ZHIXUAN X222 Folding Drone User Manual

ZHIXUAN X222 Folding Drone

REMOTE CONTROL FUNCTION DESCRIPTION

1. Mobile phone rack
   Pull out the mobile phone handle and clamp the mobile phone.

2. 2.4G frequency alignment
   When the aircraft is offset in the forward direction, it is necessary to press the fine-tuning function key first to enter the fine-tuning operation,and then push the rocker in the backward direction. Every time the rocker is pushed, the forward deviation speed will be slowed down until it is no longer offset. The rocker will not be automatically removed from the fine-tuning operation for consecutive 3S.
   It must be operated after 2.4 G alignment is completed

3. One-button take-off and one-button landing It is suggested that the height of this product is determined by barometer. Due to the influence of various environmental temperatures and otherdifferent factors, it is normal for the aircraft
   to change evenly at the beginning of flight or at low voltage.

4. Flight control

5. Throttle (left rocker)

6. Rotation (left rocker)

7. Forward and backward (right rocker)

8. Left and right side flight (right rocker)

Remote Control and Aircraft Battery Installation and Charging Instructions

1. Remote control battery installation
   Put the battery correctly according to the electrode instructions (+,- of the battery box as shown

2. Aircraft battery charging

3. Remove the battery from the aircraft;

4. Connect the battery to the specific charging cable, and then insert the cable into the charging equipment such as the USB port of the computer.

5. When the remote control is charged, the indicator lights up while be off when charging completion.
   The charging time is about 60 minutes

6. Installation and startup of aircraft battery
   Put the fully charged battery into the battery slot of the aircraft and hold down the power switch until the aircraft lights up.

Aircraft installation

1. Folding function
2. Installation of aircraft blades
   Please install the propeller in the correct direction, and lock the screw after installing the support arm of the aircraft corresponding to the mark (A/B) on the propeller.

Direction Definition and Mode Selection of Headless Mode

When switching to headless mode, the aircraft will give up its front, back, left and right directions, and take the nose direction (one side with camera) of the aircraft at 2.4 G frequency alignment as the forward direction.

1. Direction definition before take-off: Put the forward direction of the aircraft directly in front of you (there is a camera side, and then turn on the remote control for 2.4 G frequency alignment to complete the headless mode direction definition of this flight.
2. Press headless mode when flying, and the remote controller keeps making noise; The aircraft lights quickly flash and enter the headless mode; Press the headless mode key again, and the remote controller will make a di” and “di” sound, that is, exit the headless mode.

Note: Before entering into the headless mode, the forward direction must be determined, that is, the direction of the aircraft on the ground after startup.

Horizontal Calibration
If the aircraft cannot rise vertically during takeoff, it can be corrected with the inner eight unlocked. At this time, the indicator light flashes rapidly. When the indicator light is steady on, the correction is complete. When the correction command is executed, it must be executed in a steady state parallel to the horizontal line, otherwise, the correction effect will be affected.

Fine-tuning Operations

If the aircraft has been drifting in a certain direction or rotates left/ right in place, the aircraft can be slightly adjusted through the following operations to make the aircraft reach a stable flight state.

• Turn on the power switch of the aircraft, place the aircraft on the flat ground, then the aircraft light flashes, turn on the remote control power switch, the remote control and the aircraft automatically complete the frequency, then the remote control light and the aircraft light is steady on.

Speed Switch
The speed switch is divided three speeds for the flight of forward, backward and left & right side. It defaults to gear 1 after power on. And when press the remote control with two sounds of Di for the gear 2, three sounds of Di for the gear 3 and one sound of Di for returning to gear 1.

360° rolling

Implementation steps:

1. Press the 360° rolling button, and the remote controller will continue to send out “di” didi;
2. Push the right rocker. At this time, the aircraft will carry out 360° rolling according to the pushing direction of the right rocker.

When the aircraft enters the low voltage state, the carry out 360° rolling function will be automatically prohibited

Problem solving guidelines

Note: the batteries of newly purchased products are low voltage, please fill the battery before use!

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>