IRIS HMD-U25 Top Fill Ultrasonic Air Humidifier Instruction Manual

IRIS HMD-U25 Top Fill Ultrasonic Air Humidifier Instruction Manual

IMPORTANT SAFEGUARDS

Prior to use, read the safety precautions carefully to ensure proper use. The precautions listed here are described under classification of Warnings and Cautions, and are intended to prevent harm or damages to users and other persons. All of these precautions are critical in terms of safety. Follow them at all times.

Graphic symbol indications: Indicates content that could lead to death or injury if handled incorrectly.

Avoid fire hazard.

• Do not use the humidifier outside. Failure to do so may result in electric shock, burn(s) or injury.
• Do not spray the humidifier (insecticides, hair products, grease and etc.)
• Do not use the humidifier near flammable substances (kerosene, gasoline, paint thinner, etc.), objects with sparks (cigarettes, incense, etc.) or flammable dust.
• Do not use the humidifier in or near a place where soot is generated. Otherwise, it may cause fire.
• Keep away from sources which could cause combustion or flames, (cigarettes, incense, etc). Failure to do so may cause fire.
• Do not sit or stand on, lean against or put goods on the humidifier.
• Unplug the AC adapter from the socket after using the humidifier.

Use the AC adapter correctly.

• Periodically remove the dust from the AC adapter. Accumulated dust may cause fire or electric shock due to insulation failures with humidity. Insert the AC adapter tightly into the socket. Failure to do so may cause fire or electric shock due to short circuiting.
• Make sure to unplug the AC adapter from the socket before performing maintenance, inspection or while moving the unit. Failure to do so may result in electric shock or injury.
• Do not plug or unplug the AC adapter with wet hands. Failure to do so may result in electric shock, burns or injury.
• The product cannot be used for anything other than 120 V~.
• The product cannot be used in foreign countries. Failure to do so may cause fire or electric shock. This product can only be used in the USA and Canada. Do not operate the humidifier overseas as the voltage will differ.
• Do not pull the AC adapter cord. Do not damage, forcefully bend, pull, twist, put heavy goods on or tuck the power cord. Failure to do so may damage the cord and cause fire or electric shock.
• Do not forcefully pull the cord to remove the AC adapter from the socket. Hold the AC adapter to remove it. Pulling the cord forcefully may damage it and cause fire  or electric shock.
• Stop using the humidifier when the AC adapter cord or the plug is damaged or loosely plugged in. Failure to do so may cause fire or electric shock due to short  circuiting. If the AC adapter is damaged, contact the shop where you purchased the product or return to IRIS USA, Inc.
• Do not allow young children to lick the AC adapter. It may cause injury or electric shock.
• Do not use other AC adapters from the one attached. Failure to do so may cause fire or electric shock. The attached AC adapter can be used only for this humidifier.

Setup placement.

• When placing the humidifier, make sure that it is not too close to walls, furniture, curtains and etc. Water condensation or minerals could damage electric goods.
• Place the humidifier on a flat stand (keeping the floor from getting wet) or a stable surface where it will not fall over.
• Place the Water tank and the Tank cover properly.

Water usage.

• Change water every day. Wash the Water tank every day to keep clean. Using old water may produce a unpleasant smell or may be bad for health.
• Make sure to throw away the remaining water in the Water tank or the body of the unit if the water is not used for a week or more.
• Throw out the water in the Water tank and the body of the unit when the water is almost frozen. Failure to do so may deface the surrounding area due to malfunction or a water leakage.

Do not move the humidifier with water in the Water tank.

• Moving the humidifier with water in the Water tank or the body of the unit may cause water leakage and make the floor wet when tilting it. When moving the humidifier, throw out the water in the Water tank and the body of the unit.
• Do not let the product fall upside-down. It may cause water leakage or fire. If the humidifier falls over and water leakage occurs, dry the wet area and make sure that it is stable and safe before using again. If it is still not fixed, contact IRIS USA, Inc. Customer Service.
• Lift from the bottom of the body when moving the humidifier.

Disassembly prohibited.

• Do not disassemble, repair, or modify. Doing so can cause fire, electric shock, or injury.
• Repair by persons other than trained repair technicians can be dangerous.
• Warning: To reduce the risk of fire or electric shock, do not use this product with any solid-state speed control device.

Abnormalities and malfunctions can cause smoke, fire, or electric shock.

Stop use immediately, cut power, and unplug from the electrical outlet when abnormalities or malfunctions occur. Examples of Abnormalities Abnormal sounds or odors.

• AC adapter become abnormally hot.

• Loss of power, etc. when power cord is moved.

• The product periodically stops during operation.

• Tingling sensation from electric current felt when the product is touched.

• Stop use and contact IRIS USA, Inc. customer service at 1-800-320-4747.

• Do not place the humidifier in a location with direct sunlight. Failure to do so may lead to deformation, discoloration or malfunction.
  

• Do not clean the humidifier with benzine, thinners, etc. Unit may get damaged or malfunction.

• Do not operate the humidifier around a radio or TV. Otherwise the electromagnetic interference may affect the normal operation of the product.

• Do not place the humidifier near magnetic devices such as speakers or IH cooking devices (electromagnetic cooking devices). Unit may not work properly.
  

Environment for using the humidifier

• Set the room temperature at 41-95 °F/5-35 °C. Low room temperature may make the floor wet and produce water condensation. Use the power button to adjust the humidity level or raise the room temperature. Periodically remove water condensation on walls, near windows or etc. Minerals in tap water on furniture or TV may dry and become white powder. The powder poses no harm. Use a towel, etc. to remove it.
• Excessive humidification may make the floor wet or cause water condensation. This product cannot adjust the humidity automatically. Adjust the humidity level frequently in accordance with the room temperature.
  

PARTS

Main unit

PREPARATION

Fill up Water tank with tap water

1. Remove the Tank cover.
2. Do not fill water above the Max Water Level.
3. • Make sure to remove the Tank cover when filling with water.

  * Two ways of filling up.  

2.  **Do not remove the Water tank.**  

→ Use a cup, etc. to fill water.

3.     4.  **Remove the Water tank.**  

→  Directly fill water from faucet.

  * Do not directly fill the main unit from the faucet. If filling, make sure to throw out the excess water.  

3. Place the Tank cover.
   Put the Tank cover and Mist outlet together to place them properly.

   •   * Failure to do so may form water in the Tank cover.

   • Once the Water tank is in the main unit it will start to humidify.

Caution

• Make sure to use tap water. Do not use water at 104 °F/40 °C or above, polluted water, mineral water, alkaline ionized water, well water etc.
• Do not add chemicals, spices or essential oil, etc. Failure to do so may propagate fungus or various germs, deform, crack or discolor the humidifier and cause water leakage or deface the surrounding area.

1. Plug the AC adapter into the Plug insert in the back.
   

2. Insert the AC adapter into the socket.
   The Indicator light will turn red when the unit is plugged in.

   • When the light is red, push the Control button to turn the unit on. After 40 seconds of the red light illuminating, the light will turn off if the button has not been pressed.

3. Press the Control button.
   Operation starts. Each time the Control button is pressed, it switches the humidity level and the brightness of the Indicator light.
   

   • After selecting the mode (low, medium, high), the Indicator light will turn off after 40 seconds. To switch to a different mode press the Control button twice.

If the Indicator light blinks in red

• If the Water tank becomes empty during operation, the humidifier stops operation and the Indicator light blinks in red twice. If no action is taken, the Indicator light blinks in red eight times and then the humidifier automatically turns off. When filling water in the Water tank, the humidifier will resume operation in the previously selected operation mode.

• If the Water tank is removed from the main unit during operation, the humidifier will stop operation and blink in red twice. Once the Water tank is inserted, operation will resume.

• If the depleted Water tank sensor is activated, the Indicator light blinks in red three times. If no action is taken, the Indicator light blinks seven times and then the humidifier automatically turns off. First check to see if there is water still in the Water tank. If there is, remove the AC adapter from the socket and insert it again.

• When moving the Water tank, make sure not to spill water. Remove the waterdrops on the Water tank.

• After Water tank is refilled, when pressing the Control button the Indicator light may blink in red, check whether the Float plate is set properly. (→ P10)

Caution

Make sure to turn off the power before removing the Tank cover from the main unit. Failure to do so may splash water into the air.

After using it
Refer to “Cleaning and maintenance” (→ P9-12) to clean the humidifier.

When the humidifier is not used for a long time
Unplug the AC adapter and store the humidifier in its original box.

CLEANING AND MAINTAINANCE

Caution

• Before cleaning, turn off the power and unplug the AC adapter from the socket.
• Do not plug/unplug the AC adapter with wet hands.
• Do not use thinner, benzine, stronger acid, alkaline detergents, bleaching agents and etc.

Water tank/main unit every time it is used

1. Remove the Tank cover, hold the Water tank handle to pull out the Water tank.
   Remove the waterdrops at bottom of the Water tank.

2. . Throw out the remaining water in the Water tank and main unit.
   When throwing out the water in main unit, make sure that the Control button and the Plug insert do not get wet.

   • Remove water on main unit.

3. Wash the Water tank in running water.
   Dismantle the Tank cover and wash each part.

   • How to dismantle the Tank cover.
     → Press on the long tabs on the inside of the Tank cover.

4. Place the Water tank/Tank cover back into place.
   

Main unit once every two week

1. Remove the Tank cover and then remove the Water tank from main unit.

2. Throw out the remaining water in the Water tank and main unit.

3. Wash it in water.

   • Use a soft sponge, etc. to wash the main unit to prevent it from getting wet.

   • Remove the Float plate and wash it in water or aqueous solution.(→ P11)

   • After placing the Float plate, check whether it moves smoothly.

   • • Use a soft brush or a cotton swab, etc. to clean the Water level sensor and the Ultrasonic transducer.

   • Stained Ultrasonic transducer or dusty Ultrasonic transducer may lower the humidity level or produce no humidity.

4. Use a soft cloth to clean.

   • Dry unit after done cleaning.

Filter/Water valve
Filter: According to the stained state
Water valve: Once per month

1. Remove the Tank cover and then remove the Water tank from main unit.
2. Throw out the remaining water in the Water tank.

• Remove the Filter in the Water tank according to the stained state.
  Press both sides of the Filter to remove it.
  

• Flip over the Water tank and remove the Water valve from the bottom.
  Turn the Water valve in a counter-clockwise direction to remove it.

• Wash Filter/Water valve.
  Wash in water or soak in it Citric acid aqueous for 5-10 minutes and then rinse it in fresh water a couple of times.

• Insert Filter/Water valve.
  Turn the Water valve in a clockwise direction (at the bottom of the Water tank) and place the Filter Inside (Water tank).
  *Inserting loosely may cause water leakage.

Activated Charcoal filter periodically

If the activated Charcoal filter has been clogged with dust, the air may not be humidified. The humidifier may be clogged with dust. Brush it away or use a cleaner to remove it.

How to make Citric acid aqueous

Add Citric acid aqueous: in water or lukewarm water (104 °F/40 °C or below) with the following ratio and dissolve it well.

• Citric acid aqueous: add 20 grams of citric acid (or two level tablespoonfuls of citric acid) per 3 liters of water.
  The high density may damage the humidifier.

Caution

• Before cleaning always turn power off and unplug the unit from outlet.
• Do not rinse body of unit under faucet. To clean, wipe the body of unit with a paper towel.
• Do not use any solvents or aggressive cleaning agents. Keep water away from the Mist outlet.
• Do not tamper with the Water Sensor.

About White Dust

Use of high-mineral content water may cause a white mineral residue to accumulate on room surfaces near the humidifier. The mineral residue is commonly referred to as “White Dust”. The higher the mineral content (the harder your water is), the greater the potential for White Dust. The White Dust is not caused by a defect in the humidifier, but is due only to minerals suspended in the water from your tap.

Caution

• If you have hard tap water STOP using tap water and use ONLY Filtered, distilled, cold boiled or bottled water to minimize the White Dust residue.

White Dust Cleaning

1. If mineral deposits (“White Dust”) are evident around the Ultrasonic transducer and Water level sensor, clean these surfaces with a soft cloth and a small amount of undiluted white vinegar.
2. If necessary, mix a solution of 50% white vinegar and 50% water and fill the body with enough solution to cover the Ultrasonic transducer.
3. Allow it to soak for an hour and then use a toothbrush, etc. to gently loosen buildup on the Ultrasonic transducer.
4. Put 1 cup of water in the body and wipe clean with a soft cloth.

Caution

When emptying the Water tank of unit, make sure that the water is poured away from the Mist outlet. If water is poured into the outlet it may damage the humidifier.

TROUBLESHOOTING

Before making repairs, read the following content carefully to fix common problems.

Insert the AC adapter into the socket securely.
The power cord of the AC adapter has not been plugged into the socket securely| Make sure to securely insert the AC adapter into the Plug insert.
Poor humidification
(Indicator light blinks in red twice)| The Water tank has been empty| Fill Water tank with water.
The Water tank has been removed from main unit| Place the Water tank in main unit
The Float plate has not been placed| Place the Float plate back in properly.
Poor humidification
(Indicator light blinks in red three times)| Depleted Water tank sensor has been activated| Disconnect the AC adapter from the socket and connect it again.
Low mist| The humidifier has been placed on a thick carpet| Place the humidifier on a flat stand.
The Ultrasonic transducer has been stained (mineral deposits or dust is formed on the transducer)| Use a soft brush or a cotton swab to clean the Ultrasonic transducer.
The filter has been clogged with dust| Clean the filter.
The activated Charcoal filter has been clogged with dust| Remove the dust in the activated Charcoal filter.
Low humidity| The room is beyond its coverage area| Use the humidifier within its coverage area.
Windows and doors are open| Close the windows and doors when using the humidifier.
Wet floor| Low room temperature| Low room temperature may make the floor wet. Use the humidifier with heaters and other devices.
The humidifier has been placed on the floor| Placing the humidifier on the floor directly may make the floor wet. Place the humidifier on a flat, stable stand, etc.
| Inside the main unit or Inside water tank) may be stained| Clean the main unit and the Water tank periodically.

If the problem persists, contact IRIS USA, Inc. Customer Service Department or a qualified professional.

Warning: Do not disassemble, repair or modify the product yourself. Any other servicing should be performed by any authorized service representative.

SPECIFICATIONS

AC adapter

POWER ON: AC 100-240 V, 50/60 Hz, 0.6 A
AC 100-240 V, 50/60 Hz, 0.6 A: DC24 V. 1.0 A
OUTPUT: 70.9 in/1.8 m

• Specifications are subject to change without prior notice.
• For the continuous humidification by the maximum humidification level, the coverage area is not a guaranteed performance.

MANUFACTURER 1-YEAR WARRANTY

THE MANUFACTURER WARRANTS

IRIS USA, Inc. products are to be free from defects in material and workmanship under normal non-commercial, household use, when operated and cared for in accordance with the Manufacturer’s written instructions provided.

THE 1-YEAR WARRANTY (“WARRANTY”) DOES NOT COVER

Any damage caused by accident, misuse, or abuse, including without limitation, damage caused by use in a humid area, improper cleaning, neglect, alteration, fire, theft, non-recommended temperature use and does not apply to minor imperfections, scratches, stains, discoloration, surface markings as a result of shipping or other damage to external or internal surfaces which does not impair the utility and/or functionality of the product.

TO OBTAIN SERVICE

If service should be necessary, you should contact IRIS USA, Inc. Customer Service (“Customer Service”) at 1-800-320-4747. You may then return the properly packaged product(s). (using adequate packing and shipping material to prevent damage in transit), with postage prepaid along with name, address, telephone number, model number, and proof of date of purchase (a copy of the receipt) and a detailed description of the claimed defect. This warranty shall not cover any damage incurred to the products during transit to Customer Service. You shall have the obligation and responsibility to: pay for all services and parts not covered by the warranty.

MANUFACTURER’S OBLIGATION

The Warranty may not be altered, expanded, extended, revised or varied except by written instrument executed by the Manufacturer.

THE MANUFACTURER’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT(S) AT THE MANUFACTURER’S SOLE AND EXCLUSIVE OPTION. THE MANUFACTURER WILL REPLACE ANY ITEM FOUND TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITH THE MOST COMPARABLE CURRENT ITEM. IRIS USA, INC. DOES NOT ACCEPT SPECIAL REQUESTS, NOR DO WE HAVE THE ABILITY TO UPGRADE IN EXCHANGE FOR MONEY. THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER DIRECT OR INDIRECT. THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE ARE MADE WITH RESPECT TO THE PRODUCTS.

Some states do not allow the exclusion of limitation of incidental or consequential damages, so the above limitation exclusions may not apply. This Warranty gives specific legal rights, and there may also be other rights which vary from state to state.

DISCONTINUED ITEM RETURNED

If the item returned is discontinued and is no longer available, IRIS USA, Inc. will automatically replace your item with the most
comparable item currently manufactured.

Attn: Customer Service (Returns Department) IRIS USA, Inc.
13423 West Cactus Road Surprise, AZ 85379
©2021 IRIS USA, Inc. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>