KIWI design Quest 2 Clipon Headphones User Manual
- June 14, 2024
- KIWI design
Table of Contents
Clip-on Headphones
for Quest 2
User Manual
- Headphone cable
- Supporting arm
- Headphone
- Fastening tape
- Adjustable connector
- Stretchable clip
How to use
(1)
1. Distinguish the L and R marks inside the stretchable clips of the clip-on headphones.
(2)
2. Buckle the stretchable clip on top of the corresponding side strap.
(3)
3. Hold the headphone supporting arm and pull it down to extend the stretchable clip, then push the clip against the side strap and release. The stretchable clip will automatically buckle onto the side strap.
(4)
4. Install the other headphone on the opposite side strap repeating steps 2 to 4 above.
(5)
5. Plug the headphone cable into the headset, and fasten the headphone cable to the side straps with the fastening tapes.
(6)
6. While wearing the assembled headset, multi-adjust your headphone up/down, inside/outside, and in different angles, and directions to perfectly fit your ear’s position.
(7)
7. To disassemble – One hand holds the side strap, and the other holds the headphone supporting arm. Pull down the supporting arm to extend the stretchable clip, then carefully rotate the stretchable clip outward to release the headphones from the side strap.
Tips: For better performance of the headphones, please do not over-rotate.
Clip-on Headphones
Safety and Warranty Guidelines
Product Specification
| Model No. | QA03 |
|---|---|
| Product Size | 4.5 x 2.4 x 2.1 inch |
| Driver Units | 40mm |
| Rated Power | 20mW |
| Maximum Power | 30mW |
| Headphone Jack | 3.5mm |
| Surface Resistance | 20 ohms |
| Waterproof Level | IPX5 |
| Material | PU, ABS Plastic, Memory Foam |
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 ) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
CAN ICES-003 (B) / NMB-003 (B).
EU Declaration of Conformity
Hereby, Shenzhen hongjiantou Technology Co., Ltd. declares that this equipment is in compliance with Directives 2014/30/EU & 2011/65/EU & 2001/95/EC.
The full text of the EU declaration of conformity is available at the
following internet address:
https://www.kiwidesign.com
The following importer is the responsible party (for EU matters only):
AMZ ECREP SL
Calle Gran Via 49, 7 Dch. Madrid 28013 Spain
GB Declaration of Conformity
Hereby, Shenzhen hongjiantou Technology Co., Ltd. declares that this equipment is in compliance with the following Directives: The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 & Electrical Equipment (Safety) Regulations 2016 & Electromagnetic Compatibility Regulations 2016.
The full text of the GB declaration of conformity is available at the
following internet address:
https://www.kiwidesign.com
The following importer is the responsible party (for UK matters only):
EVATOST CONSULTING LTD
Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales,
CF15 7QR
This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Customer Service
We hope you never have the need, but if you do, our service is friendly and hassle-free.
30-day money-back guarantee
18-month warranty
Lifetime user support
: customerservice@kiwidesign.com
: @KIWIdesign_shop
: @AlexbyKiwidesign
: www.kiwidesign.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>