DEFAINT 1000 000 000 Smart Home Alarm System Kit User Manual
- June 14, 2024
- DEFAINT
Table of Contents
1000 000 000 Smart Home Alarm System Kit
Product Information – Smart Home Alarm System
Item #1000 000 000
User Guide
SMART HOME ALARM SYSTEM
Thank you for choosing the Defiant Smart Home Alarm System Kit.
This product is designed to enhance your home security. Please read
the following information and instructions carefully before
installation and usage.
Table of Contents
- Safety Information
- Warranty
- Pre-Installation
- Inspect All Components
- About Wireless Equipment
- Installation Location
- Package Contents
- Product Introduction
- Siren Hub
- Keypad
- Motion Sensor
- Door/Window Sensor
- Installation
- Operation
- Replace the Batteries
- Specification
- Troubleshooting
Safety Information
-
Keep out of reach of children. This product contains small
magnets and other small parts, which can cause choking or injury if
ingested. -
Do not use different brands of batteries in the same
device. -
When replacing batteries, always replace the whole set.
-
Do not use rechargeable or reusable batteries.
-
Do not allow children to install batteries unsupervised.
-
Follow battery manufacturer’s instructions for the proper
handling, storage, and disposal of batteries. -
Used batteries should be disposed of at an appropriate
recycling center. Do not discard with normal household trash. DO
NOT BURN. -
Before mounting any of the devices, clean the surface with a
gentle degreaser. Please note that some surfaces may be unsuitable
for mounting with the adhesive pads provided. -
Risk of personal injury. Prolonged exposure to alarm siren may
cause permanent hearing loss. -
Keep batteries away from children. This product contains
coin/button cell batteries. -
If the coin/button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead to death. Keep
away from infants and small children at all times. -
If the battery is swallowed or placed inside any part of the
body, immediately seek EMERGENCY medical attention. -
Battery may rupture if the incorrect type of battery is used.
Follow the instructions in this manual. -
Do not install in wet locations, outside the premises
(outdoors), near metal objects or mirrors which may cause radio
signal interference, or near main wiring.
Warranty
This product is guaranteed to be free of defects in materials
and workmanship for 1 year from the date of purchase. Guarantee
does not include normal wear and tear.
Pre-Installation
Inspect All Components
Compare all parts in the package with the Package Contents list.
If any part appears missing or damaged, do not install this
product. Contact customer support.
If you need further assistance, please contact 877-592-5233">1-877-592-5233.
Item #1000 000 000
USER GUIDE
SMART HOME ALARM SYSTEM
THANK YOU We appreciate the trust and confidence you have placed in Defiant
through the purchase of our Smart Home Alarm System Kit. We strive to
continually create quality products designed to enhance your home. Visit us
online to see our full line of products available for your home improvement
needs. Thank you for choosing Defiant!
Table of Contents
Safety Information…………………… 3 Warranty…………………………………. 4 Pre-
Installation……………………….. 5
Inspect All Components…………. 5 About Wireless Equipment …….. 5 Installation
Location ……………… 5 Package Contents ………………… 6 Product Introduction ……………….. 7
Siren Hub…………………………….. 7
Keypad………………………………..10 Motion Sensor……………………..12 Door/Window Sensor…………….13 Installation …………………………….15 Operation ………………………………20 Replace the Batteries ……………..23 Specification …………………………. 24 Troubleshooting…………………….. 25
2
Safety Information
WARNING: Keep out of reach of children. This product contains small magnets
and other small parts, which can cause choking or injury if ingested.
WARNING: Any battery has the potential to leak harmful chemicals that can
damage skin, clothing or the inside of the battery compartment. To avoid risk
of injury, do not allow any substance leaked from the battery to come in
contact with eyes or skin. Any battery has the potential to rupture and may
even explode if exposed to fire or other forms of excessive heat. Use caution
at all times when handling batteries. To reduce the risk of personal injury or
harm to this product, take the following precautions:
Do not use different brands of batteries in the same device.
When replacing batteries always replace the whole set.
Do not use rechargeable or reusable batteries.
Do not allow children to install batteries unsupervised.
Follow battery manufacturer’s instructions for the proper handling, storage
and disposal of batteries.
WARNING: Used batteries should be disposed of at an appropriate recycling
center. Do not discard with normal household trash. DO NOT BURN.
WARNING: Before mounting any of the devices clean the surface with a gentle
degreaser. Please note that some surfaces may be unsuitable for mounting with
the adhesive pads provided.
WARNING: Risk of personal injury. Prolonged exposure to alarm siren may cause
permanent hearing loss.
WARNING: Keep batteries away from children. This product contains coin/button
cell batteries.
If the coin/button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death. Keep away from infants and small
children at all times.
If battery is swallowed or placed inside any part of the body, immediately
seek EMERGENCY medical attention.
Battery may rupture if the inczorrect type of battery is used. Follow the
instructions in this manual.
CAUTION: Do not install In wet locations. Outside the premises (outdoors).
Near metal objects or mirrors which
may cause radio signal interference. Near main wiring.
3
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Warranty
1 YEAR LIMITED WARRANTY This product is guaranteed to be free of defects in
materials and workmanship for 1 year from the date of purchase. Guarantee does
not include normal wear and tear.
Wireless Protocal
The Wi-Fi CERTIFIEDTM Logo is a registered trademark of Wi-Fi Alliance®. The
Bluetooth word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. Apple and the Apple logos are trademarks of Apple, Inc., registered
in the U.S., and other countries. App Store is a service mark of Apple Inc.
Google, Google Play and Google Home are trademarks of Google LLC. The keypad
and the sensors only works with Siren Hub required.
FCC Regulation
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. FCC Caution:
Changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment. FCC
Statement: “This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: –Reorient or relocate
the receiving antenna. –Increase the separation between the equipment and
receiver. –Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. –Consult the dealer or an experienced
radio/TV technician for help.” This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the
radiator and any part of your body.
Pre-Installation
INSPECT ALL COMPONENTS
Compare all parts in the package with the Package Contents list. If any part
appears missing or damaged, do not install this product. Contact customer
support.
ABOUT WIRELESS EQUIPMENT Wireless systems are reliable and tested to high
standards; however, it is important to consider that there are some
limitations due to their transmitting power and range:
Receivers may be blocked by radio signals occurring on or near operating
frequencies, regardless of the code selected.
A receiver can only respond to one transmitted signal at a time. Wireless
equipment should be tested regularly to determine whether there are sources of
interference and to protect against faults.
INSTALLATION LOCATION
DETERMINE THE LOCATION OF THE SIREN HUB, WHICH SHOULD BE PLACED: Within a few
feet of an electrical outlet Where it is easily accessible Away from doors or
windows that could be accessed by intruders Away from extreme temperature
sources (radiators, ovens, stoves etc.) and large metal objects
that could interfere with the wireless performance.
5
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Pre-Installation
PACKAGE CONTENTS
AA
BB
CC
DD EE
Part Description
AA Siren Hub with 3*AA batteries
BB Keypad with 3*AA batteries
CC
Motion Sensor with 2*AAA batteries
DD Door/Window Sensors with CR2032 battery
EE Magnet
FF
Power Adapter and Cable
GG
Keypad Double-Side Adhesive Tape
HH Mounting Screws Sets
Quantity 1
1
1 2
2 1 1 10
FF
GG
HH
WARNING: THESE SENSORS AND THE KEYPAD HAVE TAMPER RESISTANT BRACKETS TO ENSURE THEY ARE NOT REMOVED FROM THEIR INSTALLATION PLACEMENT. THESE BRACKETS MUST REMAIN ON THE SENSORS DURING USE. REMOVAL OF THESE BRACKETS WILL RESULT IN A TAMPER ALARM BEING TRIGGERED.
6
Pre-Installation (continued)
Product Introduction Siren Hub Your home Siren Hub connects the alarm system
to your 2.4GHz Wireless network and other smart home devices. It also sounds
the alarm to alert you when a security breach has occurred.
A
B
CDE
F
Part Description A Siren B Alarm LED C Power LED D Internet LED E Join/Pairing LED
Part Description F Reset Button G Battery H Bracket I Power Adapter and Cable
G
H
I
7
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Pre-Installation (continued)
Power LED Internet LED Alarm LED
OFF
OFF
OFF
Join/Pairing Description LED
OFF
The base station is powered off.
BLINKING OFF
OFF
OFF
Booting up. Applicable whether the Unit
is onboarded or not.
ON
Blinking ON=
OFF
“GREEN” |
“YELLOW” |
“RED”
ON
OFF
ON=
OFF
“GREEN” |
“YELLOW” |
“RED”
ON
ON
OFF
OFF
ON
ON
Blinking OFF
Armed Away OFF ON= “RED” Armed Stay ON=”GREEN”
OFF
OFF
Connecting to WiFi. See the timeout below. Unit is Onboarded.
Failed to connect to WiFi. The unit did not connect to the Internet after 30
seconds. Unit is Onboarded.
Disarmed, powered on and operates normally. No Faults detected, no offline
sensors. Armed in Stay or Away Modes, Powered on operates normally. No Faults
detected, no offline sensors.
The Unit Reset. Press the siren button for 10 seconds to trigger a reset. The
LED will blink for 5 secs. The Unit will remove all paired sensors and keypad
and will clear any paired sensors, sensor states, and stored PINs.
8
Pre-Installation (continued)
Power LED Internet LED Alarm LED
ON
ON
OFF
ON
ON
ON
ON
OFF
ON= “YELLOW”
Join/Pairing Description LED
FAST BLINKING for 1 sec duration.
Pairing of a sensor failed.
ON solid for Pairing of a sensor succeeded. 1 sec duration.
OFF
Blue Alarm State. May happen when 1)
one or more sensors lose connectivity to the hub, which is indicated as an “offline”
state in the app. 2) the user tries to arm
the alarm system and some of the sensors
may need to be bypassed. The blue light goes off after the condition is rectified.
ON
ON
Blinking ON
Fast
OFF
Blinking
ON=RED OFF blinking
ON
OFF
ON
OFF
Turn on the alarm indicator LEDs if the alarm is active.
Unit is in battery backup mode.
Unit is in low battery mode. WiFi is disconnected.
9
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Pre-Installation (continued)
Keypad The keypad controls your alarm system via Bluetooth through connecting
to gateway. It features four alarm modes: “Disarm” – deactivates sensors, “Arm
Away” – activates all sensors, “Arm Stay” – activates select sensors and “SOS”
to active emergency alarm to suit your needs.
A
B
D
C
E
G
F
H
N
M
I
J
L
K
Part Description A Disarm B Arm Away C Arm Stay D SOS E Network Indicator F Not Ready Sensor Alert Indicator G Battery Indicator
Part Description H Buzzer I Cancel J Confirm K Anti-tamper Switch L Reset/Onboard Button M Battery N Bracket
Items Onboard Button
Description
Press and hold the reset/onboard button (behind the battery cover) for 5
seconds to start onboarding/pairing of the device. This is a medium duration
press.
10
Pre-Installation (continued)
Items Battery Indicator
Not Ready Sensor Alert Indicator
Network Indicator
Reset Button
Anti-tamper Switch Buzzer Confirm/Cancel
Disarmed Armed Stay
Armed Away SOS
Description
Solid green: Battery capacity >= 20% Solid yellow: Low 20% >=battery capacity
10% Solid red: Very Low Battery capacity <= 10% Batteries should be replaced
If some sensors are not ready (tampered with is active, malfunctioned sensor, bypass required) when try to arm the system, the app will send the notification and the LED indicator on the keypad will flash to indicate that the system is not ready for arming. Presses “” to continue arming or press “X” to cancel arming. Note that the sensor can be bypassed/ignored in the app before arming.
Flashing green: Pairing and searching for the hub Solid red: No signal or bad signal from the hub Solid green: Paired to the hub, good signal
Press and hold it for 10 seconds to reset the device. After reset, the device will clear the network information, restore factory Settings,and enter the pairing state.
Once the keypad is taken off the bracket, the anti-tamper alarm will be triggered
For sound prompt Confirm: Confirms the mode you are entering Cancels: Cancels whatever mode you may have been entering and resets the keypad back to a ready state
Disarmed: Disarms the alarm system. No alarms will sound in this mode Armed Stay: Used to only arm certain selected sensors when the user is at home but still wants partial protection. Ex. If you want to secure the front door, but do not want the hallway motion sensor activated Armed Away: Used to arm all sensors on the network
Holding the SOS button for 3 seconds triggers an alarm from the Siren Hub.
11
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Pre-Installation (continued)
Motion Sensor
The Motion Sensor sends you mobile alerts whenever motion is detected. It
seamlessly pairs with your Siren Hub and can be easily mounted to any wall or
corner in your home.
A
D B C
Part Description A LED Indicator B Reset/Onboard Button C Anti-tamper Switch D
Battery E Bracket
E
Items LED Indicator Reset Button
Onboard Button Anti-tamper Switch
Description
If sensor has not been added to Siren Hub, the LED will blink about once per
second. The LED will be turned off after connecting to the Siren Hub
Press and hold the reset button (behind the battery cover) for 10 seconds to
reset the device. The reset button is the same button used for onboarding.
After reset, the device will clear the network information, restore factory
Settings, and enter the pairing state.
Press and hold the reset/onboard button (behind the battery cover) for 5
seconds to start onboarding/pairing of the device. This is a medium duration
press.
If the sensor is removed from the bracket, it will trigger the anti-tamper
switch and send a notification to the app. When installing, please be sure
that the sensor is well mounted to avoid false notifications.
12
Pre-Installation (continued)
Door/Wndow Sensor Sends a notification or sounds the alarm whenever a door or
window is opened.
A
C
G B
D
F
E
Part Description A LED Indicator B Magnet C Anti-tamper Switch
Part Description D Battery E Battery Cover F Bracket G Bypass/Reset Button
Items LED Indicator Reset Button
Onboard Button
Description
If sensor has not been added to Siren Hub, the LED will blink about once per
second. The LED will be turned off after connecting to the Siren hub.
Press the front of the device for 10 seconds to reset the device. Note that
the bracket must be removed first. This is a long press. After reset, the
device will clear the network information, restore factory Settings, and enter
the pairing state. Immediately after reset, the sensor will provide updated
information including battery level to the hub.
Press the front of the device for 5 seconds to start onboarding/ pairing of
the device. Note that the Bracket(F) must be removed first.This is a medium
duration press.
13
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Pre-Installation (continued)
Items Bypass Button
Anti-tamper Switch
Description
Pressing the front of the device for < 1 second will temporarily disarm the
sensor (the default time is 1 minute(s). Then opening the door/window will not
trigger the alarm. The system will resume its state after the door/window has
been closed. A. By default, the bypass feature is disabled. If the door/
window is opened under ARM AWAY or ARM STAY state, the alarm will be
triggered. B. When the system is under ARM AWAY or ARM STAY mode, after you
set the BYPASS time, press the BYPASS button on t he device, the alarm will
not be triggered if the door/window is opened. C. The door/window needs to be
closed before the preset bypass time, otherwise the alarm will be triggered
again. D. The BYPASS feature only takes effect one time. If you closes the
door within the valid bypass time and opens it again, the alarm will be
triggered. E. If you triggers the door sensor first and then presses the
bypass button, the alarm will be triggered and must be turned off in the
keypad. F. After you press the bypass button, you must open the door or window
within 1 minute, otherwise this feature will not take effect.
If the sensor is removed from the bracket, it will trigger the anti-tamper
switch and send a notification to the app. When installing, please be sure
that the sensor is well mounted to avoid false notifications.
14
Installation
1 Mounting the Siren Hub
Plug the Power Cable (FF) into Siren Hub (AA) . Ensure Power Cable (FF) inside the wire duct.
IMPORTANT: Be sure that when choosing your location, that it
Can easily be seen when the strobe is flashing. You can hear the alarm. There
is a good 2.4GHz Wireless network. There is a wall socket nearby that is not
controlled by a wall switch.
The Siren Hub (AA) can be mounted on the wall or ceiling.
AA
FF Pull out the battery insulator pull tab to activate the battery.
AA
AA Remove the Bracket (H) from the Siren Hub (AA) by following the below arrow
direction.
AA H
Hang the Siren Hub (AA) on the Bracket (H) by following the direction of “UP” arrow on the back of Bracket (H) or following the opposite direction of the Open arrow on the front of Bracket (H).
Decide upon your placement position and attach the bracket with either Screws (HH) or preinstalled double-sided adhesive tape.
H
AA
Connect the Power Adapter (FF) to wall socket that is not controlled by a wall switch.
OR HH
FF
15
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Installation (continued)
2 Install the Keypad
IMPORTANT: Do not install the keypad:
Outdoors. Near large metal objects or mirrors as they sometimes cause radio
signal interference. Near main wiring.
Remove the Bracket (N) from the Keypad(BB) by following the direction of the
unlock marked on the side of Keypad (BB).
Pull out the battery insulator pull tab to activate the battery.
Hang the Keypad (BB) on the Bracket (N) by following the direction of lock
marked in the side of Keypad (BB).
Lock Unlock
N BB
Decide upon your placement position and attach the Bracket (N) with either
Screws (HH) or double-sided adhesive tape (GG).
OR
HH N
GG
N
BB
3 Installing the Motion Sensor
IMPORTANT:
Remove the clear, protective cover from the front of the motion sensor. The
sensor should be placed at a height of 6.5-8 ft. above the floor for best
coverage. There should be no large obstructions in front of the sensor. The
sensor should not be installed in locations where there may be wide
temperature changes such as near air conditioners, fans, refrigerators,or
ovens/ranges.
16
Installation (continued)
The Motion Sensor (CC) can be installed on the Decide upon your placement
position and top of a cabinet or other tall furniture, on the attach the
Bracket (E) with either Screws (HH) flat surface of a wall or in a corner wall
area. or preinstalled double-sided adhesive tape.
CC
CC
OR
CC
If installing on a horizontal surface, such as a tall piece of furniture or cabinet top, be sure to leave the mounting Bracket (E) in place on the back of the sensor so the anti-tampering alarm is not falsely triggered.
Proper Screws (HH) locations for wall-mount installation.
OR Remove the Bracket (E) from the Motion
Sensor (CC) by following the direction of the unlock marked on the side of
Motion Sensor (CC).
E CC
Unlock
17
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Installation (continued)
When placed on the top of cabinet or other tall furniture, be sure the face of
the sensor and the face of the furniture are flush with each other, as shown
in the illustration below. This will allow the signal to be uninterrupted and
maintain the best possible detection range.
Pull out the battery insulator pull tab to activate the battery. Hang the
Motion Sensor (CC) on the Bracket (E) by following the direction of lock
marked in the side of Motion Sensor (CC).
Lock
If mounted at a height of 7.4 ft. above the floor, the detection range will be
approximately 26 ft. with a 110°±10° view angle. If mounted at a lower height,
the detection range may be decreased.
110°±10°
26ft. 23 20 16 13 10 7 3 0 3 7 10 13 16 20 23 26ft.
4 Installing the Door/Window Sensor
IMPORTANT:
The distance between Door/Window Sensor (DD) and Magnet (EE) must not exceed
1.2 inch in closed state. This sensor should not be mounted on a metal frame.
This sensor should only be installed indoors.
The Door/Window Sensor (DD) can be mounted on a door or window.
MAX to 1.2 inch
7.4ft.
5.6ft.
0 3 7 10 13 16 20 23 26ft.
DD
DD
DD EE
18
Installation (continued)
Remove the Bracket (J) from the Door/Window Sensor (DD) by following the direction of the unlock marked on the side of Door/ Window Sensor (DD).
Hang the Door/Window Sensor(DD) on the Bracket (J) by following the direction of lock marked in the side of Door/Window sensor (DD).
Unlock Lock
Decide upon your placement position and attach the Bracket (J) with either
Screws (KK) or preinstalled double-sided adhesive tape.
OR
Pull out the battery insulator pull tab to activate the battery.
19
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Operation
1 4 Download the HubspaceTM app from the Apple App Store or the Google
Tap the `+’ button in the upper-right corner on the app screen to add your
Play Store.
Siren Hub.
My Home
2 Sign in if you have an account, or register to create an account then sign
in.
3 Connect your Security Kit to power and follow the instructions on the app
screen.
NOTE: Bluetooth®access is required for product setup. Android phones must also enable Location services to allow for Bluetooth scanning.
NOTE: Please remove the Battery Insulator Pull
Tab behind the battery from the Siren hub, Keypad and Sensors to get power
connected. The siren hub need plug into power and have a non-rechargeable
battery backup. This Hubspace hub requires a 2.4GHz Wi-Fi channel. Hubspace
only shows Wi-Fi networks that your product can use. If you do not see your
Wi-Fi network name when you attempt to connect your product, please check your
router settings or move your product closer to your Wi-Fi router.
5 Scan the QR code on the Siren Hub or in the Quick Start Guide.
HUBSPACE APP QUICK START GUIDE
XXXX-XXXX XXXX-XXXX XXXX-XXXX
NOTE: If the QR code cannot be scanned, you
can enter the code manually in the app. Tap Enter Code and follow the
instructions. You can find the QR code on the side of siren hub housing. If
the QR code is lost, you can press the siren hub reset button for 5 seconds to
put into setup mode and follow the app. instructions.
20
Operation (continued)
6 Using your Security Kit System.
Once the Siren Hub added successfully in the app, tap on the Home Alarm in the
app. to display the controls for adding the Keypads and Sensors. Plus “+” in
the app and follow the instructions. The Keypad or Sensor’s Bracket must be
removed first when add into app. – Manually Pair a Sensor or the Keypad: Press
and hold the onboard button of sensor/keypad for
5 seconds, Siren Hub beeps and the Connectivity/Network/Pairing LED indicator
starts blinking red. – Remove all known Sensors and Keypad: Press and hold the
reset button of sensor/keypad for 10 seconds Siren Hub should beep again).
You need to create a 6-digit PIN code before you can use security system. Tap
the “PIN Management” in the app. and follow the instructions to set up your
PIN.
Arming the system.
Armed Away Mode: On the keypad: Press , enter the PIN code and press . The
keypad will blink 3 times and the Hub alarm LED blinking green to indicate
success setting. On the App: Tap on the home page.
Armed Stay (Home) Mode: On the keypad: Press , enter the PIN code and press the Hub alarm LED will blink green. On the App: Tap on the home page.
. The keypad will blink 3 times and
Disarmed Mode:
On the keypad: Press
, enter the PIN code and press
and the Hub alarm LED will blink green.
On the App: Tap on the home page.
. The keypad will blink 3 times
Sending an Emergency signal: On the keypad: Press and hold for 3 seconds for
emergency. On the App: Tap on the home page.
Faulted sensors: On the keypad: The indicator will be red with a sound prompt.
Input the PIN code and press to preeced arming (ignoring the faulted sensors).
Or press to cancel the arming operation. Other keys (except ) are disabled in
this case.
21
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Operation (continued)
Wrong PIN Code: On the App: Tap “OK” to proceed or “Cancel” to cancel. On the
keypad: The key backlights will flash with a sound prompt if the PIN code is
not right. Input the PIN code again and press . No need to press or before re-
input. Press to cancel the operation. Entry Delay Setting: This is the time
users have to disarm the system before the alarm sounds. The default delay
time is 30 seconds (you can change the setting via app).The Siren Hub starts a
countdown after a sensor is triggered, the delay time will also be sent to the
Keypad. Exit Delay Setting: This is the time users have to exit the house
before the system arms itself. The default delay time is 30 seconds (users can
change the setting via app).The Siren Hub starts countdown after Armed Away or
Stay are activated, the delay time will also be sent to Keypad so that keypad
beeps as well to alert the user.
7 Set up your Voice Assistant.
You can connect your Smart Home Alarm System Kit to Google Home and Alexa from
the Hubspace app. Or, you can sign in to the Alexa app or Google Home and
connect to your Hubspace product from there.
22
Replace the Batteries
The app will notify you when a device’s battery gets too low. To replace the
battery, please disarm the system first to avoid unintended anti-tamper
alarms.
1 Replace the Keypad batteries
When you find the battery indicator is red and receive a “low battery” alert
through the app, follow the instructions below:
Disarm the system, and remove the keypad from the wall bracket. Open the
battery compartment cover and remove the old batteries and replace with new AA
batteries.
Hang the keypad back on the wall bracket.
2 Replace the Door/Window sensor battery The app will notify you when a
device’s battery gets low. To replace the battery, please disarm the system
first to avoid unintended tamper alarm.
Disarm the system. Remove the door/window sensor from the bracket. Loosen the
screw on the battery cover. Open the battery cover. Remove the old battery and
replace with new CR2032 battery.
Close the battery cover. Replace the screw on the battery cover. Hang the
door/window sensor on the bracket.
3 Replace the Motion Sensor battery
The app will notify you when a device’s battery gets low. To replace the
battery, please disarm the system first to avoid unintended tamper alarm.
Disarm the system. Remove the motion sensor from the wall bracket. Loosen the
screw on the battery cover. Open the battery cover. Remove the old battery and
replace with new AAA battery. Close the battery cover. Replace the screw on
the battery cover. Hang the motion sensor on the wall bracket.
23
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Specification
Item
Siren Hub
Keypad
Motion Sensor Door/Window Sensor & Magnet
Product Size
3.19 in L x 3.19 in 4.29 in L x 2.52 in
W x 1.6 in D
W x 1 in D
(w/Bracket)
2.36 in L x 1.57 in W x 1.34 in D
1.92 in L x 1.14 in W x .74 in D (Sensor) 1.88 in L x .32 in W x .25 in D (Magnet)
Power Source
Main Power: DC, 5V1A Backup Power: AA*3 Battery
AA*3 Battery
AAA2 Battery CR20321 Battery
Battery Life Up to 4hours
1.5 years
2 years
2 years
Protocal
Wi-Fi/Bluetooth/ Bluetooth Sub-G private protocal
Sub-G private protocal
Sub-G private protocal
Detection N/A
N/A
“110°±10°, 26.25ft The distance between
Range
with PIR detection” Door/Window Sensor
and Magnet must not
exceed 0.8 inch in
closed state.
Mounting Type
3M Adhesive 3M Adhesive Tape or Screw Tape or Screw
3M Adhesive Tape or Screw
3M Adhesive Tape or Screw
Mounting N/A Height
47.24 in – 59.00 in 78.74 in – 90.55 in N/A
above ground
above ground
Transmission “WIFI:328 ft in Distancet open area
BLE:131 ft in open area Sub-G:492 ft in open area”
131 ft in open area 492 ft in open area 492 ft in open area
Opperating 32 °F to 104 °F 32 °F to 104 °F
Temperature Up to 85% non- Up to 85% non-
condensing
condensing
32 °F to 104 °F_ Up to 85% noncondensing
32 °F to 104 °F_ Up to 85% noncondensing
Storage Temperature IP
Certification
-4 °F~122 °F
IP20 FCC/IC
-4 °F~122 °F
IP20 FCC/IC
-4 °F~122 °F
IP20 FCC/IC
-4 °F~122 °F
IP20 FCC/IC
24
Troubleshooting
Problem I cannot find the QR code.
Solution
It is on the Siren Hub housing. A copy of the QR code is also included in your
product’s documentation.
The QR code has become Under the QR code is a 24-digit code. You can enter
those manually
damaged. How do I instead of scanning the code. add the Siren Hub.
I lost my QR code. How do I add Siren Hub?
1. Make sure the product is connected to power. 2. In the Hubspace app, tap +, then Add Product. 3. On the Scan Product screen, tap the Search button in the lower-right corner. 4. Follow the on-screen instructions. Press the reset button and hold it for 5 seconds on the Siren Hub that enables it to be put into setup mode. When it enters that mode, it must indicate by beeping twice. Then it will broadcast the QR code information so that the unit can be added without using the QR code.
A product is on
The user will be required to put the Siren Hub into setup mode before the
another account. transfer can proceed. Pressing the siren reset button for 5 seconds into
How do I transfer it? setup mode. Scan the QR code and it will transfer to your account.
Check the LED indicator’s status.
1. Make sure the power indicator is on.
2. If both Internet and Join/Pairing indicators are off, there may be a
Siren Hub is listed as problem with your home router.
offline in the app
3. If the middle Internet indicator is off, and the Join/Pairing indicator is blinking, but not at a steady pace, there may be a problem with the
internet. Please check your home internet connection. You may need to
reboot your router.
4. If the middle Internet indicator is off, and the Join/Pairing indicator is
regularly blinking, once per second, then it means the siren hub is in
setup mode. You need to use the app to add the siren hub again.
The keypad does not Make sure the batteries are installed correctly and full of power.
work and no
You may need a new pair of batteries altogether.
indicator/button is lit NOTE: Do not use rechargeable batteries.
The”Not Ready”Sensor Please check the motion sensor and door/window sensor to make sure Alert Indicator (F) all sensors are good to use. of the keypad turn on
25
HOMEDEPOT.COM/Hubspace
Please contact 1-877-592-5233 for further assistance.
Troubleshooting
Problem
Solution
The Keypad does not When the keypad is communicating with the hub, it will not respond to
respond when some keys are pressed sometimes
button presses. When the Faulted Sensor indicator is red, only Confirm, Cancel and the Emergency buttons are allowed to be pressed. When no mode swithing key is pressed, the keypad will not respond to number, Confirm and Cancel keys pressing.
Sensors are listed as offline in the app after installation
They may be too far from the siren hub. Try and move the siren hub closer to the location of the sensors.
Unintended alarms Please try and position the sensor where they will not be triggered by pets.
by pets
Vibration or movement caused by pets bumping a sensor may trigger the sensor.
Unintended alarms by excessive heat or cold
Unintended alarms from other items
Please keep sensors away from the following: Direct sun exposure, electric
heaters, heat vents, fireplaces, drafty windows, air conditioners and AC
vents.
When placing your sensors in the home, please be aware that some things such
as billowing curtains, ceiling fans and sometimes shadows can trigger the
sensor.
Hub Alarm LED on One or more sensors disconnected, sensor is not ready or system arm
yellow.
bypassed.
The Hub cannot pair The Siren hub only can access up to 32 sub-devices. The paired sub-
more sensors
devices need to be removed before add the additional new sub-devices if
existing paired is over 32 sub-devices.
26
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et D é veloppement é conomique Canada
applicables aux appareils radio exempts de licence. L’exploitation est autoris
é e aux deux conditions suivantes : 1)L’appareil ne doit pas produire de
brouillage; 2)L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps
qu’aucune autre antenne ouémetteur.Cet équipement devrait être installé et
actionné avec une distance minimum de 20 centimètres entre leradiateur et
votre corps.
Questions, problems, missing parts? Before returning to the store, 8 a.m. – 7
p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday
1-877-592-5233 HOMEDEPOT.COM/Hubspace
Retain this manual for future use.