VEVOR M1B-LS-3305 Power Benchtop Planers User Manual

VEVOR M1B-LS-3305 Power Benchtop Planers

Product Information

The Thicknesser (Model: M1B-LS-3305) is a power tool designed for planing wooden planks and dry wood. It is not suitable for planting other materials such as metals, plastics, branches, tree trunks, wet wood, and very hard wood. The tool is intended for both household and professional use.

The product specifications are as follows:

• Model Specs: M1B-LS-3305
• For US user
• Rating(s): 110V~60Hz 2000W
• First Feed Speed: 4.3m/min
• Second Feed Speed: 7.0m/min
• Blade: 3pcs
• Max. Planing Width: 330mm
• Planting Depth: 0-3mm
• Planing Height: 6-160mm
• G.W: 30kg
• N.W: 28kg
• Working Table Size: 330x290mm
• Packing Size: Tested wood width is 150mm for feeding speed

The tool comes with various features and components including an E-Knife blade bit gauge, a depth adjustment handle, a depth label, an overcurrent protective device, a roller bar, a switch, an open spanner, rubber feet, a speed control knob, a carrying handle, an extension table, an Allen wrench, and a carbon brush cover.

Product Usage Instructions

1. Before using the tool, carefully read the instruction book provided.
2. Ensure that the tool is connected to a suitable power supply (110V~60Hz).
3. Install the rubber feet (O) by placing 4pcs rubber feet into the four holes in the bottom of the machine if not using a foot frame for working.
4. Install the depth adjustment handle (F) by placing it on the protruding shaft to the right of the machine’s top surface. Push on the handle firmly and lock it with the supplied screw.
5. Wear ear protection, safety glasses, and a dust mask while operating the tool for personal safety.
6. Ensure that the material being planed is wooden planks or dry wood and not any other prohibited materials.
7. Adjust the planting depth using the depth adjustment handle (F) and refer to the depth label (H) for accurate measurements.
8. Use the speed control knob (P) to set the desired feed speed (4.3m/min or 7.0m/min).
9. Turn on the tool using the switch (L) and feed the material through the machine carefully.
10. Regularly check and replace carbon brushes (W) as needed to maintain optimal performance.

• If you are unsure about how to use the tool correctly, please contact the factory for assistance.
• This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual.
• The appearance of the product shall be subject to the product you received.
• Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SAFETY INSTRUCTIONS

• IMPORTANT: carefully read the instructions in this manual as well as the general safety instructions before using this tool.
• Before using the tool, read the instruction book carefully.
• Class ll appliance, reinforced insulation, or double insulation
• Keep the packaging material out of the reach of children — the risk of suffocation.
• WARNING! Always take basic safety precautions when using power tools to safeguard against the risk of fire、electric shock and /or personal injury.

1. For safe operation. We recommend that you take appropriate measures for the protection of hearing if the sound pressure of 85dB (A) is exceeded
2. Keep the work area clean. Cluttered work areas increase the risk of accidents and injuries.
3. Keep the workplace environment safe. Do not use power tools in damp or wet areas. Do not expose power tools to rain. Make sure the work area is well-lit. Do not use power tools in explosive environments, such as in the vicinity of flammable liquids gases, or dust.
4. Protect against the risk of electric shock. Avoid body contact with earthed surfaces, Such as pipes, radiators, cookers, and refrigerators.
5. Keep children at a safe distance. Do not allow onlookers to touch the tool or the extension cord. Onlookers should be kept away from the work area.
6. Put away tools that are not being used. When not in use, store the tool in a dry place out of the reach of children.
7. Do not force the tool. The tool does the job better and safer when used at the rate for which it was designed.
8. Use the correct machine. Do not force small machines or accessories to perform jobs that require a powerful machine. Use tools only for their intended purpose.
9. Wear suitable clothing. Do not wear loose clothing or jewelry. they can be caught in moving parts. Non-slip shoes are recommended when working outdoors. Wear a hair net if you have long hair.
10. Wear safety glasses. Wear a dust mask if the work generates dust.
11. Be careful with the cable. Never carry the tool by the cable. Do not pull the cable to disconnect the plug from the socket. Keep the cable away from heat oil and sharp edges.
12. Secure the workpiece. Secure the workpiece with a stand. This is safer than using your hands and means you have both hands free to operate the tool.
13. Do not overreach. Always maintain a firm footing and good balance.
14. Maintain the tool in good care. Keep cutting tools sharp and clean for better, safer work. Follow the instructions for lubricating and for the replacement accessories. Check power cords regularly. If damaged, they must be replaced at an authorized service center. Check extension cords at regular intervals and replace them if they are damaged. Keep the hands clean、dry and free from oil and grease.
15. Always unplug the power cord. when the tool is not being used, and before carrying out service work or changing accessories, such as knife blades/carbon brush/gears, and so on.
16. Remove adjuster keys/spanners and other assembling tools. Remove adjuster keys/spanners and other assembling tools before starting the power tool.
17. Avoid accidental starting. Never carry a power tool with your finger on the switch when it is connected to the mains. Make sure the power switch is in the OFF position before plugging in the power cord.
18. If using the tool outdoors. only use an extension cord approved for outdoor use.
19. Stay alert. Always be careful when using the equipment. Use your common sense, Do not use the tool if you are tired.
20. Connect dust extraction equipment. If dust extraction and dust collection equipment is provided. This should be connected and used correctly.
21. Check for damaged parts. If a guard or some other part has been damaged, check carefully before using the tool to ensure that it will operate correctly and as intended. Make sure that moving parts are properly adjusted and do not jam and that no parts are incorrectly fitted or damaged. Check for any other factors that could influence functionality. Guards or other parts that are damaged must be repaired or replaced by an authorized service center. Unless otherwise specified in these instructions. If the power switch does not work, it must be replaced by an authorized service center. Do not use the tool if it cannot be switched on and off using the power switch.

• WARNING! The use of accessories or attachments other than those recommended in these operating instructions can result in personal injury. Repairs must only be carried out by qualified personnel. This power tool has been manufactured in compliance with current safety standards and requirements. Repair may only be carried out by qualified personnel using identical spare parts. Failure to carry out repairs correctly can result in the risk of personal injury/death or material damage.
• NOTE: A temporary voltage drop can occur when starting the machine. Which could affect other equipment. If the main supply impedance is Zmax. is lower than 0.206 ohms, this kind of interference is common. Contact your electricity supplier for more information.

IMPORTANT SAFETY INSTRUCTIONS

1. Wear safety glasses, Don’t send wood into the outfeed side.

2. Before use, check that all screw connections are properly tightened.

3. Do not force the tool. Let the feed mechanism do the work. Never insert objects or body parts in the outfeed.

4. Check regularly that the rubber roller and iron roller are clean. If the rollers are contaminated the workpiece will not infeed correctly- risk of personal injury.

5. Do not machine workpieces with many knots or sprigs.

6. The operating position is in front of the machine. Stand by the side of the infeed table.

7. Remove any nails, screws, and other metal objects from the workpiece before machining.

8. Check that the blades are correctly installed.

9. Handle the knife blades with care–risk of personal injury and/or damage to property.

10. Never start to planer until the blade shaft has reached full speed.

11. Never use blunt blades-risk of kickback.

12. Always replace or sharpen all blades at the same time. All blades must be of the same size and weight.

13. Never insert your fingers or other body parts in the chip outlet side–risk of personal injury–
    DANGER.

14. Pls check the recoil claw is in the correct position.

15. If infeed wood is not smooth, pls don’t force the wood, check if the machine has some problems.

16. Do not wear gloves to plane wood.

17. Do not place wet wood, will cause the feed roller to slip and lead a machine to break.

18. Do not plane hardwood, will shorten the working life of the knife blades.

19. Do not plane the wood too long, the machine will be overloaded, influencing the wood planing surface effect.

TECHNICAL DATA

Model：

Specs:

| M1B-LS-3305

For US user

| M1B-LS-3305

For European users

---|---|---
Rating(s):| 110V~60Hz 2000W| 230V~50Hz 2000W
First Feed Speed:| ≥4.3m/min| ≥4.3m/min
Second Feed Speed:| ≥7.0m/min| ≥7.0m/min
blade:| 3pcs| 3pcs
Max. planing width:| 330mm| 330mm
Planing depth:| 0-3mm| 0-3mm
Planing height:| 6-160mm| 6-160mm
G.W:| 30kg| 30kg
N.W:| 28kg| 28kg
Working table size:| 330x290mm| 330x290mm
Packing size:| 570×360×505mm| 570×360×505mm
Tested wood width is 150mm for feeding speed

DESCRIPTION

1. The tool is designed for planing wooden planks and dry wood. It is forbidden to plane other materials. such as metals、plastics、branches、tree trunks、 wet wood and very hard wood.
2. The tool is intended for household and professional use.
3. Pls use this machine under correct operation, if don’t know how to use it, pls contact with factory.
4. E- Knife blade bit gauge
5. F- Depth adjustment handle
6. G- Carrying handle
7. H- depth label
8. I- Overcurrent protective device
9. J- Extension table
10. K -Roller bar
11. L -Switch
12. M -Allen wrench
13. N- Open spanner
14. O- Rubber feet
15. W- Carbon brush cover
16. P- Speed control knob
17. Advised to wear ear protection.
18. Advised to wear safety glasses.
19. Advised to wear the dusk mask.

OPERATION STEPS

Unpacking

• Carefully unpack the machine. The packaging must be recycled in accordance with local regulations.
• WARNING! Turn off the machine and unplug the power cord before cleaning 、 performing maintenance and adjustment.

Assembly

• Before using the machine must be in accordance with the requirements of the assembly complete.

Evacuation of shavings and woodcuts:

• The tool is equipped with a dust hood with a vacuum cleaner connection (V), this dust hood is at the back of the machine for connection to a vacuum cleaner connection.
• A flexible hose(not supplied) can be connected to the collector. Some species of wood or processed wood produce sawdust harmful to health.
• Pls attention: Always use the tool must be connected to a vacuum cleaner.

Install rubber feet (O):

• If no need to use a foot frame to work, pls put 4pcs rubber feet into the four holes in the bottom of the machine.

Install depth Adjustment handle

• Place the depth adjustment handle (F) on the protruding shaft to the right of the machine’s top surface. Push on the handle firmly and lock it with the supplied screw.

Adjust the depth of the planer

• In order to be able to completely correct and safely operate this machine, the User must know how to correctly adjust. Very Important
• Rotate the depth adjustment handle(F) a circle, the machine depth can be raised or lowered by 1.5 mm.

Adjust speed controller (P)

• This machine has a two-speed function. 1 and 2-speed adjustment level, Position 1: wood feed speed 4.3M/minutes. planer big hardness wood.
• Position 2: wood feed speed 7M/minute, planer normal hardness wood.
• under the machine stop state, Use your thumb to press the governor button and rotate clockwise to position 2.
• Before using, pls plane the wood a few times, that’s can ensure the surface of the wood is completely horizontal in later use. Please refer to the correct wood width range to adjust the depth of the one-time planer:
• At first, the user needs a ruler to measure the thickness of the wood to be planed, Then an observation depth label (H) to adjust the depth label to the thickness of the planer required by the user.
• Such as: the thickness of the wood it’s 200mm, user wants to planer 2mm, so the depth label pointer is 198mm, In this way, the thickness required by the user can be reached during the one-time working process.
• Pls note: The distance between the bottom of the machine and the knife shaft is the thickness of the wood when it is planed; The difference between the thickness of the wood when it comes out of the machine and the thickness when it comes in is the thickness of the wood that was shaved off.

1. Width of wood 0-100mm, we suggest cutting depth adjust 0-3mm, Max 3mm per time.
2. Width of wood 160-210mm, we suggest cutting depth adjust 0-2mm, Max 2mm per time.
3. Width of wood 210-330mm, we suggest cutting depth adjust 0-1mm, Max 1mm per time.

• Warning! The length of the wood must not be less than 153mm. The thickness of the wood must not be less than 10mm.

Operate switch (power ON/OFF)

• Plug the power cord into the main supply. If you are using an extension cord, the cross-section of the conductors must be sufficient for the tool’s power supply.
• Avoid inappropriate use of cable. as this can lead to voltage drop and cause power loss and overheating.
• Uppress the button marked “I” to start the machine. Down press the button marked “O” to stop the machine.

OPERATION

Coarse PLANING

• Coarse planing is used to provide a reference surface for machining.

1. Set a small removal setting for the best surface finish.
2. Process where possible along the grain.

Note : the surface finish is affected by various factors.

1. the wood’s hardness, moisture content, and fiber structure. etc.
2. Blade sharpness, machining direction, material removal per pass., etc.
3. Perform test machining to find the best setting.

PLANING
Planning involves material removal of the workpiece to the desired thickness and the machining of the surface opposite a coarse planed reference surface.

MAINTENANCE

WARNING : Turn off the machine and unplug the power cord before cleaning and maintenance, Do not use water or other liquids to clean electrical parts.

CHECK AND REPLACE THE CARBON BRUSH

1. Turn off the machine, unplug the power cord, and wait until all moving parts have stopped completely.
2. Dismantle the carbon brush cover (W) as illustrated using a screwdriver.
3. Fit the new carbon brushes. Always replace both carbon brushes at the same time.
4. Replace the carbon brush cover (W).

Overcurrent protective device correct use and replacement (I)
When the load power is too large, the current exceeds the load, so the overcurrent protective device will jump!

1. When the overcurrent protective device jumps, first disconnect the power supply of the machine, then press the protective button to reset it
2. When pressing the protective button to reset it, don’t reboot immediately. Need to wait for the machine temperature to cool then start for use.
3. If overcurrent protective device jumps frequently. Pls replace a new one.

ADJUST TABLE EXTENSION (J)
Attention: this adjustment is already factory set ok, in order to avoid affecting the function of the machine. need to check again.

1. Put the engine body rise to a suitable height , so that it is easily assembly.
2. Place a horizontal rule on the main worktable, and use the rule to measure the table extension (J) and the main worktable’s level.
3. If the table extension (J) is not flush with the main worktable, loosen the nut and turn the screw until the table extension’s rollers and the main worktable touch the ruler, Adjust both the left and right-hand table extensions (J).

ENGINE BODY LEVEL ADJUSTING

• ATTENTION: This adjustment is already factory set ok. in order to avoid affecting the function of the machine. need to check again.
• Poor parallelism is usually caused by misaligned blades or A fall in transit that causes the body to tilt. Always check that the blade holder and the work table are parallel before attempting to adjust the parallelism setting.
• The engine body is lowered to a certain height by rotating the handle, and two wooden blocks of the same height are placed at the lower end of the body and clamped tightly

1. Loosen the two screws on the handle of the right panel using a cross screwdriver, see picture 1 Attention: only need to adjust the right panel
2. Take off the right pane
3. Use a 24mm open wrench +30mm open wrench to adjust the engine body up and down. Position 1 uses a 24mm open wrench, and position 2 uses a 30mm open wrench. 24mm open wrench clamp 24mm nut do not rotate and turn the 30mm open wrench one turn to the left (clockwise) to keep the screw nut loose
4. Use a 24mm open wrench adjust the 24mm nut, and rotate clockwise to raise the engine body and counterclockwise to down the engine body Until the engine body is level with the base
5. Use 24mm open wrench clamp 24mm nut do not rotate, use 30mm open wrench tighten 30mm nut

Replacing and Adjusting the blades

WARNING! Turn off the machine, unplug the power cord, and wait until all moving parts have stopped completely before replacing or adjusting the blades.

Dismantling the knife blade

1. Use Allen wrench (N) to remove the dust hood (V) by loosening the screws (U), see the below picture.
2. Use the double open wrench (N) to loosen the blade locking plate (B) and knife blade (C) by turning the outer hexagon bolt (A) clockwise. The knife blades are spring-loaded (D) and can be removed when the blade locking plate is removed.
3. Remove the knife blade and blade locking plate.

Install the knife blade

1. First, ensure that the pressure springs (D) on the knife shaft are in the
2. fixed holes 2. Align the hole in the knife blade with the pin in the blade locking plate,
3. Insert the 8 outer hexagon bolt (A) into the fixed hole of the blade locking plate
4. Insert the knife blade (C) knife locking plate(B) and 8 outer hexagon bolts (A) together in the slot and lock in position by turning the outer hexagon blot (A) anticlockwise but not 100% tightened. Ensure that the blade’s face is in the right direction (see picture).
5. Set the height of the knife shaft of the knife blades as 1mm with the bit
   gauge(E) so that two support blocks on the left and right sides of the bit gauge are pressed against the knife blade. (Loosen, if necessary, the clamping screws to move the blade to the correct position.) When the knife blade is positioned correctly. Hold it firmly in place and tighten all outer hexagon bolt (A).

Warning! Check that total of 24 screws are tightened. Turn the blade holder by hand to check that it rotates easily and smoothly. Handle the blades with caution to avoid personal injury and/or damage to property.

LUBRICATION

1. Regularly remove shavings from the depth setting chains、reduction drive and lifting screws for the blade holder.
2. Remove chips with a cloth and brush and lightly grease with a clean brush dipped in oil.
3. Never pour oil directly on the components– too much oil means dust will stick and impair lubrication, which in turn shortens component life.
4. The balde holder’s bearings are sealed and must not be lubricated.

MAINTENANCE

1. Keep the machine clean and free of dust and chips.
2. Clean reaped materials from the blade holder and tongues and carefully lubricate with a clean brush dipped in oil.
3. Remove resin and the like from the rollers and work table with a non-flammable solvent.
4. Clean plastic parts with a damp cloth and mild detergent. Never immerse the tool in water or any other liquid. Never use detergents or alcohol.
5. Always check that all guards and other components are correctly fitted before use. Guards or other parts that are damaged must be repaired or replaced by an authorized service center unless otherwise specified in these instructions.

• This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste but must be taken to a collection point for recycling electrical and electronic devices.
• Manufacturer: ZHEJIANG LANGCHENG INDUSTRY&TRADE CO., LTD Address: No.18 Weisan East Road, Hardware Machinery Industrial Zone, Tongqin Town, Wuyi County, Jinhua City 321201 Zhejiang, P.R.China Importer: WAITCHX
• Address: 250 bis boulevard Saint-Germain 75007 Paris
• Importer: FREE MOOD LTD
• Address: 2 Holywell Lane, London, England, EC2A 3ET
• EUREP UK LTD
• UNIT 2264, 100 OCK STREET, ABINGDON OXFORDSHIRE ENGLAND OX14 5DH
• EUREP GmbH
• Unterlettenweg 1a, 85051 Ingolstadt, Germany
• E-mail:CustomerService@vevor.com
• NEED HELP? CONTACT US!
• Have product questions? Need technical support? Please feel free to contact us:
• CustomerService@vevor.com

Documents / Resources

| VEVOR M1B-LS-3305 Power Benchtop Planers [pdf] User Manual
M1B-LS-3305 Power Benchtop Planers, M1B-LS-3305, Power Benchtop Planers, Benchtop Planers, Planers
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>