BLNAN LS-CL-G3-24W-Dim-WYRGB RGB LED Flush Mount Ceiling Light with Remote Control User Manual

RGB CEILING LIGHT WITH REMOTE
Product Type: LS-CL-G3-24W-Dim-WYRGB

LS-CL-G3-24W-Dim-WYRGB RGB LED Flush Mount Ceiling Light with Remote

Control

INTRODUCTION

Dear customer,
Thank you for purchasing our RGB ceiling light.
In order to use this product correctly, please read and keep this instruction for future reference.
We are dedicated to the customers to bring a convenient and comfortable experience. If you have any questions, please contact the following Email address: [email protected]

PRODUCT INTRODUCTION

The center light and outer RGB ring can be lit separately or simultaneously by the remote control.
Center Light:

1. The color temperature: 3000K ~ 6500K
2. Continuous brightness adjustment: 10% ~ 100%

Outer RGB Ring:

1. 7rgb colors
2. 7 rgb dynamic modes ( adjustable speed)

SPECIFICATIONS

2.4G REMOTE CONTROL INSTRUCTION

1. Center Light On/ Off

2. Outer RGB Ring On/ Off

3. Increase Brightness (for Center Light/ Single RGB Color)

4. Decrease Brightness (for Center Light/ Single RGB Color)

5. K Decrease Color Temperature (for Center Light)
   S-: Decrease Speed (for RGB Dynamic Modes)

6. K- Increase Color Temperature (for Center Light)
   S+:Increase Speed (for RGB Dynamic Modes)

7. Night Light (3000, 10% brightness)

8. Change Single RGB Color/ Pairing Button

9. Change RGB Dynamic Modes

10. Change Color Temperature (3000K/4000K/6500K)

11. 60-second Off-Delay

12. Pause (for RGB Dynamic Modes)

NOTE

1. The remote control batteries are not included.
2. The remote control range is within 10 meters.
3. For these 4 buttons : If the main light and RGB ring are both on, this function only works for the main light.
4. To operate the pairing: Turn off the power for 10-20 seconds, then turn on the light. Press and hold this button until the light flashes once, indicating that the code pairing is successful.

MEMORY FUNCTION

1. If you keep the current settings for 1 minute and turn off the ceiling light for more than 10 seconds, the light will remember the previous setting when it’s turned back on.
2. The memory function does not include the delay off and pause button functions.

WALL SWITCH OPERATION

Wall Switching Steps: Switch within 5 seconds (not applicable for dimmers)

1. If the center light and the RGB ring are both on, after memorizing the setting, the wall switching will only control the light that was set last time.
2. When the center light is on alone, the wall switch will switch between 3000K/4000K/6500K and the last setting.

ACCESSORIES LIST

INSTALLATION STEPS

1. Please rotate and remove the base plate, fix the base plate to the junction box with screws provided.
2. Please use the correct size junction box. The screw hole distance of the junction box: 2.75-5.4 inches.
3. Hang up the wire rope and connect the wires of the corresponding color, then push and feed all wires up into the junction box. (Description of the supply terminals: Black: Hot Wire; White: Neutral Wire; Green: Ground Wire)
4. Push and rotate the lamp and install it onto the base plate.

QUESTION & ANSWER

1.Why does the remote control not work?

A:Try to replace the new batteries. B: Try to pair the remote control and the light. C:If you have any questions, please contact the following email address: [email protected].

2.How to pair the remote control and the light?

First step: power off for 10-20 seconds, Second step: power on again, Third step:long press for 5 seconds to match the code, the ceiling light flashes once and the pairing is successful.

3.How to cancel the pairing between the remote control and the light?

First step: power off for 10-20 seconds, Second step: power on again, Third step:long press @for 5 seconds, the ceiling light flashes twice and the pairing is canceled successfully.

PRECAUTIONS

♦ Precautions Before Installation

1. Power off before installation.
2. Do not exceed the rated voltage.
3. Do not install it on surfaces where are not stable or deformed.
4. Do not install it on or above the surface with high temperatures.
5. Please make sure that no gas, water, or electricity pipes and wires can be drilled through or damaged in your chosen mounting location.

♦ Precautions During Installation

1. There must be no corrosive, explosive, or flammable materials around the lamp.
2. User should connect the cable correctly, and the lamp should be installed by a qualified electrician.
3. Please pay attention to connecting the wires correctly, and make sure the  cable connection comply with national regulations.
4. Please make sure that the lampshade is clear in case of low luminous efficiency.
5. Please make sure that illuminants are securely fixed during the installation.

♦  Precautions About the Product

1. It is not suitable for dimmers and electronic switches.
2. The LED light source inside the lamp body can not replaceable.
3. The lampshade cannot be opened.
4. Do not touch the light when it is running.
5. Do not look straight into the light source (illuminant, LED, etc.).
6. Do not let the children touch this light and packaging to avoid danger.

MADE IN CHINA

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>