BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater Instruction Manual

June 14, 2024
BIG ASS FANS

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater Instruction Manual

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater Instruction
Manual

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater -
warning

READ AND SAVE THESE INSTRUCTIONS

Please read this owner’s manual carefully before using the unit and keep this manual for future reference.
USE THIS HEATER ONLY AS DESCRIBED IN THIS MANUAL. ANY OTHER USE NOT RECOMMENDED BY THE MANUFACTURER MAY CAUSE FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS.

Notice : Changes or modifications not approved by the party responsible for compliance will void the user’s
authority to operate the equipment.

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following outlined in section 1 – SAFETY. Read all instructions before installing or using this heater. This heater must be used strictly according to these instructions.

SAFETY

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - warning
2

WARNING: FIRE OR EXPLOSTION HAZARD

  • Failure to precisely follow safety warnings could result in serious injury or property damage.
  • This heater has hot surfaces and arcing or sparking parts inside. Do not use the heater in areas where gasoline, paint or flammable vapors or liquids are used or stored.
  • This heater is not to be installed or used in an area containing hazardous or flammable materials including but not limited to rags, fabrics, spray or aerosol cans, cleaning compounds, plastic containers, paper products, organic dusts, straw/hay, gasoline, kerosene, lighter fluid, etc.
  • To prevent a possible fire, do not block air intakes or exhaust in any manner.
  • Do not allow combustible materials contact the heater due to wind or other environmental factors.
  • Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage to the heater.
  • Do not cover the heater in any manner, do not hang clothing on or near the heater.
  • Caution! Do not use the heater together with another appliance connected to the same supply line or connected to the same breaker.
  • This heater must be properly grounded.
  • The power cord must not be left on or around the heater body.
  • Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, curtains, etc. at least 6 feet (1.8m) from the front of the heater and keep them away from the sides and rear.

WARNING: PERSONAL INJURY HAZARD – OPERATION

  • Caution! Risk of scald injury! This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

  • Never leave the heater unattended while it is operating.

  • Do not use the heater without the aluminium grille in place.

  • Do not operate any heater after it malfunctions.
    Disconnect power at service panel and have heater inspected by an electrician before reusing.

  • Do not use the heater to light cigarettes or similar materials.

  • Do not insert objects in heater openings. Electrical shock could result.

  • To disconnect heater, turn controls to off, and turn off power to the heater circuit at the main disconnect panel.

WARNING: PERSONAL INJURY HAZARD – CLEANING AND MAINTENANCE

  • To avoid property damage, personal injury or death due to electrical shock DO NOT service the unit without turning the unit OFF and disconnecting the heater from the main power supply.
  • Before cleaning the unit or replacing the emitter, turn off the main power. Make sure the heater and/or the emitter is cool before handling.
  • Service must be performed only by a qualified service technician.

WARNING: INSTALLATION

  • This product must be installed by a certified electrician and must adhere to all local, state and national electric codes (NEC).

  • This product is not suitable for indoor residential use. (Indoor commercial installation is acceptable)

  • Check if the voltage indicated on the nameplate of the appliance corresponds to the local mains voltage before connecting the appliance.

  • Remove all packaging materials, including emitter anti vibration inserts prior to using the heater.

  • Do not direct the radiant part of the heater towards the ceiling.

  • Specified minimum clearances from front, sides, bottom and back of unit must be met.
    Failure to meet clearance minimums can result in fire.

  • Heater is not for use in bathrooms, laundry areas or other locations where unit could fall into water.

  • Do not use the heater if it has been dropped or damaged in any way. Ensure the emitter is not cracked or chipped visually. Contact an authorized BIG ASS FANS dealer for support.

  • Do not install this product directly below a receptacle or wall socket outlet.

  • Do not use the heater if the power cord is damaged. Contact an authorized servicer or qualified electrician to replace the cord prior to use.

  • Unplug the appliance when it is not in use for long periods of time, or for cleaning and maintenance.

  • Heater is not to be recessed!

  • The heater must be installed at level on a flat, stable surface, rigid enough to safely withstand the weight of the heater and the heater must not be covered by any flexible material, such as carpets, plastic or fabric.

INSTALLATION INSTRUCTIONS

Heater installation must be carried out by qualified personnel in compliance with local National Codes (NEC) as well as any other applicable standards. Failure to comply with applicable requirements could result in personal injury and/or property damage. Wiring procedures and connections shall be made in accordance with national and local electrical codes having jurisdiction.

BIG ASS FANS infrared heaters produce radiant heat that warms people and objects, rather than the air around them. The heater can be wall or ceiling mounted and includes brackets which allow the user to direct the infrared heat where desired.

To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater.

2.1 INSTALLATION CLEARANCE DISTANCES

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - DANGER FIRE
HAZARD

The minimum clearances indicated on the nameplate and in the user manual must be observed.
CAUTION: High temperatures are present, risk of fire! Keep electrical cords, drapery, furnishings and other combustibles at least 6 feet (1.8m) from the front of the heater and away from the sides and rear.

Minimum Clearance Distances

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - Minimum
Clearance Distances

Wall Mount Minimum Clearances

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - Wall Mount
Minimum Clearances

Ceiling Suspended Minimum Clearances

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - Ceiling
Suspended Minimum Clearances

2.2 ELECTRICAL INSTALLATION

Safety Precautions

  1. Each power supply circuit must be properly grounded.
  2. Use a certified ground fault protection device for wet environment installations.
  3. Use a proper electrical connection box.
  4. Supply voltage and frequency must correspond to the electrical rating indicated on unit’s information
    plate.

2.3 WALL-MOUNTED INSTALLATION

THE BAFCF60240 HEATERS MUST BE INSTALLED WITH THE MOUNTING BRACKETS PROVIDED IN THE BOX.

  1. Take the heater out of the box and remove all protective foam inserts and packaging.

  2. Select the installation location on the wall by identifying the studs or structural beams that will allow the heater to be securely attached.
    WARNING: Ensure minimum clearances outlined in section 2.1 are met.

  3. Securely fasten the L-shaped brackets to the mounting surface using both fixing holes in the short part of the bracket. Brackets should be attached as shown below. NOTE : Wall bolts or anchors are not supplied. Select an appropriate size to provide adequate support for the weight of the unit and taking into consideration any wind load conditions.
    CAUTION: If there is any question regarding security of the bolts and fixtures, contact a professional contractor.

  4. Mount the heater to the brackets with the terminal box at the right side of the heater.

  5. Adjust the heater to the desired directional angle, then fix in this position by tightening the fixing bolts on the brackets at the back of the heater.

  6. Secure the electrical supply cable so it does not contact the heater body or obstruct the air vents.
    Follow local and national electrical code requirements.
    BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - Follow local and
national electrical code
    The angles of attachment are 20° to 70°, measured from the mounting wall.

2.4 CEILING MOUNTED INSTALLATION

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - warning
3

  1. Assemble the ceiling mounting hardware as shown in the guide below. The socket head cap screw should be used on the ceiling bracket side, and the hexagon head cap screw should be used on the heater bracket side for clearance purposes. See Illustration.
    BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - Assemble the
ceiling mounting hardware

  2. Secure the heater to the mounting brackets using nuts and washers provided.

  3. Select the installation location on the ceiling by identifying the studs or structural beams that will allow the heater to be securely attached.
    NOTE : ceiling bolts or anchors are not supplied.
    Select an appropriate size to provide adequate support for the weight of the unit (22lbs / 10 Kg) and take into consideration any wind load conditions.

  4. Attach the unit to the ceiling using the ceiling brackets and user selected bolts. An illustration of the bolt pattern dimensions is shown to the right.

  5. The heater can be hung vertically or pointed at a maximum angle of 45° from vertical.
    NOTICE: NEVER direct the infrared heat produced by the appliance at an adjacent wall.

  6. Secure the electrical supply cable so it does not contact with the heater body or cover the heater air vents.

2.5 ADJUSTING DIRECTIONAL POSITIONING

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - warning
4

  1. Turn off the heaters electrical supply line from the main power supply.
  2. Allow the heater to cool before adjusting the angle.
  3. Loosen the fixing bolts on the brackets at the back of the heater; adjust the heater as desired, then re- tighten the fixing bolts.

Notice : The unit produces radiant heat that warms people and objects rather than the air around them. Install the heater at an angle which points the reflector at the target space. Do not point the heater at windows or vacant spaces, as the heat will not be delivered to the occupants.

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - INCORRECT,
CORRECT

OPERATING INSTRUCTIONS

Caution! The heater must be properly installed before it is used.

3.1 REMOTE CONTROL
The remote control must be pointed in the direction of the receiver on the heater junction box. (located on the right side of the heater). The remote must be in line of sight of the domed receiver when the user intends to adjust the power level. The remote must be used within a maximum distance of 6 m.

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - REMOTE
CONTROL

In remote mode the heater has the option to run at 50% or 100% power. Each emitter is controlled separately
using the up and down arrows on the remote. Pressing the up button (˄) will turn the upper emitter on. Pressing up again will turn the upper emitter off. Pressing the down button (˅) will turn the lower emitter on. Pressing down again will turn the lower emitter off. Pressing the (all) button will turn both emitters on, pressing it again will turn both emitters off.

3.1.1 OPERATION OF THE REMOTE CONTROL

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - OPERATION OF THE
REMOTE CONTROL

Notice:

  1. Use 2 pieces AAA, 1.5V batteries (not included) in the remote control. Remove the batteries when not in use for an extended period of time to increase battery life.
  2. Contact your local authorized BIG ASS FANS Dealer for remote replacement.
  3. The remote-control function may not work if there is a barrier between the remote control and heater.
  4. Replace the batteries as required to ensure correct remote functionality.

MAINTENANCE

BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - warning
5

  1. Allow the heater and the emitter to cool down before handling.
  2. Installation and maintenance must be performed by a qualified technician.
  3. Turn off the power before beginning maintenance.
  4. Do not attempt to service or repair the unit while it is running.
  5. Should the heater be dropped or damaged or malfunction at any time, immediately turn off the main power source and do not use it until it has been examined by an authorized service facility.

Notice: Do not touch the emitter with bare hands. Wearing soft cotton gloves is highly recommended. Finger
prints will burn into the carbon emitter during use and cause premature heater failure. If the emitter is anidvertently touched, or if it needs to be cleaned, carefully wipe it using rubbing alcohol or methylated spirits.

4.1 CLEANING

To keep the heater running at peak performance and prevent premature failure, the emitter lamp and reflector should be cleaned as required. Buildup of dust on these components will accelerate aging. In seaside environments, salt spray may collect on these components. Salt spray should be removed regularly.

To clean the reflector or emitter lamp, follow these steps:

  1. Turn the power to «OFF» and disconnect the heater from the main power supply.
  2. Remove screws from the left side cover and slide the perforated front grille out of the heater body.
  3. Carefully wipe the reflector with a soft, lint-free cloth. Do not use abrasive cleaners or abrasive scrubbing brushes for cleaning!
  4. After cleaning, be sure to properly reinstall the heater grille.

4.2 REPLACING THE EMITTER

Contact your distributor for the correct replacement emitter, providing the model number and rating from the rating label. Using an incorrect replacement emitter can cause the heater to fail.

Notice : Read through the Emitter replacement procedure below before beginning the replacement. For easier replacement, remove the heater from the wall or ceiling.

  1. WARNING! TURN OFF THE POWER AND DISCONNECT THE HEATER FROM THE MAIN POWER SUPPLY. FAILURE TO DISCONNECT HEATER BEFORE REPLACING THE EMITTER COULD CAUSE ELECTRIC SHOCK OR DEATH!

  2. Turn OFF the power and disconnect from main power supply.

  3. Be sure the heater and the emitter are cool: burns can result from touching hot components.

  4. Remove screws from the left side of the heater fixture and remove the aluminum end cap. (keep these parts).
    BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - Remove screws
from the left side of the heater

  5. Carefully slide the protective grille out of the heater body to expose the emitter and the white sealing connectors.

  6. Carefully unscrew the protective white cap and carefully slide the cap back cap to expose the wire/ metal connector system.
    Caution! Disconnect the metal locking connectors by squeezing the metal tab.

  7. Bend the metal tabs to remove the small reflector shield sheet metal parts. Hold on to these pieces. This will allow you to slide the emitter into a bigger cavity to remove it from the reflector and heater body. Properly dispose of the broken emitter at your local recycling center.
    BIG ASS FANS BAFCF60240B Obsidian Electric Outdoor Heater - Bend the metal
tabs to remove the small

  8. Hold the new emitter by the ceramic ends or wear clean dry gloves to prevent and position the new lamp inside the unit.

  9. Insert the new emitter through the reflector openings. Insert the Reflector Shields and bend the tabs back into place. The Reflector Shields hold the emitter in the correct position during operation. It is important that they are re- installed during emitter replacement.

  10. Connect the new emitter to the terminals of the heater; screw in the white plastic caps

  11. Carefully replace the protective aluminum grille and screw the protective end cap in place.

Due to ongoing product improvements, specifications and dimensions are subject to change and correction without notice and without incurring obligations. Determining the application and suitability for use of any product is the responsibility of the installer. Additionally, the installer is responsible for verifying dimensional data on the actual product prior to beginning any installation preparations.

Incentive and rebate programs have precise requirements as to product performance and certification. All products meet applicable regulations in effect on date of manufacture; however, certifications are not necessarily granted for the life of a product. Therefore, it is the responsibility of the applicant to determine whether a specific model qualifies for these incentive/rebate programs.

Manual Revision: A: 2023-10-18

BIG ASS FANS logo

Qr code icon

BIGASSFANS.COM/PRODUCT-WARRANTIES

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

BIG ASS FANS User Manuals

Related Manuals