Makita ML901 Rechargeable Flashlight Instruction Manual

Makita ML901 Rechargeable Flashlight

Symbols

The following shows the symbols used for the tool. Be sure that you understand their meaning before use.
Read the instruction manual.
Do not touch the bulb which is hot in use or immediately after outing our light.
You may get burnt.
Always recycle batteries.
Do not discard batteries into garbage cans or the like.

Explanation of general view

1. Set plate
2. Battery cartridge
3. Screw
4. Explanation of general view
5. Ring
6. Bulb holder
7. Reflector
8. Shoulder strap
9. Switch

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Note. Specifications may differ from country to country

IMPORTANT SAFETY INSTRUCTIONS

WARNING
When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:

READ ALL INSTRUCTIONS

1. Read this instruction manual and the charger instruction manual carefully before use.
2. This flashlight is not waterproof. Do not use it in damp locations. Do not expose it to rain or snow.
3. Do not wash it in water. A short circuit can cause a large current flow, overheating, possible burns, and even a breakdown.
4. Do not touch the inside of the flashlight head with tweezers, metal tools, etc. is traps the binary caring to name er get ate age yet as all co furious
5. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
6. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns, and even an explosion.
7. Be careful not to drop, shake, or strike the battery.
8. When the tool is not in use, always switch off and remove the battery cartridge from the tool.
9. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
10. Do not give the tool a shock by dropping, striking, etc.
11. Do not expose the light to the eyes continuously. It may hurt them.
12. Do not cover or clog the lit tool with cloth or carton, etc. It may create a risk of fire.
13. Switch off the light immediately when the lamp gets dark in use. If you leave the lamp switched on, the battery cartridge capacity may decrease.
14. Do not disassemble the charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
15. If any problem develops, consult your nearest Makita Service Center or dealer. To maintain product safety and reliability, repairs, maintenance, or adjustments should be carried out by Makita Authorized Service
    Center.

OPERATING INSTRUCTIONS

Charging
For ML702 (Fig. 1), ML902 (Fig. 1), and ML901 (Fig. 2) Charge the battery cartridge with the Makita charger before use. To remove the battery cartridge, pull out the set plate on the torch/flashlight and grasp both sides of the cartridge while withdrawing it from the torch/flashlight. After charging, insert the battery cartridge into the torch/flashlight, and snap the set plate back into place.

For ML903 (Fig. 3)
Charge the battery cartridge with the Makita charger before use. To remove the battery cartridge, withdraw it from the torch/flashlight while pressing the buttons on both sides of the cartridge. After charging, insert the battery cartridge into the torch/flashlight until it locks in place with a little click.

NOTE
Battery cartridges 9100, 9102, 9100A, and 9102A can be used on ML903 if you install the set plate. Install the set plate on ML903 with the screw provided as shown in Fig. 4 The following tables indicate the charging time and operating time on a single charge.

ML702

ML901/ML903

(Note)
if you use a power-checking battery on Model ML901/ML903, the power-checking battery will not indicate the remaining battery capacity properly

ML902

Storing battery cartridge

Always charge the Nickel Metal Hydride battery cartridge before storing it when you have not used it for more than six months.

Head angle (Fig. 5)
The head angle can be adjusted in four stages. Adjust as desired.

Replacing bulb (Fig. 6 & 7)

CAUTION
The bulb is very hot immediately after operation. Wait until the bulb cools off before attempting to replace it. First, turn the ring counterclockwise and remove the reflector. Remove the bulb holder by turning it counter-
clockwise. Then replace the bulb. Shoulder strap (Fig. 8) Install the strap on the tool.

MAINTENANCE

To maintain product safety and reliability, repairs, Maine- nance, or adjustments should be carried out by a Makita Authorized Service Center.

ACCESSORIES

CAUTION
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or
attachments should be used only in the proper and intended manner.

• Bulb set (2 pcs)
• Shoulder strap
• Set plate (For Model ML903)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>