which time the system records the correction you make (It takes the worm gear 10 minutes to make one complete revolution) This “teaches” the PEC chip the characteristics of the worm The periodic error of the worm gear drive will be stored in the PEC chip and used to correct periodic error The last step is to play back the corrections you made during the recording phase Keep in mind, this feature is for advanced astrophotography and still requires careful guiding since all telescope drives have some periodic error

1 Find a bright star relatively close to the object you want to image
2 Insert the autoguider into the eyepiece holder of your telescope Orient the guider so that one axis of the sensor is parallel to the declination axis while the other is parallel to the R A axis
3 Focus the telescope, and study the periodic movement
4 Plug the autoguider cable into the autoguider port on the mount’s electronics panel
5 To begin recording the drive’s periodic error, press the MENU button and select PEC from the Utilities menu Use the Up/Down scroll buttons to display the Record option and press ENTER When you are ready to record, press the ENTER button again to begin You will have 5 seconds before the system starts to record The first time each observing session that PEC record or play is selected, the worm gear must rotate in order to mark its starting position If the worm gear rotation moves your guide star outside the field of view of the eyepiece, it will have to be re-centered before the recording begins
Note: Once the worm gear is indexed, it will not need to be positioned again until the telescope is turned off To give yourself more time to prepare for guiding, it may be necessary to restart PEC recording after the worm gear has found its index
6 After 10 minutes, PEC will automatically stop recording
7 Point the telescope at the object you want to image and center the guide star on the illuminated cross hairs You are ready to play back the periodic error correction
8 Once the drive’s periodic error has been recorded, use the Playback function to begin playing back the correction for future imaging guiding If you want to re-record the periodic error, select Record and repeat the recording processes again The previously recorded information will be replaced with the current information Repeat steps 7 and 8 to playback the PEC corrections for your next object
Does the PEC function make unguided astroimaging possible? Yes and no For solar (filtered), lunar and piggyback (up to 200mm), the answer is yes However, even with PEC, autoguiding is still mandatory for long exposure, deep sky astroimaging

Using Periodic Error Correction
Once the telescope has been properly polar aligned, select PEC from the Utilities menu and select the Record option Here’s how to use the PEC function:

ENGLISH I 29

Appendix A ­ Advanced VX Mount Technical Specifications

Payload Capacity (excluding counterweight) Optical Tube Mounting System
Computerized Hand Control
Database
Slew Speeds Tracking Modes Tracking Rates
Alignment Procedures
Motor Type Power Requirements Latitude Range PEC GPS Backlash Compensation Internal Real-Time Clock
Available Ports
Setting Circles Polar Axis Scope Counterweight Shaft Length Counterweight Shaft Diameter Tripod Tripod Leg Diameter Height Range of Mount Weight of Tripod Weight of EQ Head Weight of Counterweight Total Telescope Kit Weight

30 lb Dual Saddle Plate
NexStar+ hand control with LCD display, 19 fiber-optic backlit LED buttons
40,000+ objects, 100 user-defined programmable objects Enhanced information on over 200 objects Nine slew speeds, 4 deg/sec maximum EQ North, EQ South, Off Sidereal, Lunar, Solar 2-Star Align, Quick Align, 1-Star Align, Last Alignment, Solar System Align Low cog DC servo motors with encoders on both axes 12V DC 3 5A (tip positive) 7 degrees to 77 degrees Yes, Permanently Programmable Optional SkySync GPS Accessory Yes Yes 2x AUX ports, Autoguider port, RS-232 port (on hand control) No Optional 12″ 0 75″ Adjustable, Stainless Steel 2 0″ 44″ to 64″ 18 lb 17 lb 1x 12 lb 47 lb

30 I ENGLISH

Celestron Two Year Limited Warranty
A Celestron warrants your product to be free from defects in materials and workmanship for two years Celestron will repair or replace such product or part thereof which, upon inspection by Celestron, is found to be defective in materials or workmanship As a condition to the obligation of Celestron to repair or replace such product, the product must be returned to Celestron together with proof-of-purchase satisfactory to Celestron
B The Proper Return Authorization Number must be obtained from Celestron in advance of return Please submit your request to Celestron’s online technical support center at https://www celestron com/pages/technical-support to receive the number to be displayed on the outside of your shipping container
All returns must be accompanied by a written statement setting forth the name, address, and daytime telephone number of the owner, together with a brief description of any claimed defects Parts or product for which replacement is made shall become the property of Celestron
The customer shall be responsible for all costs of transportation and insurance, both to and from the factory of Celestron, and shall be required to prepay such costs
Celestron shall use reasonable efforts to repair or replace any product covered by this warranty within thirty days of receipt In the event repair or replacement shall require more than thirty days, Celestron shall notify the customer accordingly Celestron reserves the right to replace any product which has been discontinued from its product line with a new product of comparable value and function
This warranty shall be void and of no force of effect in the event a covered product has been modified in design or function, or subjected to abuse, misuse, mishandling or unauthorized repair Further, product malfunction or deterioration due to normal wear is not covered by this warranty
CELESTRON DISCLAIMS ANY WARRANTIES, EXPRESSED OR IMPLIED, WHETHER OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH HEREIN THE SOLE OBLIGATION OF CELESTRON UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR REPLACE THE COVERED PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN CELESTRON EXPRESSLY DISCLAIMS ANY LOST PROFITS, GENERAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT OF THE USE OR INABILITY TO USE ANY CELESTRON PRODUCT ANY WARRANTIES WHICH ARE IMPLIED AND WHICH CANNOT BE DISCLAIMED SHALL BE LIMITED IN DURATION TO A TERM OF TWO YEARS FROM THE DATE OF ORIGINAL RETAIL PURCHASE
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts, so the above limitations and exclusions may not apply to you
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state
Celestron reserves the right to modify or discontinue, without prior notice to you, any model or style product

If warranty problems arise or if you need assistance in using your product, please visit Celestron’s online technical support center at https://www celestron com/pages/technical-support
Note: This warranty is valid to U S A and Canadian customers who have purchased this product from an authorized Celestron dealer in the U S A or Canada Warranty outside the U S A and Canada is valid only to customers who purchased from a Celestron’s International Distributor or Authorized Celestron Dealer in the specific country Please contact them for any warranty service
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna
· Increase the separation between the equipment and receiver
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
· Consult the dealer or an experienced radio/TV technician for help
Product design and specifications are subject to change without prior notification
This product is designed and intended for use by those 14 years of age and older
©2021 Celestron · All rights reserved celestron com/pages/technical-support 2835 Columbia Street · Torrance, CA 90503 U S A Printed in China

ENGLISH I 31

GAMME

MODE D’EMPLOI POUR LES MODÈLES :

91519- Advanced VX Monture #32054- Advanced VX 6″ Télescope Newtonien #32062-

Advanced VX 8″ Télescope Newtonien #22020- Advanced VX 6″ Télescope Réfracteur

12025- Advanced VX 5″ Télescope de Schmidt-Cassegrain #12079- Advanced VX 6″

Télescope de Schmidt-Cassegrain

12026- Advanced VX 8″ Télescope de Schmidt-Cassegrain #12046- Advanced VX

9.25″ Télescope de Schmidt-Cassegrain #12067- Advanced VX 11″ Télescope de Schmidt-Cassegrain #12031- Advanced VX 8″ EdgeHD Télescope #12033- Advanced VX 9.25″ HD Télescope

TABLE DES MATIÈRES

Introduction

3

Monture Advanced VX

4

Assemblage

5

Bloc de commande électronique

10

Catalogue des objets

14

Pivoter vers un objet

14

Arbre du menu principal Advanced VX

21

Assemblage du tube optique

23

Installation du réfracteur

24

Installation du réflecteur Newtonien

24

Installation des tubes optiques EdgeHD & Schmidt-Cassegrain

25

Alignement du chercheur

27

Alignement polaire de la monture

27

Annexe A – Caractéristiques techniques de la monture Advanced VX

30

Garantie Limitée de 2 ans de Celestron

31

2 I FRANÇAIS

Introduction
Félicitations pour votre achat du télescope Celestron Advanced VX La monture équatoriale allemande Advanced VX a été conçue avec des matériaux de haute qualité afin de garantir sa stabilité et sa durabilité Tout cela pour que votre télescope vous procure du plaisir toute la vie avec un minimum d’entretien
En outre, la monture Advanced VX est polyvalente — elle évoluera avec vous pendant que votre intérêt se développe pour l’observation astronomique ou encore l’astro-imagerie
Si vous êtes un nouveau venu en astronomie, vous pouvez commencer par utiliser la fonction intégrée Sky Tour, laquelle contrôle le télescope afin de trouver les objets célestes les plus intéressants et le fait pivoter automatiquement vers chacun d’eux Si vous êtes un amateur expérimenté, vous apprécierez la vaste base de données contenant de plus de 40 000 objets, y compris des listes personnalisées de tous les meilleurs objets du ciel profond, des étoiles doubles si brillantes et des étoiles variables Peu importe votre niveau d’expérience, la série Advanced VX vous aidera, ainsi que vos amis, à découvrir les merveilles de l’univers
Parmi les caractéristiques du modèle Advanced VX, vous retrouverez :
· Moteurs à couple élevé contribuant à déplacer en douceur des charges plus lourdes
· Correction programmable permanente des erreurs périodiques (acronyme anglais PEC) pour un suivi amélioré
· Un port d’autoguidage dédié pour apporter des corrections lors de l’astro- imagerie
· Molettes d’alignements polaires grandes et faciles d’accès pour des mouvements rapides et sûrs
· Conception ergonomique permettant le désassemblage en pièces compactes et portables
· Limites de filtrage dans une base de données permettant la création de listes d’objets personnalisées
· Stockage des objets programmables et définis par l’utilisateur
· Nombreuses autres caractéristiques de haute performance!
La monture Advanced VX offre aux astronomes amateurs les télescopes les plus sophistiqués et faciles à utiliser qui sont actuellement offerts sur le marché
Prenez le temps de lire ce manuel avant d’entreprendre votre voyage dans l’univers Quelques séances d’observation peuvent être nécessaires afin de vous familiariser avec votre télescope, alors vous devriez conserver ce manuel à la portée de la main jusqu’à ce que vous maîtrisiez parfaitement le fonctionnement de votre télescope La commande manuelle contient des

instructions intégrées pour vous guider à travers toutes les procédures d’alignement nécessaires pour que le télescope soit opérationnel en quelques minutes Utilisez ce manuel en conjonction avec les instructions à l’écran fournies par la commande manuelle Le manuel donne des informations détaillées sur chaque étape ainsi que des documents de référence et des conseils pratiques qui rendront vos observations aussi simples et agréables que possible
Votre télescope est conçu pour vous donner des années d’observations amusantes et enrichissantes Cependant, il y a quelques points à considérer avant d’utiliser votre télescope afin d’assurer votre sécurité et la protection de votre équipement
Avertissement
· Ne regardez jamais directement le soleil à l’oeil nu ou avec un télescope (sauf si vous avez un filtre solaire adapté) Cela pourrait entraîner des lésions oculaires permanentes et irréversibles
· N’utilisez jamais votre télescope pour projeter une image du soleil sur une surface quelconque Une accumulation de chaleur interne pourrait endommager le télescope et tout accessoire qui s’y rattache
· N’utilisez jamais un filtre solaire oculaire ou un prisme (hélioscope) de Herschel Une accumulation de chaleur à l’intérieur du télescope peut endommager ces dispositifs, laissant alors la lumière non filtrée du soleil atteindre les yeux
· Ne laissez jamais le télescope sans surveillance Assurezvous qu’un adulte connaissant les bonnes procédures d’utilisation soit à côté de votre télescope en tout temps, surtout lorsque des enfants sont présents

FRANÇAIS I 3

Monture Advanced VX (Advanced VX avec tube optique 5″ Schmidt-Cassegrain représenté)
1

7

B

D

2 3
4

8 9
10

C E

5

F

11

A

6

1 Tube optique

2 Panneau de contrôle

3 Monture équatoriale Advanced VX

4 Échelle de réglage de latitude

5

Attache centrale des pieds du trépied / Support à accessoires

6 Trépied

7 Boîtier moteur dec

8 Contrepoids

9 R A (Ascension Droite) Boîtier moteur

10 Barre du contrepoids

11 Commande manuelle

PANNEAU DE CONTRÔLE A Port d’alimentation B Alimentation du moteur dec C Interrupteur marche/arrêt D Ports auxiliaires E Port de contrôle manuel F Pour du guide auto

4 I FRANÇAIS

Assemblage
Ce chapitre explique comment assembler votre télescope Advanced VX Votre monture devrait être livrée avec les éléments suivants :
· Tête équatoriale
· Trépied
· Support à accessoires
· Barre du contrepoids avec boulon de verrouillage
· Vis de réglage d’azimut (x2)
· Commande manuelle
· Support pour la commande manuelle (2 pièces)
· Câble du moteur de déclinaison
· Câble d’adaptateur pour batterie de voiture
· Contrepoids
Si vous avez fait l’achat de la monture Advanced VX séparément, alors un contrepoids devrait être également livré dans la boîte Si vous avez acheté la monture Advanced VX en tant que composant d’un kit, alors un ou deux contrepoids pourraient être livrés, selon le tube optique choisit Ces contrepoids seront livrés dans des boîtes séparées Vous trouverez plus d’informations dans la section du manuel dédiée à l’utilisation de votre tube optique
Retirez toutes les pièces de leurs sections internes et déposez-les sur une surface propre et plane Un grand espace sur le sol est idéal Pour installer votre monture Celestron, commencez par le trépied puis continuez ensuite Ces instructions sont données dans l’ordre où elles doivent être appliquées
Installation du Trépied
Le trépied Advanced VX est livré avec une Attache centrale des pieds du trépied / Support à accessoires métallique offrant un support solide comme le roc
Le trépied est livré assemblé avec une plaque métallique appelée tête de trépied, et qui tient les pieds attachées en haut De plus, il s’y trouve une barre centrale qui descend sous la tête du trépied et fixe la monture équatoriale à celui-ci Pour installer le trépied:
1 Retirez le trépied de la boîte et étirez les jambes du trépied, jusqu’à ce que chaque jambe soit complètement déployée Le trépied peut maintenant tenir debout de lui-même
2 Pour régler la hauteur des pieds, desserrez le levier situé au bas de chaque pied en le faisant tourner dans le sens des aiguilles d’une montre
3 Étendez chaque pied pour obtenir la longueur désirée puis fixez-la en faisant tourner les leviers dans le sens inverse des aiguilles d’une montre Veillez à bien serrer les pieds, pour éviter qu’elles ne glissent dans les tubes de nouveau par accident
Fixation des molettes de réglage d’azimut
Pour des raisons de sécurité de livraison, votre monture Advanced VX est livrée avec les molettes de réglage

d’azimut séparées Celles-ci devront donc être installées
Avant de fixer la monture au trépied :
1 Trouvez les molettes de réglage d’azimut dans la boîte contenant la tête équatoriale de l’Advanced VX
2 Vissez chaque molette dans chacun des trous situés de chaque côté de la monture
3 Ne vissez les molettes qu’à moitié, de manière à pouvoir insérer la cheville d’alignement du trépied, qui doit se glisser entre les deux extrémités des vis
Fixation de la monture équatoriale
La monture équatoriale de l’Advanced VX permet d’incliner l’axe de rotation du télescope de manière à ce que vous puissiez suivre le déplacement des étoiles dans le ciel La cheville d’alignement métallique se trouve sur l’un des côtés de la tête pour l’alignement de la monture Ce côté du trépied sera orienté vers le nord pour son installation pour observation astronomique Pour fixer la tête équatoriale :
1 Repérez les vis de réglage d’azimut sur la monture équatoriale
2 Dévissez les vis de réglage de manière à ce qu’elles ne rentrent plus dans le boîtier d’azimut de la monture Ne pas retirer les vis, car celles-ci seront nécessaires plus tard pour l’alignement polaire.
3 Tenez la monture équatoriale au dessus de la tête du trépied de manière à ce que le boîtier d’azimut se trouve au dessus de la cheville métallique
4 Déposez la monture équatoriale sur la tête du trépied de manière à ce que les deux soient encastrés
5 Poussez la molette située sur la barre centrale ellemême située sous la tête du trépied vers le haut et faites-la tourner dans le sens des aiguilles d’une montre pour fixer la monture équatoriale fermement

Tête du trépied

Monture Équatoriale
Molettes d’azimut (de chaque côté de
la monture)

Molette de monture

FRANÇAIS I 5

Votre trépied Advanced VX est livré avec la cheville d’alignement installée de manière à ce que l’axe polaire et la barre de contrepoids s’étendent entre les jambes du trépied Si désiré, vous pouvez repositionner la cheville du trépied de manière à ce que la barre de contrepoids se trouve directement au dessus d’une jambe du trépied Cela est une question de préférence et n’affecte pas la stabilité de la monture Les observateurs à plus basse altitude préféreront laisser la cheville d’alignement entre les deux jambes pour éviter que le contrepoids entre en contact avec les jambes du trépied lorsque celui-ci est en position la plus basse Pour modifier la vitesse des moteurs:

Molette de montage

Molette du support

Colonne centrale
Support à accessoires

Cheville d’alignement
Tête du trépied

Boulon de verrouillage

1 Utilisez une clef anglaise pour tenir la cheville en place et utilisez-en une autre pour dévisser le boulon de verrouillage situé sous la cheville d’alignement
2 Une fois le boulon desserré, la cheville peut être dévissée et déplacée sur le trou fileté situé à l’opposé sur la tête
3 Vissez la cheville au maximum, et repoussez-la jusqu’à ce que ses faces plates soient perpendiculaires au trépied
4 Utilisez une clef anglaise pour tenir la cheville en place et utilisez-en une autre pour visser le boulon de verrouillage sur la tête du trépied
5 Montez la tête équatoriale comme décrit ci-dessus
Fixation du support à accessoires
La monture Advanced VX est livrée avec un support pour accessoire équipé de trous spécialement conçus pour accueillir des oculaires de diamètres 3,1 cm et 5 cm Le support à accessoires est également une attache des jambes qui aide à stabiliser la monture Pour installer le support:
1 Retirez le boulon et la rondelle de la partie inférieure de la barre centrale
2 Faites glisser verticalement le support pour accessoires sur la barre centrale jusqu’à ce qu’il pousse sur l’intérieur de chacune des jambes du trépied
3 Vissez la molette du support pour accessoires dans la barre centrale et serrez

Installation de la barre de contrepoids Pour assurer l’équilibre du télescope, la monture est livrée avec une barre de contrepoids et au moins un contrepoids (selon le modèle) Installation de la barre du contrepoids:
1 Trouvez la barre de contrepoids et le boulon de verrouillage dans la boîte contenant la tête équatoriale Le boulon de verrouillage devrait déjà se trouvé à l’extrémité de la barre de contrepoids
2 Repérez l’ouverture de la monture équatoriale sur l’axe de déclinaison et vissez la barre de contrepoids dans l’ouverture jusqu’à ce qu’elle soit fermement installée
3 Vissez le boulon de la barre de contrepoids au maximum
Axe de déclinaison
Boulon de verrouillage
Barre de contrepoids
Contrepoids
Vis de sécurité Vis de verrouillage du contrepoids
Une fois la barre correctement installée, celle-ci est prête à recevoir le contrepoids
Astuce d’observation: Le télescope complètement monté peut peser lourd Positionnez la monture de manière à ce que l’axe solaire soit orienté vers le nord avant d’y installer le tube optique ou les contrepoids Cela simplifiera grandement la procédure d’alignement
Installation du contrepoids Pour installer le ou les contrepoids livrés avec votre monture ou kit de télescope:
1 Orientez la monture de manière à ce que la barre de contrepoids soit orientée vers le sol

6 I FRANÇAIS

2 Retirez la vis de sécurité du contrepoids situé à l’extrémité de la barre de contrepoids en la faisant tourner dans le sens inverse des aiguilles d’une montre La vis est présente pour empêcher le contrepoids de tomber de la monture au cas où la vis de verrouillage se déserre
3 Desserrez la vis de verrouillage du côté du contrepoids
4 Faites glisser le contrepoids sur la barre de contrepoids et faites-le glisser à environ la moitié de la hauteur de la barre
5 Serrez la vis de verrouillage sur le côté du contrepoids pour le fixer en place
6 Remettez la vis de sécurité en place
Astuce: Le trou au centre du contrepoids est légèrement plus grand sur un côté Lorsque vous glissez le contrepoids sur la barre, veillez à ce que le petit côté du trou soit orienté vers la tête équatoriale Cela permet de glisser le contrepoids au bas de la barre de contrepoids au cas où vous avez besoin d’affiner le réglage lorsque vous ajoutez des accessoires sur le tube optique Le petit côté du trou garantira que le contrepoids ne peut glisser complètement au dessus de la vis de sécurité
Fixer le support de commande manuelle
Les modèles de télescope Advanced VX sont livrés avec un support de commande manuelle qui se fixe à une jambe du trépied Le support de commande manuelle est livré en deux pièces : la pince de jambe, qui s’enclenche autour de la jambe du trépied et le support en soit qui se fixe sur la pince Fixation du support de commande manuelle:

l’installation du télescope Pour fixer le tube de télescope: 1 Desserrez les deux vis de fixation situées de chaque côté
de la plateforme de montage du télescope Cela vous permettra de glisser la barre à queue d’aronde dans la monture 2 Si votre télescope en comporte, retirez les vis de sécurité situées sous la barre à queue d’aronde 3 Faites glisser la barre à queue d’aronde du tube du télescope dans la plateforme de montage de la monture Faites glisser le télescope de manière à ce que la barre à queue d’aronde soit proche de la partie arrière de la plateforme de montage 4 Serrez les vis de verrouillage sur le côté la plateforme de montage pour le fixer en place Maintenant que le tube optique est fermement en place, les accessoires d’observation peuvent maintenant petre atatchés au télescope Cette étape est décrite en détails dans la section dédiée à l’utilisation des tubes optiques
Vis de sécurité
Barre de queue d’aronde
Vis de montage du télescope

1 Placez la pince de jambe contre une jambe du trépied et appuyez avec fermeté jusqu’à ce que celle-ci encercle la jambe
2 Faites glisser la partie arrière du support de mande manuelle vers le bas dans le guide situé sur le devant de la pince de jambe jusqu’à son enclenchement

Utiliser le double chevalet
Votre monture Advanced VX est livrée avec un double chevalet, qui vous permet d’utiliser n’importe quel tube optique utilisant une queue d’aronde sur plaque en V de 1,75″ (Synta, Vixen) ou du type de queue d’aronde de style D plus large de 3″ (75mm) (CGEM, CGX, CGX-L)

Support de la Commande Manuelle

Votre monture Advanced VX devrait déjà être configurée pour être utilisée avec une plaque en V de plus petite taille Pour convertir la monture afin de l’utiliser avec une plaque en D plus large, retirez simplement les deux boulons sur le côté gauche du chevalet de queue d’aronde à l’aide d’une clef Allen de 6mm

Pince de jambe

Fixation du tube optique à la monture
Le télescope se fixe à la monture à l’aide d’une barre coulissante à queue d’aronde située à la partie inférieure du tube du télescope Avant de fixer le tube optique, vérifiez que les molettes de déclinaison et d’ascension droite sont correctement serrées et que le ou les contrepoids sont installés en toute sécurité Cela est nécessaire pour garantir que la monture n’effectuera pas de mouvement incontrôlé pendant

Retirez les deux molettes et déplacez-les sur les deux trous filetés que vous venez de découvrir

FRANÇAIS I 7

4 Desserrez la vis située sur le côté du contrepoids, de manière à ce que celui-ci puisse être déplacé sur la barre
5 Déplacez le contrepoids jusqu’à ce qu’il équilibre le télescope (donc lorsque le télescope ne bouge plus lorsque les molettes de verrouillage R A sont desserrées)
6 Serrez la vis de verrouillage sur le côté du contrepoids pour le fixer en place

Pour garder les trous filetés propres, remettez toujours les vis Allen dans les trous d’installation que vous n’utilisez pas

Déplacement manuel du Télescope Pour effectuer un équilibrage correct de votre télescope, vous devrez orienter celui-ci manuellement vers différentes sections du ciel pour observer différents objets Pour effectuer les réglages grossiers, desserrez légèrement les leviers des molettes R A et DEC puis déplacez le télescope dans la direction désirée Chaque axe R A et DEC est équipé de leviers de verrouillage qui permettent de fixer chaque axe du télescope Pour desserrer les verrouillages du télescope, faites pivoter les leviers de verrouillage dans le sens inverse des aiguilles d’une montre
Levier de verrouillage de déclinaison

Astuce: Bien que la procédure décrite ci-dessus permette d’obtenir un équilibre parfait, un LÉGER déséquilibre doit être présent pour garantir un suivi aussi parfait que possible Lorsque le tube est du côté ouest de la monture, alors le contrepoids doit être légèrement déséquilibré du côté contrepoids Lorsque le tube est du côté est de la monture, alors un léger déséquilibre doit être présent du côté du télescope Cela est requis pour limiter l’effort de la vis sans fin Le déséquilibre doit être imperceptible Lorsque vous effectuez des prises de vues astronomiques, ce processus d’équilibrage peut être effectué pour l’affiner selon son orientation pour améliorer encore sa précision

Levier de verrouillage RA
Équilibrage de la monture en R.A. Pour limiter les tensions subies par la monture, le télescope doit être correctement équilibré autour de l’axe polaire Un équilibrage correct est crucial pour garantir un suivi précis Pour équilibrer la monture:
1 Vérifiez que le télescope est correctement fixé à la plateforme de montage du télescope
2 Desserrez le levier de verrouillage R A puis positionnez le télescope sur un côté de la monture La barre de contrepoids s’étendra horizontalement à l’opposé de la monture
3 Relâchez le télescope — GRADUELLEMENT — pour observer de quel côté il « roule »

Équilibrage de la monture en DEC
Bien que la monture ne puisse suivre en déclinaison, le télescope doit être également équilibré sur cet axe pour éviter les mouvements brusques lorsque le levier DEC est desserré Pour équilibrer le télescope en DEC:
1 Desserrez le levier de verrouillage R A et faites pivoter le télescope sur un côté de la monture (comme décrit dans la section précédente, « Équilibrage de la monture en R A »)
2 Resserrez le levier de verrouillage R A pour fixer le télescope en position
3 Desserrez le levier de verrouillage DEC et faites pivoter le télescope jusqu’à ce qu’il soit parallèle au sol
4 Relâchez le télescope — GRADUELLEMENT — pour observer de quel côté il pivote sur l’axe de déclinaison NE PAS RELÂCHER COMPLÈTEMENT LE TUBE!
5 Desserrez légèrement les molettes qui maintiennent la plateforme de montage et faites glisser le télescope vers l’avant ou l’arrière jusqu’à ce que celui- ci reste stable lorsque le levier DEC est desserré Ne PAS lâcher le télescope lorsque la molette de la plateforme de montage est desserrée Il pourrait être nécessaire de faire pivoter le télescope de manière à ce que la barre de

8 I FRANÇAIS

contrepoids soit orientée vers le bas avant de desserrer la vis de la plateforme de montage
6 Serrez les molettes sur la plateforme de montage pour le fixer en place
A l’instar de l’équilibrage R A , ce sont des instructions d’équilibrage générales et aideront à limiter la tension subie par la monture Lorsque vous effectuez des prises de vues astronomiques, ce processus d’équilibrage doit être effectué pour l’affiner selon son orientation
Régler la monture
Pour que le moteur puisse effectuer un suivi précis, l’axe de rotation du télescope doit être parallèle à l’axe de rotation de la terre, ce qui est appelé alignement polaire L’alignement polaire est obtenu NON PAS en déplaçant le télescope en R A ou DEC mais en réglant la monture verticalement, aussi appelé l’altitude et horizontalement, ou l’azimut Cette section explique les mouvements nécessaires pour effectuer l’alignement polaire du télescope Le processus réel d’alignement polaire, ou faire en sorte que l’axe de rotation du télescope soit parallèle à celui de la Terre, est décrit plus loin dans ce manuel, dans la section « Alignement polaire »
Réglage de la monture en altitude
· Pour augmenter l’altitude de l’axe polaire, serrez la vis arrière de réglage de latitude et desserrez la vis frontale
· Pour réduire l’altitude de l’axe polaire, serrez la vis frontale de réglage de latitude (qui se trouve sous la barre de contrepoids) et desserrez la vis arrière
Le réglage de la latitude sur la monture Advanced VX s’effectue sur une plage d’environ 7° à 77°

Réglage de la monture en azimut
Pour effectuer un réglage grossier de l’azimut, déplacez simplement l’ensemble du télescope Pour effectuer un réglage d’azimut fin:
Tournez les molettes de réglage situées de chaque côté du boitier d’azimut Lorsque vous-vous situez à l’arrière du télescope, ces molettes sont situées sur l’avant de la monture
· Tourner la molette de réglage de droite déplace la monture vers la droite
· Tourner la molette de réglage de gauche déplace la monture vers la gauche
Chaque vis déplace la cheville d’alignement de la tête du trépied, ce qui veut dire que vous pourriez avoir à desserrer une vis tout en en serrant une autre La vis qui fixe la monture équatoriale au trépied pourrait avoir à être légèrement desserrée
Gardez à l’esprit que le réglage de la monture est effectué pendant le processus d’alignement polaire seulement Une fois l’alignement polaire effectué, la monture ne doit PAS être déplacée Le pointage du télescope est effectué en déplaçant la monture en ascension droite et déclinaison, comme décrit ci-dessus dans ce manuel
Branchement du câble de déclinaison
L’Advanced VX est livré avec un câble permettant de brancher le panneau de contrôle électronique au moteur de déclinaison Pour brancher les câbles du moteur:
· Trouvez le câble de déclinaison et branchez-en une extrémité au port du panneau électronique portant le label Port DEC
· Insérez l’autre extrémité du câble dans le port du moteur de déclinaison

Molettes de réglage d’azimut

Molettes de réglage de latitude

Il est préférable d’effectuer les derniers réglages en altitude en déplaçant la monture contre la gravité (donc en utilisant la vis de réglage arrière pour lever la monture) Pour ce faire, vous devriez desserrer les deux vis de réglage de latitude et pousser l’avant de la monture autant que possible Serrez ensuite la vis de réglage arrière pour lever la monture à l’altitude désirée

Mise sous Tension du Télescope
L’Advanced VX peut être alimenté à l’aide de l’adaptateur pour batterie de voiture ou adaptateur optionnel CA 12 V N’utiliser que les adaptateurs fournis par Celestron L’utilisation d’adaptateurs d’autres marques pourrait endommager les composants électroniques et annuler la garantie du fabricant
1 Pour alimenter le télescope avec une batterie de voiture (ou adaptateur optionnel CA 12V), branchez simplement la prise ronde au port 12 V du panneau électronique et branchez l’autre extrémité à l’allume-cigare de votre voiture ou autre alimentation portative
2 Allumez le télescope en basculant l’interrupteur, situé sur le panneau électronique, en position « Marche »

FRANÇAIS I 9

Bloc de commande électronique
Vous venez de recevoir la nouvelle commande manuelle NexStar+ avec votre télescope La commande manuelle NexStar+ est maintenant pourvue d’un port USB vous permettant de la raccorder à un logiciel de contrôle sur PC, et d’effectuer les mises à jours de so

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>