DEAF BONCE MM-50L Series Mid Range Speaker Owner’s Manual
- June 14, 2024
- Deaf Bonce
Table of Contents
- DEAF BONCE MM-50L Series Mid-Range Speaker
- Product Information
- Product Usage Instructions
- INTRODUCTION
- SAFETY INSTRUCTIONS
- WIRING DIAGRAMS
- Serial connection of the speakers
- FILTERING, RECOMMENDED AMPLIFIER SETTINGS
- SPECIFICATIONS
- DIMENSIONS
- Connection of terminals
- Installation
- BOX CONTENTS
- WARRANTY PERIOD, AFTER-SALES SERVICE AND SERVICE LIFE INFORMATION
- Documents / Resources
DEAF BONCE MM-50L Series Mid-Range Speaker
Product Information
Specifications
- Model: MM-50L / MM-60L / MM-80L
- Size (Inch):
- Surround material:
- Cone material:
- Frame material:
- Magnet type:
- Power RMS (W):
- Power MAX (W):
- Voice coil size (Inch):
- Voice coil wire:
- Frequency response (Hz):
Product Usage Instructions
Introduction
Thank you for purchasing this Deaf Bonce product! Our company is committed to
the creation of extremely loud sound systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using
this product. You must read and observe caution in this manual. Please keep
the manual in a safe and accessible place for future reference.
Safety Instructions
-
Fasten the speakers properly when installing them in the vehicle.
If the component is disconnected during driving, it may cause serious damage to the passengers of the vehicle or another vehicle. -
Before installing the components, if possible store the product in its original package to avoid accidental damage to the product.
-
CAUTION!!! High sound pressure can damage your health! Please use common sense when controlling the volume!
Wiring Diagrams
- Do not expose your amplifier to loads below the value predetermined by the manufacturer. Various examples of connection types are given below. Use these examples to determine the required load impedance of your connection.
Serial connection of the speakers
- Voice coil 4 Ohm – 2 MR
Total impedance: 8 Ohm
Parallel connection of the speakers
- Voice coil 4 Ohm – 2 MR
Total impedance: 2 Ohm
The mixed connection between the speakers
- Voice coil 4 Ohm – 4 MR
Total impedance: 4 Ohm
Filtering, Recommended Amplifier Settings
- The recommended filter settings
- The high pass filter HPF (the filter that cuts all frequencies below those set for the filter) should be set to 150-250 Hz (24 dB/Oct), or 250-350 Hz (12 dB/Oct)
- The low pass filter LPF (the filter that cuts all frequencies above those set for the filter) should be set to 8-10 kHz (12 dB/Oct)
- Recommended amplifiers: MLA-60.2, MLA-100.2, MLA-160.2, MLA-60.4, MLA-100.4, MLA-160.4.
Specifications
- Please refer to the specifications section above for detailed information about the product’s specifications.
FAQ
Q: How do I select the diameter of speaker cables?
- A: Use the table below to select the desired diameter based on the length and the power consumption.
Power consumption (W) | Cable length (m) | Size |
---|---|---|
25,000 | 5 | 16.8 |
20,000 | 8 | 8.37 |
15,000 | 10 | 5.26 |
10,000 | 14 | 2.08 |
8,000 | 4 | – |
6,000 | – | 1-2 |
4,000 | – | 2-3 |
2,000 | – | 3-4 |
1,000 | – | 4-5 |
500 | – | 5-6 |
250 | – | 6-7 |
100 | – | 7-8 |
INTRODUCTION
- Thank you for purchasing this Deaf Bonce product! Our company is committed to the creation of extremely loud sound systems with no loss of quality.
- To ensure proper use, please carefully read through this manual before using this product. You must read and observe caution in this manual.
- Please keep the manual in a safe and accessible place for future reference.
SAFETY INSTRUCTIONS
- Fasten the speakers properly when installing them in the vehicle. If the component is disconnected during driving, it may cause serious damage to the passengers of the vehicle or another vehicle.
- Before installing the components, if possible store the product in its original package to avoid accidental damage to the product.
- Be careful when installing or dismantling the speaker! Do not let the speaker drop to avoid damage to its moving parts.
- When working with tools follow safety rules.
- Before the installation switch off the head unit and all other audio devices to avoid their damage.
- Make sure that the location of the speaker does not hinder the proper operation of the mechanical and electrical devices of the vehicle.
- Do not install components in places exposed to water, excessive humidity, high or low temperature, dust, or dirt.
- ATTENTION!!! The product may be operated at +5 °C (41F) to +40 °C (104F). In case of moisture condensation, let the product dry.
- When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe, or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
- When stretching back the speaker cables make sure that they are not in contact with sharp edges or moving mechanical devices. Make sure that they are firmly fixed and protected over the entire length.
- The diameter of the speaker cables must be selected under the length and applied power.
- Never stretch the cables outside of the car and near the moving parts of the car. This can lead to the destruction of the insulating layer, short circuit, and fire.
- To protect the cables use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the parts exposed to heat.
CAUTION!!! High sound pressure can damage your health! Please use common sense when controlling the volume!
WIRING DIAGRAMS
- Do not expose your amplifier to loads below the value predetermined by the manufacturer.
- Various examples of connection types are given at the pages below. Use these examples to determine the required load impedance of your connection.
Serial connection of the speakers
Voice coil | Total impedance |
---|---|
4 Ohm х 2 MR | 8 Ohm |
Voice coil | Total impedance |
---|---|
4 Ohm х 3 MR | 12 Ohm |
Voice coil | Total impedance |
--- | --- |
4 Ohm х 4 MR | 16 Ohm |
Parallel connection of the speakers
Voice coil | Total impedance |
---|---|
4 Ohm х 2 MR | 2 Ohm |
Voice coil | Total impedance |
--- | --- |
4 Ohm х 3 MR | 1.33 Ohm |
Voice coil | Total impedance |
--- | --- |
4 Ohm х 4 MR | 1 Ohm |
The mixed connection between the speakers
Voice coil | Total impedance |
---|---|
4 Ohm х 4 MR | 4 Ohm |
CAUTION!!! High sound pressure can damage your health! Please use common sense when controlling the volume!
Selection of the diameter of speaker cables
Use the table below to select the desired diameter based on the length and the power consumption.
FILTERING, RECOMMENDED AMPLIFIER SETTINGS
- The correct choice of amplifier, its settings, filtering, and enclosure largely influence the lifespan of your audio system. You should select an amplifier with a nominal power, not exceeding the nominal power of the speakers.
- Proper coordination of the head unit (HU) with the amplifier will allow clean, undistorted signals applied to the component to prevent overheating and voice coil damage.
- Recommended settings of the amplifier and HU: HU volume should not exceed 80%. The amplifier sensitivity should be set to 50%.
The recommended filter settings:
- The high pass filter HPF (the filter that cuts all frequencies below those set for the filter) should be set to 150-250 Hz (24 dB/Oct), or 250-350 Hz (12 dB/Oct)
- The low pass filter LPF (the filter that cuts all frequencies above those set for the filter) should be set to 8-10 kHz (12 dB/Oct)
- Recommended amplifiers: MLA-60.2, MLA-100.2, MLA-160.2, MLA-60.4, MLA-100.4, MLA-160.4.
SPECIFICATIONS
Model | MM- 50L | MM- 60L | MM- 80L |
---|---|---|---|
Size (Inch) | 5.2 | 6.5 | 8 |
Surround material | Cloth | Cloth | Cloth |
Cone material | Pressed paper | Pressed paper | Pressed paper |
Frame material | Stamped Steel | Stamped Steel | **Stamped |
Steel
Magnet type| Ferrite| Ferrite| Ferrite
Power RMS (W)| 80| 80| 100
Power MAX (W)| 160| 160| 200
Voice coil size (Inch)| 1| 1| 1
Voice coil wire| CCAW| CCAW| CCAW
Frequency| 120 – 16 000| 100 – 12 500| 80 – 11 000
THIELE- SMALL| PARAMETERS| |
Impedance (Ohm)| 4| 4| 4
Spl (dB)| 91.6| 91.5| 93.8
Fs (Hz)| 116| 102| 77.4
Vas (L)| 3.45| 9| 25.87
Qts| 0.71| 0.93| 0.68
BL| 4.39| 4.06| 5.28**
This specified sensitivity is not directly connected with the sound pressure in the vehicle, and therefore should not be used as the sole indicator for comparison with other speakers.
DIMENSIONS
- MM -50L
- MM- 60L
- MM- 80L
Connection of terminals
Installation
BOX CONTENTS
- Mid-range speaker – 2 pcs.
- Owner`s manual – 1 pc.
- Warranty card – 1 pc.
WARRANTY PERIOD, AFTER-SALES SERVICE AND SERVICE LIFE INFORMATION
- Each Deaf Bonce product is warranted to be free from defects in materials and workmanship under normal use and service.
- The warranty period for the product is 12 (twelve) months from the date on which the product is transferred to the consumer (this date shall be deemed to be the date on which the consumer starts using the product).
- During the warranty period, defective parts will be repaired or replaced at the discretion of the manufacturer provided that there are grounds for doing so under the laws of the consumer’s country. The defective product must be returned to the dealer from whom it was purchased together with the duly filled out warranty certificate, complete, with original packaging.
- Our company shall not be liable for any damage caused by transportation. Our company shall not be liable for any expenses or lost profits arising out of or in connection with the use or inability to use the product or any other incidental or indirect costs, expenses, or damages incurred by the customer. The warranty is valid under the laws currently in force. For more information, please visit our company website and refer to the warranty card.
- The manufacturer reserves the right to change the design and specification of the product without prior notice.
- The service life of the product is 12 (twelve) months from the date on which the product is transferred to the consumer (this date shall be deemed to be the date on which the consumer starts using the product).
- The product or any part (component) of the product must not be used in any way (including, but not limited to use for intended or any other purpose, transportation, storage, modification/alteration/improvement/upgrade) after the expiry of the service life.
- At the end of its service life, the product must be disposed of.
INFORMATION ON DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT (FOR THE EUROPEAN COUNTRIES WITH SEPARATE WASTE COLLECTION)
- Items marked “crisscrossed wheeled bin” are not allowed to be disposed of together with usual household waste. These electrical and electronic products should be disposed of in special reception centers, equipped for recycling such products and components.
- For information about the location of the nearest disposal/recycling spot and the rules for the delivery of waste please contact your local municipal office. Recycling and proper disposal help to protect the environment and prevent harmful effects on health.
Manufacturer: Ningbo Sound Solution 1 &E Trading Co., Ltd Made in China
Documents / Resources
| DEAF
BONCE MM-50L Series Mid Range
Speaker
[pdf] Owner's Manual
MM-50L, MM-60L, MM-80L, MM-50L Series Mid Range Speaker, MM-50L Series, Mid
Range Speaker, Range Speaker, Speaker
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>