GOODUM D63 Door Locks with Handle Instruction Manual

: June 14, 2024
: GOODUM

Table of Contents

Read User Manual Online (PDF format)
Download This Manual (PDF format)

GOODUM D63 Door Locks with Handle Instruction Manual

z

Installation

(a) Drilling Hole

Mark on the door according to the drawin
Drill holes correspondingly with electro drill
Drill holes on the door frame with corresponding tools to install strike plate

(b) Installing latch and strike plate

Fix the lock on the door broadside with two screws
Fix the plastic bottom case and strike plate on the door frame with two screws

(C) Installing square shaft of front lock plate

Put the square shaft into square hole(on the front lock plate)
Fix the square shaft with pin bolt in components bag and then open it

(D) Installing front lock plate
Install front panel, the two screw pillars should be aligned with the holes of the latch, pull the connecting line of front panel to the back of the door, in order to connect them.

(E) Installation of connecting line and back lock plate

Open the battery cover
Connect connecting lines of the front and the back lock plates.
Fix the front and the back lock plates by 3 fixing screws.
Positioning the lock plate properly, tighten the 3 screws to fix lock plates

(F) Equipping batteries

Put 4 AA batteries into the battery case and pay attention to the directions.
Close the battery case and fix it with screws.
Installation finished.

(G) Test after installation

The door can be opened normally when pushing the handle.
After power on, the motor reverse, the handle will be idling when push it. Input the initial password to check door opening
Make sure the door can be opened normally by the mechanical key.

(I) Usage of emergency mechanical key

Take down the cylinder cover on front handle with plastic sucker
Insert the right mechanical key, turning 90 degrees.
Push the handle, door opened.

Left-right adjustment

Product Guide

Operation Instruction

Outline
Admin: code (remote controller and fingerprint can not be used as admin).
User:card , password and remote controller(optional).
User capacity: 1 admin code, 100 codes, 800 open door cards, 120 remote controllers(optional).
System initialization
Default admin code is “123456”. Please change the admin code after you install the lock to replace the default admin code（You can not add user with default admin code）.

You can also press “*” “#”, and then input the admin code to enter the system setting.

Operation

1 Register Master User

2 Add Normal User

3 Delete User (Single Master or Normal User)

4 Passage Mode

When the lock is required to unlock frequently, set the lock to passage mode can let the people unlock the lock without any identification.

5 Unlocking Mode

Sometimes it you need a higher security level you can set up the lock in double unlocking mode, which the unlock needs 3 registered users for unlocking each time.

6 Unlock voice Settings

7 instructions

Admin User can set a new Admin code by revision. After the revision,
the new Admin user will replace the old one .
(the new Admin code will replace the old one)
When entering the Passage Mode, the motor will not lock the door automatically after unlocking by fingerprint/code/remote controller, and everyone can unlock the door by turning the handle. Press # to cancel the Passage Mode.
While inputting the password, please press # for confirmation, and press * for elimination.
This lock has anti-peeking function, with which users can input innocent number before or after the password, e.g. XXX+password+XXX.
(no more than 20 digits.)
If you do not add any remote controllers, the remote control mode turns off which saves power. It will not work until you add the remote controller.
Upon add users, input password and press “#” to confirm it,the password and fingerprint couldn’t input same, the password digits is 6-10 digits.
The keypad will be locked for 3 minutes after a continuous inputting wrong password for 5 times.
Low voltage alarm function： While the batteries lower than 4.8V, the lock will alarm, please change the batteries. The lock can be unlocked 200 times.
In the double users mode, any two groups of different unlocking information are combined to unlock, and the system will automatically exit if there is no operation for more than 10 seconds after each operation.