KIWI design QA01B Comfort Battery Audio Head Strap Instructions
- June 14, 2024
- KIWI design
Table of Contents
AlO Comfort Battery
Audio Strap
For Quest 2
Safety and Warranty Guidelines
Product Electrical Specification
| Model No. | QA01B |
|---|---|
| Battery Type | Lithium-ion Polymer |
| Battery Capacity | 6400mAh 3.85V 24.64Wh |
| Input | 5.0V=2.0A |
| Output | 5.0V=2.4A |
| Size | 7.8 x 10.2 x 1.8 inch |
| Operating Temperature | 0°C-45°C/32°F-113°F, min. humidity 5%, max humidity 95% |
RH (non-condensing)
Storage Temperature| -20°C-45°C/-4°F-113°F, 85% RH
To charge the QA01B only| About 4h
---|---
To charge the Quest 2 by the QA01B only| About 3h
To charge the Quest 2 and the QA01B together| About 5h
- We recommend using the original adapter and cable from the Quest 2 o charge this head strap, or other qualified power adapters and cables certified with the fast charging protocol. Charging time may vary depending on different types of ‘power adapters and cables
Health and Safety Warnings
“This head strap contains two 3200mAh Lithium-lon cells and an electronic circuit board inside. Improper use of the head strap may result in a fire, explosion, battery leakage, or other hazards. To reduce the risk of personal injury, discomfort, or property damage, please ensure that each user carefully reads the warnings below before using this head strap.
- The battery in the head strap is not user-replaceable or serviceable. Do not attempt to open your battery head strap to access the battery, open, repair, o replace the battery. Please contact KIWI design, if you need battery management support for your device.
- Only charge your head strap with a qualified approved power adapter and cable. Do not use other cables or power adapters. If you are unsure if a cable or power adapter is compatible with this product, contact KIWI design support. Only use the original headset adapter and cable for charging,
- Periodically inspect connection cords, battery indicator, charger port, as well as your own power adapter and cable for damage or signs of wear. Do not use your power accessories if the prong(s), enclosure, connector port, connector cable, or any part is damaged, cracked, or exposed.
- Do not disassemble, crush, bend or deform, puncture, shred or put a high degree of pressure on the head strap. This may cause leakage or an internal short-circuit in the battery, resulting in overheating.
- Avoid dropping your head strap. Dropping it, especially on a hard surface, may cause damage to the product and the battery inside. Inspect your head strap for visual damage before each use.
- Do not let your head strap get wet or come in contact with liquids. Even though it may dry and appear to operate normally, the battery contacts o circuitry could slowly corrode and pose a safety hazard
- Do not place your head strap in areas that may get very hot, such as on or near a cooking surface, cooking appliance, iron, or radiator, or in direct sunlight. Excessive heat may damage the head strap or the battery inside and could cause the battery to become combustible. Do not dry a wet or damp head strap with an appliance or heat source such as a microwave oven, hairdryer, iron, or radiator. Avoid leaving it in a car in high temperatures.
- In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
- Always ensure that the head strap has adequate ventilation and airflow while in use or charging. Covering it with materials that significantly affect airflow (Such as a pillow, blanket, or part of your body) may affect its performance and pose a possible risk of becoming combustible.
- Adults should make sure children (age 13 and older) use this head strap in accordance with these Health and Safety Warnings.
- Recycle or dispose of your head strap properly. Do not dispose of the head strap in a fire or incinerator, as the battery inside may explode when overheated. Dispose of separately from household waste.
FCC Statement
“This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference. will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Canada Statement
‘This device complies with Canadian ICES-003 Operation is subject to the
following two conditions: (1) This device may not cause interference. (2) This
device must accept any interference, including interference that may cause
undesired operation of the device.
GB Declaration of Conformity
Hereby, Shenzhen hongjiantou Technology Co. Ltd. declares that this equipment
is in compliance with the following Directives: The Restriction of the Use of
Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012 & Electrical Equipment (Safety) Regulations 2016 &
Electromagnetic Compatibility Regulations 2016,
The full text of the GB declaration of conformity is available at the
following internet address; https://www.kiwidesign.com
The following importer is the responsible party (for UK matters only):
EVATOST CONSULTING LTD
Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales,
CF15 7GR
EU Declaration of Conformity
Hereby, Shenzhen hongjiantou Technology Co., Ltd. declares that this equipment
is in compliance with the following Directives: 2014/35/EU & 2014/30/EU &
2011/65/EU. The full text of the EU declaration of conformity is available at
the following internet address
https://www.Kiwidesign.com
‘The following importer is the responsible party (for EU matters only):
AMZ ECREP SL.
Calle Gran Via 49, 7 Dch. Madrid 28013 Spain
**** This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>