KTYU 3 in 1 Cordless Weed Wacker Instructions

3 IN 1:Trimmer/Edger/Pole Saw
Instruction Manual

GENERAL SAFETY BULLETIN FOR POWER TOOLS

WARNING! Read all warnings and all instructions。 Failure to follow the warnings and instructions below can result in electric shock, fire, or serious injury. Keep all warnings and instructions for reference. In all warnings below, the term “power tool” refers to both mains powered (corded) and lithium battery powered (cordless) power tools.
General Power Tool Safety Warning – Workplace Safety

1. Keep your workplace clean and bright. Messy and dark sites can cause accidents.

2. Do not operate power tools in explosive environments, such as those with flammable liquids, gases or dusts.
   Sparks from power tools can ignite dust or gas, creating an electric shock hazard.

3. Keep children and bystanders away from power tools. Inattentiveness can cause the operator to lose control of the tool.

General Power Tool Safety Warning – Electrical Safety

1. Power tool plugs must be matched to the socket or battery packs must be matched to the machine. Plugs or battery packs must never be modified in any way, and no adapter plugs can be used for power tools that require grounding. Using unmodified plugs and matching sockets/unmodified battery packs and matching machines will reduce the risk of electric shock.
2. Avoid human contact with grounded surfaces such as pipes, heat sinks and refrigerators.If you physically ground yourself it will increase the risk of electric shock.
3. Do not expose power tools to rain or wet conditions. Water entering the power tool will increase the risk of electric shock.
4. Do not abuse electrical cords. Never carry, pull, or unplug power tools with electrical cords.Never carry, pull, or unplug power tools by their cords.Keep cords away from heat, oil, sharp edges ormoving parts. Damaged or tangled cords can increase the risk of electric shock.
5. Do not abuse electrical cords. Never carry, pull or unplug a power tool by its cord. Keep cords away from heat, oil, sharp edges or moving parts. Damaged or tangled cords increase the risk of electric shock.
6. If operation of the power tool in a wet environment is unavoidable, use a residual current action protector (RCD).
   The use of an RCD will reduce the risk of electric shock.

General Power Tool Safety Warning – Personal Safety

1. Stay alert, pay attention to what you are doing when operating power tools and stay awake. Do not operate power tools when you are tired, or when you are having a reaction to drugs, alcohol or treatment. Momentary negligence  while operating a power tool can result in serious personal injury.
2. Use personal protective equipment. Always wear goggles. Safety devices such as dust masks, non-slip safety shoes, helmets, hearing protection, etc. in appropriate conditions can reduce personal injury.
3. Prevents accidental starting. When the switch is connected to the power supply or battery compartment, make sure the switch is in the OFF position when picking up or handling the tool. Fingers on a switch that is powered on or plugged in when the switch is on may cause a hazard.
4. Remove all adjustment keys or wrenches before powering on the power tool. Wrenches or keys left on rotating parts of the power tool can cause personal injury. Do not extend your hands too far and always be aware of your foothold and body balance. This gives you good control of the power tool in the event of an accident. Dress appropriately. Do not wear loose clothing or accessories.Keep clothing, gloves and hair away from moving parts. Loose clothing, accessories or long hair may get caught in moving parts.
5. If devices are provided for connection to chip removal devices and dust collection equipment, make sure they are well connected and used properly. The use of these devices can reduce the risk of dust and debris.

General power tool safety warningsPower tool use and precautions

1. Don’t abuse power tools; use the proper power tool for the purpose. Choosing a properly designed power tool will make you work more efficiently and safely.
2. If the switch does not turn on or off the power to the tool, the power tool should not be used. Power tools that cannot be controlled by a switch are dangerous and must be repaired.
3. Before making any adjustments, replacing accessories or storing the power tool, it must be unplugged from the power source and/or the battery compartment must be disconnected from the tool.This protective measure will reduce the risk of accidental start-up of the tool.
4. Store unused power tools out of the reach of children and do not allow anyone unfamiliar with the power tool or ignorant of these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check that moving parts are not adjusted in place or stuck, and check for broken parts and other conditions that affect the operation of the power tool. If damaged, power tools should be repaired before use; many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. A well maintained tool with a sharp cutting edge is less likely to jam and easier to control. Use power tools, accessories and tool bits according to the instruction manual, taking into account the operating conditions and the work to be performed.Using power tools for operations that are not compatible with their intended use may be hazardous.

General Power Tool Safety Warning – Repair

1. Send your power tool to a professional repairer to be repaired using the same spare parts. This will ensure the safety of the power tool being repaired.
2. If the power cord must be replaced, it must be replaced by the manufacturer or agent in order to avoid danger.

BATTERY AND CHARGER INSTRUCTIONS

Warning!
To avoid safety hazards, always ensure that the reversing toggle is in the center position when installing or removing the battery pack, which will lock the switch and prevent accidental triggering. Please note that the battery pack is only partially charged upon delivery. To maximize the battery’s power, it must be fully charged using the charger before its first use. *Installing or removing the battery pack

1. Install the battery pack
   As illustrated in the figure below, when inserting the battery pack, make sure to insert it correctly. Please ensure that you hear a “click” sound, which indicates that the battery pack is securely installed in the machine. If not properly installed, the battery pack may accidentally fall out of the case, which could lead to injuries to the operator or others. Also, avoid using excessive force or tapping with other objects when inserting the battery pack.* Note: Only the specified model of battery pack can be used. The use of battery packs of other brands carries the risk of injury as well as personal injury and property damage due to battery exptosion, in addition damage to the machine may also occur.

2. Remove the battery pack
   The battery pack is under the handle of the machine, press the battery pack button, and then force pull the battery pack outward.
   *Note: Do not force the battery pack to pull out.

3. Power display
   The power display is located at the body where the battery pack is connected. The status of the power display is as the following table.

*Some models do not have power display or the location is different, please refer to the physical

• Battery charging method
  This charger is suitable for charging the specified type of lithium-ion battery under general environmental conditions.

The performance and specifications of this product are shown in the following table

*Note:* We reserve the right to improve the specifications without prior notice.
Charging operation**

1. Plug the charger into the socket after the green light is always on to enter the charging waiting state.
2. Then insert the battery pack into the charger and the red light will start charging.

*Note: Please make sure that the AC voltage parameters meet the voltage requirements on the charger nameplate!!!

The relationship between indicator status and charging status is detailed in the following table:

*Battery pack failure detection
The charger can be used to detect faults caused by the battery pack, which are identified by the red indicator and the status of the green indicator. In the event of a fault, the battery pack should be reinserted into the charger. If the fault persists, switch to another battery pack. If the new battery pack can be charged properly, the original battery pack may be damaged. If the new pack still has the same fault indication, the charger may be damaged and needs to be serviced.

SUPPLEMENTARY SAFETY RULES FOR BATTERY PACKS

1. Before doing any work (e.g. tool change, inspection, maintenance, handling, storage, etc.), the battery pack must be removed by setting the reversing switch slider (switch lock).
2. Check that the battery pack is properly installed before using the machine.
3. When charging, the battery pack will become slightly hotter, which is normal.
4. Do not charge a damaged battery pack.
5. After charging, please disconnect the battery pack from the charger after the power is disconnected. Do not leave the battery pack in the charger for a long time.
6. Do not plug a charged battery pack into the charger when the machine is not in use.
7. Do not attempt to disassemble the battery pack, and when maintenance or repair is required, refer it to professional service personnel. Improper assembly can cause the risk of electric shock or fire.
8. Do not short-circuit the battery pack.
9. Do not put the battery pack into the fire, it will cause the risk of explosion.
10. Prohibit dropping, shaking, and hitting the battery pack.
11. Do not use the battery pack as a hammer, knocking will cause accidental short circuit, fire or even explosion.
12. The battery pack must be kept away from heat or flame! Do not put the battery pack on the heater or expose it to strong sunlight, the temperature is too high and there is a risk of explosion.
13. The workplace must be well ventilated. Toxic gases emitted from battery packs that are not used in accordance with the prescribed requirements or that are damaged can cause personal injury.
14. Battery packs may leak under high temperature or overuse. If the leakage contaminates the machine parts, please clean these parts and replace the contaminated parts if necessary, the leaking battery should not be used again. If the leakage is accidentally stuck on the skin, clean it with soap first, and then with lemon juice or vinegar; if the leakage accidentally touches the eyes, clean it with water immediately and go to the hospital for examination and treatment immediately. The liquid spilled from the battery pack can corrode or burn.
15. The battery pack needs to be protected from moisture and mildew. Water or rain is prohibited.
16. If the battery is not used for a long time, please charge and discharge it once every 2 months and store it fully again.
17. The ambient temperature range of the battery pack is 0-45℃. The battery pack capacity will be affected if the ambient temperature is too high or too low when the battery pack is stored.
18. Battery pack is lithium ion active material, the lithium ion activity is not consistent in different temperatures, the length of use in winter will be shortened.
19. Avoid placing the battery pack near other metal objects, such as paper, coins, keys, nails, screws, or other small metal parts, etc., because metal objects can cause the battery pack to be connected by electric shock. When the battery pack is short-circuited, it can cause sparks, burns, or explosive fires, etc.
20. Please do not dispose of discarded battery packs in general household garbage, flames or water.
21. Please collect damaged battery packs and take them to a recycling disposal center for disposal or dispose of them in an environmentally friendly manner.
22. Please do not charge the battery when the room temperature is below 10℃ or above 50℃; it may not be charged when the room temperature is below 0℃.
23. When charging, it is strictly forbidden to place the battery pack charger on a flammable object such as a bed sofa, and try to place it on a tile floor, concrete floor and other objects.
24. When charging, please ask someone to supervise the charger, and overcharging is strictly prohibited.

Rechargeable electric chain saw information description

Please refer to follow this instruction manual for safety instructions, operating procedures and warranty. Keep the instructions and original sales data in a dry place for future reference.
Warning: Read the operating instructions carefully before use, and familiarize the user with the functions and basic operation of the product. Use and maintain the product in accordance with the instructions to ensure proper operation. The product manual should be kept near the product.

Tips for maintaining maximum battery life

1. Charge the battery pack in time before it is completely depleted. Stop tool operation and charge the battery pack when you find the tool is low on power.
2. Do not re-charge a fully charged battery pack. Overcharging will shorten the life of the battery.
3. Please charge the battery pack at a room temperature of 10°C-40°C (50°F-104°F). Please charge the battery pack after it has cooled down from the scorching heat.。

Keep all warnings and instructions for reference.

1. Familiarize yourself with the controls and the proper way to operate the unit.
2. The cutting parts will continue to rotate even after the motor is turned off.
3. Do not allow children or persons unfamiliar with these instructions to use the machine. Local regulations may restrict the age of the operator.
4. Do not use the machine with people (especially children) or pets nearby.
5. Use the machine only in well-lit or well-lit conditions. Avoid using the machine in bad weather, especially in lightning conditions.
6. Check for wear or damage before using the machine or after the machine has been hit, and repair if necessary.
7. Be careful not to get scratched by the mower equipment. After replacing the cutting line with a new one, be sure to return it to its normal operating position before turning on the equipment.
8. Do not install metal cutting parts.
9. This equipment should not be used by persons (including children) who are unfamiliar with the operating instructions and by persons who are physically, mentally and emotionally unsound or lack experience and knowledge, unless they are supervised and instructed in its use by a person responsible for their safety. Children should be supervised and not allowed to play with this tool.
10. Exercise extreme caution when using the tool.
11. Operate the tool only when in good physical condition. Perform all operations calmly and carefully. Use common sense when operating and always remember that the operator or user is responsible for any damage caused to others and their property.
12. Never operate the tool when tired, unwell or under the influence of alcohol or drugs.
13. If the tool shows signs of operational failure, turn it off immediately.
14. Keep your fingers away from the switch trigger when not operating the tool and
15. when moving between operating positions.
    Tool Usage
    Use the right tool. Rechargeable lawn trimmers are intended for cutting grass and tussocks only. It should not be used for other purposes, such as hedge cutting, as this may cause personal injury.

Personal Protection Equipment

1. Pay attention to clothing. Dress should be practical and appropriate, e.g., you should wear clothing that is tight fitting but does not interfere with operation. Do not wear jewelry or clothing that may become entangled with grass. Wear a protective headgear to protect long hair.
2. When using tools, always wear sturdy boots with non-slip soles. This will prevent injury and ensure a firm footing.
3. Always wear goggles when using power tools to avoid eye injury. Goggles must meet the requirements of ANSI Z87.1 in the USA, EN 166 in Europe or AS/NZS 1336 in Australia/New  Zealand. In Australia/New Zealand, a face shield is required by law to protect the face.It is the employer’s responsibility to monitor that tool operators and other near-work area personnel wear appropriate safety protective equipment.

LITHIUM MOWER SPECIFICATIONS

• The manufacturer reserves the right to change specifications without notice.
• Specifications and battery packs may vary depending on the country to which they are sold.
• The weight varies depending on the accessories (including the battery pack). According to the combination of the heaviest and lightest EPTA-Procedure 01/2014 See table.

Symbols

The following shows the symbols used in this tool. Please be sure to understand the meaning before using the tool.

recommended.
| Do not expose to moisture.
| Do not use metal blades.
Ni-MH
Li-ion| EU countries only
Do not dispose of electrical equipment or battery packs together with ordinary household waste!Be sure to comply with the European directives on waste electrical and electronic equipment, batteries and accumulators, and waste batteries and accumulators and enforce them in accordance with laws and regulations. Electrical equipment and battery packs that have reached the end of their useful life must be sorted and recycled to recycling facilities that
comply with environmental protection regulations.

Safety Warning

Important Safety Precautions

Warning：
Read all warnings and all instructions. Failure to follow the warnings and instructions below can result in electric shock, fire, and/or serious injury.

LITHIUM MOWER STRUCTURE SCHEMATIC

LITHIUM MOWER DETAILS

Model| AG2603
1| Automatic Trigger
2| Self-locking push knob
3| Speed control / display
4| Battery Pack
5| Plum lock handle
6| Adjustment handle
7| Rear section working rod
8| Tube-locking knob
9| Lock Knob
10| Fixed pin
11| Front section working rod
12| Head – Adjustment Knob
13| Rope work head
14| Protective Cover
15| Blade
16| Blade work head
17| Saw blade work head

LITHIUM MOWER INSTALLATION GUIDE

The working rod link is installed as shown in the figure on the right:

1. lifting knob turn half a turn, so that the cylindrical pin in the tube to avoid empty;
2. Insert the front working rod along the direction of the cylindrical pin, into the link tube and inserted to the end, Figure 1 cylindrical rotation reset, micro-movement of the front working tube to hear the sound of ‘click’ after the cylindrical pin and inserted into the front working rod hole, to this front and rear working tube can not be turned and confirmed in place;
3. Then lock the side lock button, the link is complete.

Attention：
Be sure to turn off the power to the tool and remove the battery pack before performing any assembly operations on the tool to avoid accidental start-ups that could result in serious personal injury.

1. Adjustment handle
2. External hexagonal nut
3. Plum locking handle

Mounting handle as shown on the left:
As shown on the left, put the front handle Figure 1 on the front housing handle seat and put the hexagonal nut Figure 2 into the hexagonal slot of the front handle, at this time the plum screw Figure 3 through the hole and the hexagonal nut lock, clockwise rotation of the plum handle and the nut lock fixed.
Attention：
The front handle can be easily mounted on the housing handle base by using the horizontal cutout in the mounting position.

1. M4 nuts-2PCS
2. Guard assembly
3. M4X20 screw-2PCS

Install the grass head as shown in the picture on the right:

1. Install the inner platen upward in the axial direction as shown in the figure on the right, and fit the teeth of the inner platen with the shaft teeth;
2. Insert the hexagonal wrench S5 into the hole of the inner pressure plate as shown in the figure on the right, (when inserting, rotate the inner pressure plate so that the hole of the inner pressure plate is aligned with the notch of the guard), so that its output can not be rotated;
3. Rotate the haying head tool counterclockwise as shown in Fig. 3, and lock it with the thread of the working shaft, then remove the accessory wrench.

Attention：
Installation of the inner pressure plate to be stuck fixed and hit the grass head installation is counterclockwise rotation.

Install the shield as shown in the picture on the left:

1. Check whether the two M4 nuts in the head position figure 1 are off or positioned at the bottom as shown in the left figure, or adjust in place if the side;
2. As shown in the direction of the left figure to install the shield assembly extended axial direction to the head position, left and right micro-movement adjustment, so that the shield assembly groove and the raised position of the head corresponding, check the shield screw holes and the head of the M4 screw holes aligned on the good;
3. As in Figure 3 use the two M4 screws below to fix with the M4 nut inside the head, tighten the two M4 screws period locking fixed can be.

Attention：
The wire is installed in the outward direction during installation.

1. Inner pressure plate
2. Accessories-S5 wrench
3. Weeding working head

FUNCTION DESCRIPTION

1. Working rod
2. Swivel handle

The front handle adjustment is shown on the right:

1. Rotating the plum handle and loosening the locking bolt;
2. The front handle can be adjusted from 0 to 180 degrees, and can be adjusted back and forth according to the comfort of the operation; rotate the plum handle to lock and fix it after adjustment.

Warning：
Please remove the battery pack from the mower before adjusting the working shaft length to avoid personal injury.
Telescopic working rod as shown on the left:
To adjust the working shaft length turn the handle counterclockwise to the working lever unlocked position and then push and pull the working lever to the desired length.

Warning：
– When mowing on slopes, be sure to watch out for rocks and other foreign objects thrown from the mowing head area.
– Be sure to keep a firm footing when mowing on slopes.

1. Lock button

The safety self-locking structure is shown in the figure on the right:
To avoid users from accidentally pulling the switch trigger, this tool uses a self-locking push button.
To start the tool, push the self-locking knob first, then pull the switch trigger. Release the switch trigger to stop the tool.

Head angle adjustment as shown on the left:
To ease the difficulty of working in narrow spaces with restricted height, such as mowing grass under outdoor wooden cleats and similar operations, the mowing head can be bent down after pressing the lock button so that the working rod operates parallel to the ground, and personnel can also adjust the angle of the mowing head in this way to mow grass on slopes.

1. Downward pressure on the lock button, the working rod can be adjusted in height;
2. According to the height or site height, choose the right angle of the working rod.

• Head adjustment angle: 0 to 60 degrees

1. Self-locking push button
2. Switch trigger

The display functions as shown on the left:

• Power display provides power consumption.
• Different working requirements to choose high and low speed, use ‘gear button’ (turtle means low speed gear, hare means high speed gear).
• With reversing self-stop function, when the working head is entangled by grass, you can choose reversing back function, choose reversing times according to the entangling situation, use ‘rotary switch button’.

WORKING HEAD INSTALLATION SWITCHING FUNCTION DESCRIPTION

Two-blade working head

1. Accessory tool
2. Inner pressure plate
3. Two leaf one blade
4. External pressure plate
5. Protective cover
6. External hexagonal lock nut

8 inch saw blade work head

1. Accessory tool
2. Inner pressure plate
3. 8 inch saw blade
4. External pressure plate
5. Protective cover
6. External hexagonal lock nut

OPERATING INSTRUCTIONS

The shoulder straps are fixed as shown on the right.:
Hook the shoulder strap into the hole on the front handle, and adjust the length of the strap according to the working comfort.

1. shoulder strap
2. Hooks

Attention ：

• Do not let the spool touch the ground when using the mower. The spool touching the ground may cause damage to the mower by overloading the motor, and also damage the mowing rope.

• Never attempt to mow tall grass from the roots in one pass and never use the mower in overly dense grass. Mowing tall grass near the roots in one pass may cause the mower motor spindle to become entangled in the grass, causing motor overload and eventual damage to the mower.
  Startup Tools

• Ensure that no children or other persons are within 15m (50 feet) of the work area and that the work area is free of any other animals. Otherwise, stop using the tool.

USE THIS TOOL AS A TRIMMER

• To use the tool for edging purposes, hold the mower’s working lever in one hand and turn the handle counterclockwise to loosen the working lever, rotate the working lever and motor housing together 180 degrees, and tighten the handle clockwise until the handle locks.
  Attention：

• Make full use of the telescopic length before rotating the working rod

•  Be sure to lock the motor housing and working rod after changing to trimming status

• When mowing grass, move the mower around the tree or brick so that the nylon cord or blade does not come in contact with the tree or brick. It is recommended to keep the tool at least 5 cm away from the tree or brick. If the nylon cord or blades come in contact with trees or bricks, the nylon cord may break and the blades may wear out quickly. If the nylon rope breaks in the spool, reinstall the nylon rope from the attachment.

Maintenance

Warning：

• Before checking or servicing the tool, be sure to turn off the power to the tool and remove the battery pack. Failure to turn off the power and remove the battery pack may result in accidental start-up, leading to serious personal injury.
  Attention：
  Do not use gasoline, benzene, thinner, alcohol or similar substances to clean the tools. Otherwise, it may cause discoloration of the tool, deformation of the goods and cracks.

Warranty Terms

♦ Warranty period.

• Under normal use, within 6 months from the date of purchase, and rotor commutator wear less than 0.1mm on one side, indeed, due to quality reasons caused by product failure belongs to the warranty; lithium products lithium battery 6 months free
  replacement new.

• Users must present the purchase receipt and warranty card when requesting warranty, and verified by the authorized maintenance center, otherwise the warranty does not have the right.
  ♦ Second, during the warranty period, the following cases are not covered by the warranty.

• Any parts that are naturally worn out in normal use, such as carbon brushes, seals, etc.

• Randomly attached accessories and fittings, such as collets, drills, etc.

•  Damage caused by man-made reasons such as overload work or improper use.

• Damage caused by not using original Dexia spare parts and accessories as required.

• Damage caused by self disassembly, or repair, modification or maintenance in non-authorized repair points.

• Damage caused by improper transportation after sale.
  ♦ The Company reserves the right to modify the above provisions and has the final right of interpretation without violating the relevant national regulations.

Thank you for purchasing our products. Please read the product manual carefully before use, if you have any questions in using our items please do not hesitate to contact us. We are willing to provide you with a satisfactory solution.
Email: yaguilee@126.com
Please include your name and order number so we can better assist you. Our professional service team will reply you within 24 hours.

Warranty Card
Reply Line
Please fill in the form and send it back to
IMPORTANT: To ensure that your power tool is covered by the free warranty, please fill out the form below and send it back within one month,
User Name ……………   Company Name …………..
Age •  20  •  20-29  • 30-39  • 40-49  •  50
Nature ofuser  • Company Users •  Personal Users Career • Woodworking  • Metalwork •  Concretework  •  Decoration •  Hardware •  Hydroelectric Engineering • Other
Address……………….
Zipcode…………………………………………
E-mail …………………………………
Landline………………………………………..
Mobile Phone……………………………….
Model ……………………………………………
Fuselage number…………………………….
Purchase Date …………………………………
Invoice number …………………………….
DealerName……………………………………..
Dealer Address …………………………………
DealerPhone ……………………………………..
Stamp ………………………………………….

IF YOU HAVE ANY QUESTIONS ABOUT
KTYU’S PRODUCT, PLEASE CONTACT US!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>