Deaf Bonce DB-SA252 D1 Apocalypse Subwoofer Owner’s Manual
- June 4, 2024
- Deaf Bonce
Table of Contents
Subwoofer
Owner’s Manual APOCALYPSE SERIES
DB-SA252 D1/D2
DB-SA255 D1/D2
DB-SA272 D1/D2
DB-SA275 D1/D2
DB-SA302 D1/D2
DB-SA305 D1/D2
https://alphard.audio
INTRODUCTION
Thank you for purchasing this Deaf Bonce product! Our company is committed to
the creation of extremely loud sound systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using
this product. It is especially important that you read and observe caution in
this manual. Please keep the manual in a safe and accessible place for future
reference.
SAFETY INSTRUCTIONS
-
Fasten the subwoofer properly when installing it in the vehicle. If the component is disconnected during driving, it may cause serious damage to the passengers of the vehicle or another vehicle.
-
Before installing the components, if possible store the product in its original package to avoid accidental damage to the product.
-
Be careful when installing and dismantling the subwoofer! Do not let the subwoofer drop to avoid damage to its moving parts.
-
When working with tools follow safety rules.
-
Before the installation switch off the head unit and all other audio devices to avoid their damage.
-
Make sure that the location of the subwoofer does not hinder the proper operation of mechanical and electrical devices of the vehicle.
-
Do not install components in places exposed to water, excessive humidity, high or low temperature, dust, or dirt.
ATTENTION!!! The product may be operated from +5 °C (41F) to +40 °C (104F). In case of moisture condensation, let the product dry. -
When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe, or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
-
When stretching back the speaker cables make sure that they are not in contact with sharp edges or moving mechanical devices. Make sure that they are firmly fixed and protected over the entire length.
-
The diameter of the speaker cables must be selected in accordance with the length and applied power.
-
Never stretch the cables outside of the car and near the moving parts of the car. This can lead to the destruction of the insulating layer, short circuit, and fire.
-
To protect the cables use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the parts exposed to heat.
CAUTION!!! High sound pressure can damage your health!
Please use common sense when controlling volume!
**WIRING DIAGRAMS
**
От Attention! You need to connect both voice coils of the subwoofer.
Do not expose your amplifier to loads below the value predetermined by the
manufacturer.
Various examples of connection types are given on the pages below. Use these
examples to determine the required load impedance of your connection.
Connection of terminals
Serial connection
Total impedance = ΩSub 1 + ΩSub 2 + ΩSub 3 …
Parallel connection
Schemes of enabling the load of the subwoofer
Voice coils 1+1, 2+2 Ohm
The subwoofer has voice coil D1 or D2.
One subwoofer, coilsinseries
Voice coils | Total impedance |
---|---|
1+1 Ohm | 2 Ohm |
2+2 Ohm | 4 Ohm |
One subwoofer, coils in parallel
Voice coils | Total impedance |
---|---|
1+1 Ohm | 0.5 Ohm |
2+2 Ohm | 1 Ohm |
Subwoofers in series, coils in parallel
Voice coils | Total impedance |
---|---|
1+1 Ohm | 1 Ohm |
2+2 Ohm | 2 Ohm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 1.5 Ohm |
2+2 Ohm | 3 Ohm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 2 Ohm |
2+2 Ohm | 4 Ohm |
Subwoofers in series, coils in series
Voice coils | Total impedance |
---|---|
1+1 Ohm | 4 Ohm |
2+2 Ohm | 8 Ohm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 6 Ohm |
2+2 Ohm | 12 Ohm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 8 Ohm |
2+2 Ohm | 16 Ohm |
Subwoofers in parallel, coils in series
Voice coils | Total impedance |
---|---|
1+1 Ohm | 1 Ohm |
2+2 Ohm | 2 Ohm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 0.66 Ohm |
2+2 Ohm | 1.33 Ohm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 0.5 Ohm |
2+2 Ohm | 1 Ohm |
Sub nonparallel, coils in parallel
Voice coils | Total impedance |
---|---|
1+1 Ohm | 0.25 Ohm |
2+2 Ohm | 0.5 hm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 0.16 Ohm |
2+2 Ohm | 0.33 hm |
Voice coils | Total impedance |
---|---|
1+1 Ohm | 0.125 Ohm |
2+2 Ohm | 0.25 hm |
CAUTION!!! High sound pressure can damage your health!
Please use common sense when controlling volume!
Selection of the diameter of the speaker cable
Use the table below to select the desired diameter based on the length and the
power consumption.
RECOMMENDED ENCLOSURE PARAMETERS
Bass reflex the
LWH=body volu
Model| DB-SA252 D1/D2| DB-SA255 D1/D2| DB-SA272 DI/D2| DB-SA275 D1/D2| DB-
SA302 D1/D2| DB-SA305 D1/D2
---|---|---|---|---|---|---
The recommended volume, liters / ft³| 50 / 1.8| 90 / 3.2| 55 / 2| 100 / 3.5|
55 / 2| 100 / 3.5
Port area, cm2 / inch2| 150 / 23| 200 / 31| 200 / 31| 300 / 46| 200 / 31| 300
/ 46
Port length, cm / inch| 62 / 24.4| 40 / 15.7| 70 / 27.5| 70 / 27.5| 70 / 27.5|
70 / 27.5
The port setting, Hz| 35| 35| 35| 32| 35| 32
HOW TO USE
The correct choice of the amplifier, its settings, and enclosure design
prolongs the lifetime of your subwoofer. You should select an amplifier with a
nominal power below the nominal power of the subwoofer. Proper coordination of
the head unit (HU) with the amplifier will provide a clean, the undistorted
signal fed to the subwoofer, which prevents overheating and voice coil damage.
Like any other speaker, the subwoofer has moving and stationary parts. We
strongly recommend that the moving parts of the subwoofer should be warmed up
at the beginning of the operation. Be extra careful when warming up the parts.
Warm up the subwoofer using musical material for 40 hours at medium power. If
you feel a strange smell during operation at maximum volume, you should lower
the volume of the subwoofer and let the device cool down at a low volume.
Recommended settings of the amplifier and HU: The volume of HU should not
exceed 80%. The amplifier sensitivity should be set to 50%, subsonic filter
frequency (Subsonic) should be set to 5 Hz below the port settings. For
example, if you configure the port at30 Hz, Subsonic should be set to 25 Hz.
The low pass filter LPF (the filter that cuts all frequencies above those set
for the filter) should be set to 63-80 Hz, bass boost should be set to 0.
SPECIFICATIONS
Model| DB-SA252 D1/D2| DB-SA255 D1/D2| DB-SA272 D1/D2| DB-SA275 D1/D2| DB-
SA302 D1/D2| DB-SA305 D1/D2
---|---|---|---|---|---|---
Size (inch)| 12| 15| 12| 15| 12| 15
Surround material| Foam| Foam| Foam| Foam| Foam| Foam
Cone material| Pressed paper| Pressed paper| Pressed paper| Pressed paper|
Pressed paper| Pressed paper
Frame material| Aluminum| Aluminum| Aluminum| Aluminum| , Aluminum| Aluminum
Magnet type| Ferrite| Ferrite| Ferrite| Ferrite| Ferrite| Ferrite
Power RMS (W)| 1000| 1000| 1500| 1500| 2000| 2000
Power MAX (W)| 2000| 2000| 3000| 3000| 4000| 4000
Voice coil size (inch)| 2.5| 2.5| 2.5| 2.5| 3| 3
Voice coil wire| Copper| Copper| CCAW| CCAW| CCAW| CCAW
THIELE- SMALL PARA METAERS
Impedance (Ohm) | 1+1 / 2+2 | 1+1 / 2+2 | 1+1 / 2+2 | 1+1 / 2+2 | 1+1/2+2 | 1+1/2+2 |
---|---|---|---|---|---|---|
Re (Ohm) | 0.9+0.9/ 1.9+1.9 | 0.9+0.9 / 1.9+1.9 | 0.9+0.9 / 1.9+1.9 | 0.9+0.9 / | ||
1.9+1.9 | 0.9+0.9/1.9+1.9 | 0.9+0.9/1.9+1.9 | ||||
SPL (dB) | 84.7 / 85 | 87.1 / 87.5 | 86 / 86.2 | 88 / 88.2 | 86.3 / 86.7 | 88.3 / |
88.6
Xmax (mm)| 15| 15| 18| 18| 18| 18
Fs (Hz)| 32.1 / 32.6| 32.2 / 32.9| 30.6 / 31.1| 29.7 / 31.3| 35.2 / 35.7| 31.7
/ 32
Vas (L)| 24.7 / 24.9| 61.3 / 62.1| 29.5 / 30.7| 62 / 64| 21 / 24| 61 /63
Qts| 0.36 / 0.38| 0.51 / 0.55| 0.34 / 0.36| 0.42 / 0.46| 0.31/0.34| 0.4 / 0.43
BL| 22.7 / 23.2| 20.1 / 20.8| 20.1 / 20.8| 18.6 / 19.1| 20 / 20.8| 18.5 / 18.7
This specified sensitivity is not directly connected with the sound pressure in the vehicle and therefore should not be used as the sole indicator for comparison with other subwoofers.
DIMENSIONS
BOX CONTENTS
- Subwoofer – 1 pc.
- Owner’s Manual -1 pc.
- Warranty card -1 pc.
WARRANTY AND MAINTENANCE INFO
Deaf Bonce products are warranted against defects concerning materials and
their manufacturing under normal functioning conditions.
While the product is under warranty, defective parts will be repaired or
replaced at the manufacturer’s decision. The defective product, along with a
notification about it, must be returned to the dealer from which it was
purchased together with the warranty certificate duly filled in, complete with
the original packaging. If the product is no longer under warranty, it will be
repaired at the current costs. Our company does not undertake any liability
for damages due to transportation. Our company does not take any
responsibility for costs or loss of profit due to the impossibility to use the
product, other accidental or consequential costs, expenses, or damages
suffered by the customer. Warranty according to laws in force. For more
information visit our website and carefully read the warranty card.
The manufacturer reserves the right to change design and specification without
prior notice.
10. INFORMATION ON DISPOSAL OF THE ELECTRICAL AND ELECTRONIC EQUIPMENT (FOR THE EUROPEAN COUNTRIES WITH SEPARATE WASTE COLLECTION)
Items marked “crisscrossed wheeled bin” are not allowed to be disposed of together with usual household waste. These electrical and electronic products should be disposed of in special reception centers, equipped for recycling such products and components. For information about the location of the nearest disposal/recycling spot and the rules of delivery of waste please contact your local municipal office. Recycling and proper disposal help to protect the environment and prevent harmful effects on health.
https://deafbonce.com/subwoofers/?series=apocalypse
Manufacturer: Ningbo Sound Solution I &E Trading Co., Ltd
Made in China
https://alphard.audio
https://alphard.audio
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>