YZEENM 52 Inch Ceiling Fan with LED Light and Remote Owner’s Manual
- June 15, 2024
- YZEENM
Table of Contents
YZEENM 52 Inch Ceiling Fan with LED Light and Remote
WARNING: To avoid fire, shock and serious personal injury, please read the following instructions carefully.
Important Safety Instructions
- Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
- Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.
- Make sure all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it -yourself wiring handbook if you are unfamiliar with installing electrical wiring
- Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blades.
- If you are mounting the fan on a ceiling outlet box, use a metal outlet box. Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan ( at least 50 lbs.). Do not use a plastic outlet box. Attach the mounting bracket by using the hardware supplied with the ceiling outlet box.
- If you are mounting the fan to a joist, make sure it is strong enough to support the moving weight of the fan (at least 50 lbs.)
- After installing the fan, make sure all the connections are secured. This will prevent the fan from falling
- Do not insert anything into the fan blades while the fan is operating.
- Turn the fan off and wait for it to stop before reversing fan direction.
- To reduce risk of electrical shock and personal injury, do not install the fan on a sloped ceiling.
- To reduce the risk of electrical shock and personal injury, do not use this fan with any solid-state.
- To reduce risk of personal injury, use only the two steel screws and lock washers provided with the fan for mounting the outlet box.
ASSEMBLY DRAWING & PARTS LIST LIGHT
Unpacking Your Fan
To pause the chand of a the or postel damages, please move tre insalation. required for installation.
HOW TO INSTALL THE FAN WITH LIGHT
-
Install the hanger
NOTE: Do not install a hanger on the roof leaking and damp, the hanger
After the installation must be able to withstand a weight of 40 kg or more, in order to prevent smallpox Drop off the top of the danger. -
when the case of concrete ceiling, use a drill hole drilled in the ceiing of two $ 8( distance between the two holes should be appropriate), he expansion screw into the hole, then put the hanger expansion screw set into the tum flat washers and nuts and tighten with a spanner wrench (Fig. 1 )
-
The ceiling is made of wood, please lock with a screwdriver hanger on the ceiling (Figure 1. 1) Parts bag flat was her set into the wood screws.
NOTE: Do not install on a hanger uneven ceiling, and ceiling-mounted hanger must decide firmly not be loose. -
Install the host
-
Install the fan blades +onto the motor
-
When installing the fan blades, the gasket should be installed
-
Remove the three light panel screws
-
Fix the lamp panel with the removed screws
-
Connect the LED to the host cable
-
Finally, clip the lampshade onto the lamp panel
-
Loosen two set screws on the download support and then place the download into the download support. (Figure 3). There ad the electrical wires and the earth wire through the download. Align the Clevis Pin holes in the Downrod with the holes in the Downrod Support. Be sure to push the straight leg of the Hairpin through the hole near the end of the Clevis Pin until the curved portion of the Hairpin snaps around the Clevis Pin. Finally, re-tighten the two set screws.
-
4. Carefully lift the fan, and set the downrod / hanger ball assembly on the hanger bracket attached to the ceiling joist. Be sure the groove in the ball is properly aligned with the tab on the hanger bracket. (Figure 4)
WARNING
The fan must be hung with at least 230 cm of clearance from floor to blades.
Once the wiring step has been completed, slide the wired remote receiver in
between the mounting bracket and the top of the download ball.
INSTALLATION STEPS OF MODERN MODELS
Frequency conversion remote control wiring method
SCHEMATIC DIAGRAM OF REMOTE CONTROL WIRING
WARNING
Turn off the main power before installation The wiring mode is one live line and one neutral line
Installation requirements
- It can be installed with ordinary wiring, and it can also be installed with old house reconstruction without wiring, which is suitable for installation without multi-wiring.
ANNOUNCEMENTS
Connect the wiring strictly according to the requirements shown in the remote control wiring diagram, and never connect the wiring incorrectly or mix colors, otherwise it will not work normally, and the circuit board will be severely short-circuited and burned.
IMPORTANT: PAIRING BETWEEN REMOTE AND RECEIVER
Turn “ON” the power supply and within 30 seconds Immediately quickly press the “SETUP “button on the remote control 5 times, and the light flashes successfully to match the code successfully pairing and all functions will work normally.
IMPORTANT:
pairing initial step must be performed within 30 seconds of power being turned on.
- (a) when pairing multiple fans please ensure the isolation switch or power supply to the first installed fan is turned off prior to pairing futher fans e. please pair one fan at a time
- (b). please ensure the isolation switch is kept to the ON position, the isolation switch is not to be used as a light switch as this will damage and make the remote receiver inoperable
- If the transmitter functions are not working please check the battery orientation and power level. Low battery voltage will affect the functions of your transmitter and the operation of your fan. Other remote controls nearby using the same frequency may cause interference with the fan’s receiver.
- Please remove batteries from the transmitter if left unused for an extended period of
time.
IMPORTANT REMINDERS
- Please note: The receiver must be correctly installed in the mounting bracket on the fan
- When the transmitter cannot control the receiver, please check the battery has sufficient charge in the transmitter.
- When the transmitter cannot control the receiver, please check if there is any existence of similar remote-controlled products nearby, causing interference with each other.
- Low power of the battery will affect the sensitivity of the transmitter and the signal reception accordingly, must be replaced if the battery is getting low power.
- Please take the battery out from the transmitter when left unused for a long time, to avoid battery leaks.
- Isolation Switch “Must be connected in the line.”
- When power is cut to the unit (via a blackout or otherwise) when power is restored the light will come on.
MAINTENANCE
- Periodic cleaning of your new ceiling fan is the only maintenance that is needed.
- When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish.
- Abrasive cleaning agents are not required and should be avoided to prevent damage to finish.
RECOMMENDED:
Periodically check that the blade sets to the fan motor setscrews are secure and tight.
WARNING
Do not use solvents when cleaning your ceiling fan. It could damage the motor and create the possibility of electrical shock.
Remote Control Manual
- The way to set up: Turn off the power switch or wall switch, Within 3 seconds after power on, press the setup button three times in succession, the light flashes to indicate successful setup.
- Clear match: Turn off the power switch or wall switch, press and hold the “SETUP” button and do not let it go, then turn on the power switch or wall switch, and let it go after hearing the beep, unset up is successful.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>