Deaf Bonce MLT-15 HF Speaker User Manual

May 15, 2024
Deaf Bonce

Deaf Bonce MLT-15 HF Speaker

Deaf-Bonce-MLT-15-HF-Speaker-PRODUCT

Specifications

  • Model: MLT-15
  • Size: 2.2 inch / 56 mm
  • Diaphragm Material: Aluminum
  • Body Material: ABS Plastic
  • Magnet Type: Neodymium
  • Power RMS: 25W
  • Power MAX: 50W
  • Voice Coil Size: 1 inch
  • Voice Coil Wire: CCAW
  • Frequency Response: 5,000 – 20,000 Hz
  • Impedance: 4 Ohm
  • SPL: 104dB

Safety Instructions

  1. Fasten the speakers properly when installing them in the vehicle.
  2. Store the product in its original package before installation to avoid accidental damage.
  3. Be cautious with high sound pressure to prevent damage to your health.

Wiring Diagrams
Make sure to follow the wiring diagrams provided in the manual for proper connection and impedance calculations.

Filtering & Amplifier Settings
Set the high pass filter (HPF) to 8 kHz (12 dB/Oct) and use recommended amplifiers for optimum performance.

Dimensions & Installation
Refer to the dimensions provided for installation guidance. Follow the instructions for mounting cup installation carefully.

FAQ

  1. Q: Can I use the MLT-15 speakers in parallel connection?
    A: Yes, you can use the speakers in parallel connection, but make sure to calculate the total impedance correctly to avoid any issues.

  2. Q: What is the warranty period for the MLT-15 speakers?
    A: The warranty period and after-sales service information can be found in the manual. Please refer to the specific details provided.

OWNER`S MANUAL

MLT-15

https://alphard.audio

INTRODUCTION

Thank you for purchasing of this Deaf Bonce product! Our company is committed to the creation of extremely loud sound systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you read and observe cautions in this manual. Please keep the manual in a safe and accessible place for future reference.

SAFETY  INSTRUCTIONS

  1. Fasten the speakers properly when installing it in the vehicle. If the component is disconnected during driving, it may cause serious damage to the passengers of the vehicle or another vehicle.
  2. Before installing the components, if possible store the product in it’s original package to avoid accidental damage to the product.
  3. Be careful when installing and dismantling the speaker! Do not let the speaker drop to avoid damage of its moving parts.
  4. When working with tools follow safety rules.
  5. Before the installation switch off the head unit and all other audio devices to avoid their damage.
  6. Make sure that the location of the speaker does not hinder the proper operation of mechanical and electrical devices of the vehicle.
  7. Do not install components in places exposed to water, excessive humidity, high or low temperature, dust or dirt. ATTENTION!!! The product may be operated at +5 °C (41F) to +40 °C (104F). In case of moisture condensation, let the product to dry.
  8. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
  9. When stretching back the speaker cables make sure that they are not in contact with sharp edges or moving mechanical devices. Make sure that they are firmly fixed and protected over the entire length.
  10. The diameter of the speaker cables must be selected in accordance with the length and applied power.
  11. Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the insulating layer, short circuit, and fire.
  12. To protect the cables use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the parts exposed to heat.

CAUTION!!! High sound pressure can damage your health!Please use the common sense when controlling volume!

WIRING  DIAGRAMS

Do not expose your amplifier to loads below the value predetermined by the manufacturer.
Various examples of connection types are given at the pages below. Use these examples to determine the required load impedance of your connection.

Serial connection of the speakers

Deaf-Bonce-MLT-15-HF-Speaker-16

Parallel connection of the speakers

Deaf-Bonce-MLT-15-HF-Speaker-18

Mixed connection of the speakers

Deaf-Bonce-MLT-15-HF-Speaker-19

CAUTION!!! High sound pressure can damage your health! Please use the common sense when controlling volume!

Selection of the diameter of speaker cables
Use the table below to select the desired diameter based on the length and the power consumption.

Deaf-Bonce-MLT-15-HF-Speaker-8

FILTERING, RECOMMENDED AMPLIFIER SETTINGS

The correct choice of amplifier, its settings, filtering and enclosure largely influence on the lifespan of your audio system. You should select an amplifier with a nominal power, not exceeding the nominal power of the speakers. Proper coordination of the head unit (HU) with the amplifier will allow to get clean, undistorted signal applied to the component to prevent overheating and voice coil damage. Recommended settings of the amplifier and HU: Volume of HU should not exceed 80%. The amplifier sensitivity should be set to 50%.

The recommended filter settings
The high pass filter HPF (the filter that cuts all frequencies below those set for the filter) should be set to 8 kHz (12 dB/Oct) Recommended amplifiers: MLA-60.2, MLA-60.4, MLA-70.2XS, MLA-80.4XS, MLA-100.2, MLA-100.4, MLA-150.2XS, MLA-160.2, MLA-160.4.

Deaf-Bonce-MLT-15-HF-Speaker-98

SPECIFICATIONS

Deaf-Bonce-MLT-15-HF-Speaker-20

DIMENSIONS

Deaf-Bonce-MLT-15-HF-Speaker-9 Deaf-Bonce-
MLT-15-HF-Speaker-10

Connection of terminals

Installation

  1. Mounting cup installation Attention! Before installing the tweeters, make sure to lock the mounting cup by turning it clockwise until it clicks, as shown in the diagrams below. Deaf-Bonce-MLT-15-HF-Speaker-12
  2. Installation with the use of a universal mounting cup
  3. Installation with use of a mounting cup for recessed installation Deaf-Bonce-MLT-15-HF-Speaker-13

BOX CONTENTS

  1. High-frequency speaker – 2 pcs.
  2. Universal mounting cup – 2 pcs.
  3. Mounting cup for recessed installation – 2 pcs.
  4. Owner’s manual – 1 pc.
  5. Warranty card – 1 pc.

WARRANTY PERIOD, AFTER-SALES SERVICE AND SERVICE LIFE INFORMATION

Each Deaf Bonce product is warranted to be free from defects in materials and workmanship under normal use and service.
The warranty period for the product is 12 (twelve) months from the date on which the product is transferred to the consumer (this date shall be deemed to be the date on which the consumer starts using the product).
During the warranty period, defective parts will be repaired or replaced at the discretion of the manufacturer provided that there are grounds for doing so under the laws of the consumer’s country. The defective product must be returned to the dealer from whom it was purchased together with the duly filled out warranty certificate, complete, with original packaging.
Our company shall not be liable for any damage caused by transportation. Our company shall not be liable for any expenses or lost profits arising out of or in connection with the use or inability to use the product or any other incidental or indirect costs, expenses, or damages incurred by the customer. The warranty is valid in accordance with the laws currently in force. For more information, please visit our company website and refer to the warranty card.

  • The manufacturer reserves the right to change the design and specification of the product without prior notice. The service life of the product is 12 (twelve) months from the date on which the product is transferred to the consumer (this date shall be deemed to be the date on which the consumer starts using the product).
  • The product or any part (component) of the product must not be used in any way (including, but not limited to use for intended or any other purpose, transportation, storage, modification/alteration/improvement/upgrade) after the expiry of the service life.

At the end of its service life, the product must be disposed of.

INFORMATION ON DISPOSAL OF THE ELECTRICAL AND ELECTRONIC EQUIPMENT (FOR

THE EUROPEAN COUNTRIES WITH SEPARATE W ASTE COLLECTION)

Items marked “crisscrossed wheeled bin” are not allowed to be disposed of together with usual household waste. These electrical and electronic products should be disposed of in special reception centers, equipped for recycling such products and components. For information about the location of the nearest disposal / recycling spot and the rules of delivery of waste please contact your local municipal office. Recycling and proper disposal helps to protect the environment and prevent harmful effects on health.

Manufacturer: Ningbo Basshead I&E Trading Co., Ltd Made in China

https://alphard.audio

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Deaf Bonce User Manuals

Related Manuals