cecotec Power Espresso 20 Pecan Pro Espresso Machine Instruction Manual

June 14, 2024
cecotec

POWER ESPRESSO 20 PECAN PRO
Espresso Machine
Instruction manual

SAFETY INSTRUCTIONS

Read these instructions thoroughly before using the device. Keep this instruction manual for future reference or new users.

  • All safety instructions must be closely followed when using the appliance.
  • This symbol means ‘caution: hot surface.’ Accessible surfaces are likely to heat up during use. Be careful not to burn yourself.
  • This device is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels, and offices.
  • The appliance must not be used by children. Keep this appliance and its power cord out of their reach.
  • This appliance can be used by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
  • Children must not play with the appliance. Cleaning and user maintenance should not be carried out by unsupervised children.
  • WARNING: the filling opening or the water tank must not be opened during operation.
  • WARNING: take precautions to avoid spillage of liquids on any electrical conductors.
  • WARNING: incorrect or improper use can be dangerous for the user and damage the appliance. Use the appliance only for the purposes described in this manual. The surface of the heating element is subject to residual heat after use.
  • Ensure that the mains voltage matches the voltage specified on the appliance rating label and that the plug is earthed.
  • Do not immerse the cable, plug, or any other non-removable part of the device in water or any other liquid or expose electrical connections to water. Make sure your hands are dry before handling the plug or switching on the device.
  • Warning: if the device falls accidentally in water, unplug it immediately. Do not touch the water!
  • Check the power cable regularly for visible damage. If the cable is damaged, it must be replaced by the official Cecotec Technical Support Service
  • in order to avoid any type of danger.
  • WARNING: do not use the appliance if its cable, plug, or housing are damaged, nor after it malfunctions or has been dropped or damaged in any way.
  • Do not twist, bend, pull, or damage the power cable. Protect it from sharp edges and heat sources. Do not allow the cable to touch hot surfaces. Do not let the cable hang over the edge of the working surface or worktop.
  • This appliance is not intended to be operated by means of an external timer or separate remote-control system.
  • Turn off and unplug the appliance from the mains supply when not in use and before cleaning it. Pull from the plug, not the cable, to disconnect it from the outlet.
  • Supervise children to prevent them from playing with the appliance. Close supervision is necessary when the appliance is being used by or near children.
  • Place the appliance on a dry, stable, flat, heat-resistant surface.
  • Do not use the appliance under the following circumstances:
  • On or near a gas or electric hob, in heated ovens, or near open flames.
  • On soft surfaces (such as carpets) or where it may tip over during use.
  • Outdoors or in areas with high humidity levels.
  • Do not cover the appliance during operation.
  • Never leave the device unattended during use. Unplug it from the mains supply when you finish using it or when you leave the room.
  • Do not try to repair the appliance by yourself. Contact the official Cecotec Technical Support Service for advice.
  • Cleaning and maintenance must be carried out according to this instruction manual to make sure the appliance functions properly. Turn off and unplug the appliance before moving and cleaning it.
  • Do not wash the appliance in dishwashers.
  • No liability is accepted for any eventual damage or personal injuries derived from misuse or non-compliance with this instruction manual.

PARTS AND COMPONENTS

Fig. 1

1. Steam indicator light 11. Drip grid
2. Steam button 12. Drip tray
3. Coffee indicator light 13. Lid
4. Power indicator light 14. Handle
5. Coffee button 15. Tank cover
6. Power button 16. Water tank cover
7. Filter 17. Steam knob
8. Filter holder lever 18. Main body
9. Portafilter 19. Measuring spoon
10. Base 20. Steam wand

NOTE:
the graphics in this manual are schematic representations and may not exactly match the device.

BEFORE USE

  • This appliance is packaged in a way as to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the device when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
  • Make sure all parts and components are included and in good conditions. If there is any piece missing or in bad conditions, contact the official Cecotec Technical Support Service immediately.

Box content

  • Coffee machine
  • Single-coffee filter
  • Double-coffee filter
  • Measuring spoon with tamper
  • Portafilter
  •  Instruction manual

OPERATION

Preheating

  • To make a good cup of coffee, it is advisable to preheat the coffee machine before brewing, including the portafilter, filter and cup, so that the taste of the coffee is not altered by any cold elements.
  • Remove the detachable tank and open the tank cover to fill it with the desired amount of water. The water level must not exceed the “MAX” mark on the tank. After filling the tank, put it back in place. Place the tank into the appliance properly.
  • Insert the stainless-steel filter into the portafilter. Ensure that the portafilter tube is aligned with the slot in the machine. Then, install the portafilter into the coffee machine from the unlocked position by turning it counterclockwise until it locks into the locked position.
  • Place an espresso cup on the removable grille.
  • Plug the appliance into a power supply.
  • Make sure the steam knob is in the off position.
  • Once the preheating process is completed, the power indicator light will stop flashing and will remain steady. Press the coffee button and switch off the pump immediately after the water comes out.
  • When the coffee indicator light lights up, press the coffee button again to make hot water come out. When the indicator light switches off, close the pump. Steam preheating is then finished.

Preparing an espresso

  1. Turn the portafilter counterclockwise to remove it. Add the ground coffee into the filter with the measuring spoon. One tablespoon of ground coffee makes one cup. Then, use the other end of the measuring spoon to press the ground coffee.
  2.  Insert the stainless-steel filter into the portafilter. Ensure that the portafilter tube is aligned with the slot in the machine. Then, install the portafilter into the coffee machine from the unlocked position by turning it counterclockwise until it locks into the  locked position.
  3. Pour hot water into the cup and allow it to heat up. After that, empty the cup and dry it. Finally, put the hot cup on the drip grid.
  4. After that, the coffee indicator light will light up; if it switches off, wait a few seconds. When the indicator light remains steady, press the coffee button. Pres the coffee button again when you have obtained the desired amount of coffee, the water pump will stop working.

WARNING: do not leave the machine unattended during preparation, as it may be necessary to handle the machine manually.

  • When you have finished brewing coffee, remove the portafilter from the machine by turning it to the left and then, remove the coffee residue from the filter by pressing the filter holder lever.
  • Let the coffee machine cool down completely and rinse the removable parts under the tap.
  • The brewing time for a single coffee is a maximum of 60 seconds. The water pump will stop running if the running time exceeds 60 seconds. The brewing time can be adjusted by following the steps below. Press and hold the coffee button for 3 seconds in standby mode, the coffee indicator light will flash. Press the coffee button again within 5 seconds to start the water pump. Press the coffee button again so that the water pump stops operating. The configuration is then complete. The adjustable brewing time ranges from 15 to 60 seconds.

Preparing hot water

  • Once the preheating process is completed, the power indicator light will stop flashing and will remain steady. Then, press the coffee button, the water pump will start pumping water. Turn the steam knob to the steam/hot water position so that hot water comes out from the steam wand. To stop hot water preparation, press the coffee button again. The hot water function is used to heat the cup, prepare tea or to cool the machine.
  • Refer to the “Preparing an espresso” section when you need to adjust the hot water brewing time.

Preparing a cappuccino
To prepare a cappuccino, fill the espresso cup with frothed milk.
Method

  1. To prepare a cappuccino, first prepare an espresso following the steps in the section “Preparing an espresso”. Make sure the steam knob is in the off position.

  2. Press the steam button, the coffee indicator light will light up. Then, wait until the steam indicator light also lights up.
    Note: during the preheating process, the steam indicator light will turn on and off to maintain the desired temperature.

  3. Fill a jug with about 100 ml of cold whole milk for each cappuccino you wish to prepare, it is recommended to use cold whole milk (not hot!).
    Note: when choosing the size of the jug, it is recommended that the diameter of the jug should not be less than 70±5 mm. Also, bear in mind that milk increases in volume by a factor of two, so make sure that the jug is high enough.

  4. Slowly turn the steam knob counterclockwise so that steam comes out from the steamer.
    Note: Never turn the steam knob sharply, as the machine will emit a lot of steam in a short time, which may increase the risk of scalding.

  5. Insert the steam wand into the milk about two centimeters deep and froth the milk by moving the jug up and down.

  6. When you have finished frothing the milk, turn the steam knob to the off position.
    Note: The steam outlet nozzle should be cleaned with a damp sponge immediately after steam stops coming out but be careful not to burn yourself.

  7.  Pour the frothed milk into the coffee cup; your cappuccino is now ready. Sweeten to taste and if desired, sprinkle the froth with a little cocoa powder.

  8.  Press the power button to cut off the power supply. All indicator lights will turn off.
    WARNING: after you have finished using the steam function, press the coffee button. If the coffee and steam indicator lights flash rapidly, the machine temperature is too high. Let the machine cool down for at least 5 minutes, or activate the hot water function to cool down the machine. The machine will automatically stop dispensing water when the temperature decreases. If you prepare coffee without allowing the machine to cool down completely, the coffee will burn and the portafilter will overflow.

RESET
After preheating is complete, press and hold the power button, the coffee button, and the steam button at the same time for 3 seconds The corresponding indicator lights will flash 3 times, so the factory reset is complete.

CLEANING AND MAINTENANCE

  1. Disconnect the power supply and allow the machine to cool down completely before cleaning.

  2. Regularly clean the main housing and water tank with a sponge. Thoroughly wash and dry the drip tray and grid.
    Note: do not use alcohol or solvents to clean the machine. Never immerse the housing in water for cleaning.

  3. Remove the metal portafilter from the filter by turning it clockwise and remove any coffee residue. Clean with water and detergent and dry thoroughly.

  4. Clean all accessories in water and dry them thoroughly.

Cleaning mineral deposits

  • The descaling warning will occur automatically and will mean that 500 cumulative cycles have elapsed.
  • All indicator lights will flash rapidly 5 times once preheating is complete. Once descaling has been completed, the machine will return to its normal state.
  1. Fill the water tank with water and a descaling solution up to the MAX level indicated on the water tank (the scale of water and descaler is 4:1. Follow the instructions on the package of the descaler.). Instead of a descaler, you can also use a “homemade descaler” made from citric acid (available in pharmacies or drugstores) by mixing 100 parts of water with 3 parts citric acid.
  2. Place the metal portafilter (with no coffee inside) and the jug.
  3. Press the power button once, its red indicator light will light up; press the power button again and wait for the machine to start heating up.
  4. When the power indicator light lights up, heating is complete. Press the coffee button and prepare two cups of coffee. Then, close the pump and wait 5 seconds.
  5. Press the coffee/steam button, the coffee/steam indicator light lights up. Then, wait until the steam indicator light also lights up. Emit steam for 2 minutes by turning the steam knob to the steam/hot water position; then, turn the knob back to the off position to stop generating steam.
  6. Press the power button to stop the machine immediately and let the descaler work for 15 minutes.
  7. Restart the coffee machine and repeat steps 4 and 5 at least 3 times.
  8. Next, press the coffee/steam button, the coffee indicator light will light up. Then, press the power button to prepare coffee until no descaler is left.
  9. Next, prepare coffee (without coffee powder) with tap water at MAX level, and repeat steps 4 to 6 3 times (no need to wait 15 minutes at step 6).
  10. Repeat step 7 at least 3 times to ensure that the steam wand is clean.
  11. Follow the procedure below to cancel the descaling warning once it has been completed. Press and hold the coffee button and the steam button for 3 seconds at the same time in standby mode, then their corresponding indicator lights will flash rapidly 3 times. This will mean that the descaling warning has been cancelled and the duty cycle is back to zero.

TROUBLESHOOTING

Problem Cause Solution
The metal parts of the machine are rusted The descaler used is not the right
one. May corrode metal parts of the tank. Use the descaler recommended by the

manufacturer.
The bottom of the machine Leaks| There is too much water in the drip tray.| Empty the drip tray.
The coffee machine does not work properly.| Contact the official Cecotec Technical Support Service.
The water flows out of the sides of the stainless-steel filter| There is ground coffee on the edge of the filter| Wipe off any coffee residue.
Acid (vinegar) taste in coffee| The device has not been properly cleaned after descaling.| Clean the coffee machine several times by following the appropriate steps.
Ground coffee has been stored in a hot, wet place for a Long time. The ground coffee has gone bad.| Use fresh ground coffee, or store the it in a cool, dry place. After opening a package of ground coffee, reseal it tightly and store it in a refrigerator to maintain its freshness.
The machine does not turn on| The power cable is not properly plugged in.| Plug the power cord correctly into a power outlet. If the machine still does not work, contact the official Cicotte’s Technical Support Service.
Steam cannot make foam| The steam indicator light is not lit.| Only when the steam indicator light is lit can the steam function be used for frothing.
Container is too large, or shape does not fit.| Use a tall, narrow cup.
You have used skimmed milk.| Use whole or semi-skimmed milk.

TECHNICAL SPECIFICATIONS

Product: Power Espresso 20 Pecan Pro
Product reference: 01725
Voltage: 220-240 V ~
Frequency: 50 Hz
Rated power: 1100 W
Av. Reyes Católicos, 60, 46910, Alfafar, Valencia (Spain)
Tax number: B-97937890
www.cecotec.es
Technical specifications may change without prior notification to improve product quality.
Made in China
Designed in Spain

DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

**** This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/ batteries/ accumulators and take them to a collection point designated by the local authorities.
Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.
Compliance with the above guidelines will help protecting the environment.

TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.
It is recommended that repairs be carried out by qualified personnel.
If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cerotic Technical Support Service at +34 963 210 728.

The intellectual property rights over the texts in this manual belong to CECOTEC
INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

www.cecotec.es
Cerotic Innovations S.L.
Av. Reyes Calicos, 60
46910, Alf afar (Valencia), Spain
RP01230907

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

cecotec User Manuals

Related Manuals