sygonix 2368619 Portable Solar Wall Light Instruction Manual

sygonix 2368619 Portable Solar Wall Light

Operating Instructions

Item No. 2368619

Intended use

• The product is a solar rechargeable light that can be wall mounted or separated for portable use.
• The product is intended for outdoor use. It has an ingress protection rating of IP65 and is protected from dust and low-pressure water spray from all directions.
• For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can result in or other hazards. Read the instructions carefully and store them in a safe place. Make this product available to third parties only together with its operating instructions.
• This product complies with the statutory national and European requirements. All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery content

• Product
• 2x wall plugs
• 2x mounting screws
• Operating instructions

Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Explanation of symbols

• The symbol with the exclamation mark in the triangle is used to indicate important information in these operating instructions. Always read this information carefully.
• This product is constructed according to protection class III.
• The arrow symbol indicates special information and advice on operation.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting per- sonal injury or damage to property. Such cases will invalidate the warranty/guarantee.

General information

• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dan-gerous playing material for children.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam, and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:
  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Consult an expert when in doubt about the operation, safety, or connection of the appliance.
• Maintenance, modifications, and repairs must only be completed by a technician or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.

LED light

Attention, LED light:

• Do not look directly into the LED light!
• Do not look into the beam directly or with optical instruments!

Rechargeable battery

• The rechargeable battery is permanently built into the product and cannot be re-placed.
• Never damage the rechargeable battery. Damaging the casing of the recharge-able battery might cause an explosion or a fire!
• Never short-circuit the contacts of the rechargeable battery. Do not throw the bat-tery or the product into fire. There is a danger of fire and explosion!
• Charge the rechargeable battery regularly, even if you do are not using the prod-uct. Due to the rechargeable battery technology being used, you do not need to discharge the rechargeable battery first.

Installation

• When drilling or tightening screws, make sure there are no cables, wires, or pipes located underneath the surface.
• Inadvertently drilling through electric cables can cause life-threatening electric shock!

Overview

1. Release tabs
2. Multi-function button (power / mode)
3. Solar panel unit
4. PIR sensor / battery status / mode indicator

Installation

Charging battery / location

Important

• Keep the panel clean to maximize charging efficiency. See section “Care and clean-ing”.
• Before first use, place the panel under bright sunlight for at least 5 hours to charge the battery.

1. Select a location where the solar panel receives the most sunlight.
2. Do not place the product near other light sources such as streetlights. This will prevent the sensor from ac-tivating.
3. Battery status indicator:
4. Green: ≥70 %
5. Orange: 30 – 70 %
6. Red: <30 %

Motion detection angle

Motion detection:

• Works best when the subject walks across the sensor.
• Does not work well behind glass.

Mounting

Important Check if the screws are suitable for the mounting surface material. Use the wall plugs if necessary. If in doubt consult a professional.

See section “Attach / remove light” for further information.

1. Mark a spot on a surface 1.6 m above ground level.
2. (If needed) drill a hole for the wall plug.
3. Insert the first screw. Leave some of the screw head protruding and then hang the product.
4. Make sure the product is vertically aligned.
5. Mark the position for the second screw hole.
6. (If needed) drill a hole for the wall plug.
7. Secure the product with the second screw.

Attach / remove light

Important Do not use force to pull the light away from the solar panel unit. This can damage the locking mechanism.

1. Detach the light by pressing both release tabs as shown. Gently slide the light out from the solar panel unit.
2. When connecting the light to the solar panel unit, make sure the two parts “click” together

Operation

Important

• If the solar panel is not exposed to enough sunlight, conserve battery by reducing the power consumption at night. In the “wall light” configuration, select “Mode 2”.
• The product may run out of battery and will not switch on. If this happens place it under bright sunlight to recharge.

Wall light (3 modes)

When the light is connected to the solar panel unit:

1. Press and hold the multi-function button for 1.5 seconds to switch the power ON/OFF.
2. Press the multi-function button repeatedly to switch modes:
   Mode| Indicator| Description
   ---|---|---

1

|

Red

| LED ON (50 lm).

When PIR sensor is triggered, LED gets brighter (1000 lm).

2

|

Green

| LED OFF (0 lm).

When PIR sensor is triggered, LED turns ON (1000 lm).

3| Orange| LED constantly ON (200 lm) LED turns OFF after 6 hrs

Motion sensor
The light will remain on for 10 seconds after the motion stops.

Portable light (2 modes)

When the light has been separated from the solar panel unit:

1. Press and hold the multi-function button for 1.5 seconds to switch the power ON/OFF.
2. Press the multi-function button repeatedly to switch modes:
3. Mode 1 (100 lm)
4. Mode 2 (200 (lm)

Disposal

Electronic devices are recyclable waste and must not be disposed of in household waste. At the end of its service life, dispose of the product in accordance with applicable regulatory guidelines. You thus fulfill your statutory obligations and contribute to the protection of the environment

Care and cleaning

• Do not use any aggressive cleaning agents, rubbing alcohol, or other chemical solutions as they can cause damage to the housing and malfunction.
• Clean the product with a dry, fiber-free cloth.
• Use a cloth moistened with water if needed.

Technical data

• Rechargeable battery ……………….. 1 x 3.7 V Lithium 18650 2000 mAH battery (7.4 Wh)
• Solar panel type ……………………….. Epoxy mono-crystalline 1 W, 4.86 V
• Efficiency …………………………………190 lm/W
• Power ……………………………………..10 W
• Recharge time …………………………. 10 hours (optimum conditions)
• Brightness ………………………………..max. 1000 lm
• Ingress protection ……………………..IP65 / IK10
• Protection class ………………………..III
• Colour temperature ……………………4000 K
• PIR sensor ………………………………. Detection angle: 120º, Detection distance: >5 m
• Installation height ………………………approx. 1.6 m
• Operating conditions …………………. -10 to +45 ºC, ≤80 % RH (non-condensing)
• Storage conditions ……………………. -20 to +60 ºC, ≤80 % RH (non-condensing)
• Dimensions (L x W x H)…………….. 80 x 72 x 225 mm
• Weight …………………………………….approx. 277 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or capture in electronic data processing systems requires prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing. Copyright 2021 by Conrad Electronic SE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>