Laview LVX2PWUS X1 Star Projector and Home Planetarium User Manual

LVX2PWUS X1 Star Projector and Home Planetarium
User Manual

What’s In the Box

LASER LIGHT
DO NOT STARE INTO THE BEAM CLASS 1 LASER PRODUCT Diode Laser – Max. Output <0.39 mW Wavelength 510-525 nm
Laser Warning
Use of controls or adjustments or performance of procedures other than those specie herein may result in hazardous radiation exposure.
This product is classed as a Class 1 laser product and complies with the applicable parts of IEC/EN 60825-1 Ed.
2.0:2007 and Ed. 3.0:2014.
Do not stare into the beams emitted from the product. Intentional long term viewing of CLASS 1 levels of laser light can be hazardous. This product uses diffractive optics to scatter the beam energy.
This scattering effect causes the energy concentration to drop below the exposure limits for momentary or accidental viewing at a relatively short distance from the laser aperture. As with all bright light-sources, when you operate this device in unsupervised general public areas, it is recommended that up-close access to the light be restricted or prevented and the beams be directed into locations where persons are not expected. This laser display device incorporates a CLASS 3B laser system which, by itself, may be hazardous.
However, this laser display product incorporates a protective housing and diffractive optics in its design so that there is no exposure or human access to laser radiation during operation or maintenance above the CLASS 1 limits. Each individual laser beamlet’s power is below the Class 1 limit of 0.39 mW. UNDER NO CIRCUMSTANCES shall attempts be made to open the protective housing or operate the device Nemo  me  All service to this laser display device requiring the protective housing to be opened and/ or removed shall be performed by service personnel or their authorized agents. Opening the protective housing voids the warranty. NO LASERS SHOULD BE POINTED INTO THE SKY WITHIN 10 NAUTICAL MILES (18.5 km) OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO STRAY BEAMS ARE PROJECTED INTO THE AIR. CHECK WITH YOUR LOCAL AIRPORT OR PROVINCIAL GUIDELINES FOR FURTHER INFORMATION.

Important Safety Notice

• Before using the projector, check if all components, including the projector, USB cable, USB adapter is intact.
• If any component is broken, contact our customer service team for repaired or replacement before operating the product.
• This is not a toy. Young children and toddler MUST be supervised while using this device at all times.”
• ONLY use manufacture-provided USB adapter. Use third-party USB adapter may permanently damage the projector.
• ONLY clean the surface or lens with a soft dry cloth.
• ONLY use the projector within rated operating temperature.
• ONLY place the project on a flat and horizontal surface.
• NEVER place the project close to fire, water or any dangerous environment.
• NEVER stare at the LED or laser when they are turned on.
• This unit is not waterproof. Please use and store this product indoors.
• If you plan not to use the projector for a long time, unplug its power and store it to a dry place.
• Before changing a disc, always power off the projector to avoid sudden brightness change.
• If the device is short-circuited or smoking, please unplug the power cord, stop using it and contact us immediately.

Specifications

Quick Start Guide

Before start operating the X1 projector, please read ‘Important Safety Notice’ section of this user manual. This projector is designed to ONLY be used in a dark room with low light environment.
Far best projection result, please ensure the projector is placed at a location that meets the following minimum requirement.

• A dark room {with no light pollution such as TV or table lamp }
• Projector facing towards a ceiling / weal that has at lease 9 ft x 9 ft flat surface
•  Projector being placed 5 ft- 8 ft from the ceiling wall

Step 1: Install the disc onto the disc tray. Remove the discs tray from the projector Align and press the disc to the disc tray Turn the disc counter clockwise to fixate the case, Hold the gear wheer on the disc tray with a ager when you turn the disc.
Step 2: Insert the disc tray to the projector with the front side facing towards lens. Step 3: Connect Odyssey X1 to USB cable and USB adapter.Step4 : Press the power button. The LED projection and laser stars will gradually Ruminate. Step. 5: Rotate the focus dial to adjust the projection clarity until you get a clear image.Rotate clockwise AND counter-clockwise unti: the center of the projection image is clear and focused
YOU MUST ADJUST FOCUS DIAL in order to get a  cellar image of the projection.

How to Adjust Focus Dial?

YOU MUST ADJUST FOCUS DIAL in order to get a clear image of the projection.
Rotate the focus dial clockwise or counter-clockwise until the center of the projection image is clear and focused.
For best clarity, you may need to try back and forth and rotate delicately when image is starting to get clear.
if you are setting up the projector for the first time, turn the focus dial clockwise all the way to the end, and then turn counter-clockwise gradually until you get a clear focus.
Due to the optical structure of the projector, the surrounding area may not be as clear as the center area for some discs, especially when the lens is placed at an angle, or the projection is not on a flat surface. This is normal due to principle of optical imaging. This is not a product defect. FOR BEST PROJECTION RESULT:
The darker the display area, the brighter the projection image will appear
Ensure the projector is facing towards as close to the center of the wall/ceilling as possible
Ensure the lens is facing perpendicularly to the wall/ceiling
Keep the center area is focused before the surrounding area

How to Install or Change a Disc:
The disc MUST be fixated to the disc tray before use. Tum off the projector before removing the disc tray to avoid sudden brightness change that may hurt your eyes.
To remove an existing disc, hold the gear wheel with one finger. Use two fingers of your other hand to hold the disc and turn it clockwise.To install a disc, align and press the disc to the disc tray. Then turn the disc counter-clockwise to fixate the disc. Hold the gear wheel on the disc tray with a finger when you turn the disc.

How to Adjust Projection Angle
Hold the top part of the projector and pull up the lens to adjust the projection angle. Avoid touching the lens. You can adjust angle to 0~90°. Spin the projector back and forth to find a ceiling/wall position that has largest flat surface area. . Rotate the lens all the way up, to point the projection to the ceiling.

**Other Functions

**

Child lock
Press and hold the laser button on the projector for 10 sec and laser will blink for 2 sec, which means the child lock is on.
When child lock is turned on, laser is disabled and cannot be turned on by either the laser button on the projector or remote control
To turn off child lock, press and hold the laser button for 10 sec again.
Timer
Press the timer button on the projector once to switch timer among 15 min, 30 min and 60 min. If no timer is set, the projector will turn off automatically after 5 hours of operation Alternatively, you can use the timer buttons on the remote control to set a timer
Adjust rotation speed
Press the rotation button on the projector once to switch rotation speed between slow, medium, fast level.
Alternatively, you can use the rotation speed button on the remote control to increase or decrease rotation speed.
Adjust laser brightness
Press the laser button on the projector once to switch laser brightness between low, medium, high level
Alternatively, you can use the brightness setting buttons on the remote control to increase or decrees laser brightness.
Blinking laser stars
Press the laser button on the projector 4 times to turn on blinking laser effect.
Alternatively, you can use the blinking laser button on the remote control to turn on blinking laser effect.

FAQ

Why does the projector turn off automatically after 3 hours?

The projector is designed to turn off automatically after 3 hours to increase the life span of the disc. For most of the discs, their life span may be significantly shortened if the projector is turned on over night. If you have strong need or other questions about using the projector for more than 3 hours, please email us at info@laviewusa.com

Why is the projection image is so vague?

Ensure the disc is installed correctly to the disc tray with correct side facing up Rotate the focus dial back and forth to adjust the focus. Read the ‘How to adjust focus dial’ section of this manual for more details The focus of each disc may slightly differ. You may need to adjust focus slightly when you change to a new disc Ensure the plastic film covering the lens is removed

Why cannot see any projection image?

Ensure the projector is placed in a dark room and all lights are turned off Ensure the projector is correctly powered Check if the USB adapter or USB cable is broken Press the power button once firmly Ensure the lens is not covered by any object

Can power the projector with a power bank?

You may use a power bank that has DC 5V 1A USB-A output to power the projector for a short time use

Can use it in the living room?

Yes. You may use the projector in any indoor rooms. However, for best projection result,please ensure the room is as dark as possible. Some discs may work when some ambient light is on, such as TV or a night light. But generally, the darker this display area, the brighter the projection image will appear

Why does laser look so bright on some discs?

While X1 is designed to fit comprehensive night light environment, some discs focus on the reality or clarity of space and universe. In such case, some black and white discs such as Earth and Moonand‘Southern Hemisphere 'do not t laser's brightness. You can try divergent discs that works better with laser. You can always adjust the laser brightness with remote control for best result

What should I do if the projector is broken?

This product carries a limted warranty against defects in workmanship and material. LaView agrees to replace the defective product free of charge within the stated warranty period. Please contact our customer service team immediately if the product becomes defective

Where can buy more discs?

You can purchase more discs on laviewusa.com, Amazon.com or shop via LaVew App.

Button Functions

Disc Gallery To purchase more discs, search ‘LabVIEW Projector Disc’ on Amazon.com or Laviewusa.com to buy more genuine Odyssey X1 discs
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between en 20cm the radiator your body: Use only the supplied antenna.

Need Help?
Live Chat:
Donwood LabVIEW App from App Store
Email: info@lavicwusa.com
Our professional technicians are committed to reply all requests within 24 hours
If you purchased from Amazon, you can also contact our professional customer service team in your Amazon account
Product Warranty
Your LaView product is protected by a 1-year warranty from the purchase date. For more information on repairs, exchange, and other policies, please visit www.laviewusa.com
Please send all inquiries through the Contact Form on our website, or email us at info@laviewusa.com. And our technicians would be glad to assist you.
Home Security Simplified
www.laviewusa.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>