legrand WNAL33/43 adorne Wireless Smart Scene Controller Switches Instruction Manual

legrand WNAL33/43 adorne Wireless Smart Scene Controller Switches

Catalog Number

REGULATORY INFORMATION

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 90 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons. NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment. Contains FCC ID: 2AU5D-AHAWS IC NOTICE: This device complies with Industry Canada license- exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device. RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 90 mm to the human body. Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment. IC: 25764-AHAWS HVIN: WNAL33, WNAL43

Wireless Smart Scene

Wall plate sold separately

Choose a place to install the Device

For indoor installation only. This device can be installed in any standard electrical wall box of any gang size, or on any flat wall surface.

WARNING

To prevent severe shock or electrocution, always disconnect power at the service panel before beginning work.

WARNING

Failure to connect the ground wire will result in an unsafe installation that could lead to personal injury.

One-Gang Electrical Box Installation

Note: Skip Section 2, if installing on a wall surface

Electrical box installation Remove the grounding wire label from back of device to access the ground wire. Connect it to box ground using provided wirenut. If installing this device with sofTap smart Switch with Netatmo, WNAL10 or other wired Netatmo devices, follow their instructions on how to terminate the spare wires in the box. Mount device to wall box with screws provided. Tighten screws just enough to hold frame in place. Do NOT overtighten

Multi-Gang Electrical Box Installation

NOTE: Skip section 2 if installing on a wall surface.

In case of multi-gang installation, replace the provided frame with adorne™ multi gang frame. While holding the frame with one hand, push the device up slightly until it snaps out and then pull it out of the frame. Secure the device to the multi gang frame using frame mounting screws.

Remove spacers from the frame.

Since this dimmer fills the frame completely, you will not need the spacers. From the back of the frame, pinch the tabs on the spacer to release.

Wall Surface Installation

NOTE: See Section 2, if installing in a box.

Use provided double sided stickers to install on a tiled or other smooth surface. Markings on the back of the device indicate location for the stickers. If the wall surface is uneven or rough where the adhesive may not work, use drywall screws if going on a wall stud or drywall anchor if stud is not present.

Set Up Your System

Remove battery insulation tab before starting the setup.

• a. Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
• b. Connect your smart device to your home network by following the step by step instructions in the app.
• c. Use the app to control your smart device.

Getting to Know Your Battery Powered Switch

LED Indicator Light Explanations

Reset to Factory Default

To manually reset the device to factory defaults press and hold the EZ button for 7 seconds until you see the LED blink red then release. The LED will turn off when the reset is complete Due to ongoing product improvements, Legrand reserves the right to change specifications without notice. For the most recent instruction sheets or more information on this product, please see this link or scan the QR code https://www.legrand.us/p/wnal33w1 https://www.legrand.us/p/wnal43w1

Snap wall plate to frame

There are three click-stops to adjust the fit of the wall plate to the dimmer and the wall.

Enclencher la plaque murale dans le boîtier.

Il existe trois crans pour régler la position de la plaque murale sur le commutateur et le mur.

Encastre la placa de pared al bastidor.

Hay tres topes de profundidad con clics para que pueda ajustar la forma en la que la placa para pared se alinea con el interruptor y con la pared.

Technical Assistance

877-295-3472 www.adornemyhome.com/install Assistance technique : 877-295-3472 www.adornemyhome.com/install Asistencia técnica: 877-295-3472 www.adornemyhome.com/install LIMITED TWO-YEAR WARRANTY Limited two-year warranty information for adorneTM products is available at www.adornemyhome.com/warranty. Limited warranty information for adorneTM products may also be obtained free of charge by sending a written request, along with your proof of purchase (including purchase date), to: Legrand Attn: adorne Customer Service/Warranty Department 50 Boyd Avenue Syracuse, NY 13209 No: 341337 – 08/21 © Copyright 2021 Legrand All Rights Reserved.

References

• Search Results Page
• adorne® Warranty ⎸Legrand
• Legrand US | Delivering and Managing Power, Light, and Data
• The adorne® Collection | Legrand
• adorne® Warranty ⎸Legrand
• adorne Home|Away Wireless Smart Switch with Netatmo
• adorne® Wake Sleep Wireless Smart Switch with Netatmo, White | Designer Switches and Outlets | Wiring Devices

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>