EKLEVOR VC594 Wireless Microphone Instruction Manual

VC594 Wireless Microphone
Instruction Manual

Welcome to product

Thank you for showing your confidence in us by purchasing the VC594. This manual contains important instructions for setting up and operating your equipment. Please take a few minutes to read the instructions elow carefully before  operating the equipment. Please keep the manual for future reference. Have fun and impress your audience!

Specification

ALL AROUND
Frequency band: U band
Frequency stabilization: <+20ppm
Dynamic range: more than 80dB
TH.D at 1 KHz: Less than 0.5%
Frequency response: 40Hz-18KHz +3dB
Audio output level: 0- ±400mv, mix out 0- ±200mv
Temperature range: -10C to 50°C
FIXED RECEIVER
Signal/noise ratio: >80dB
Image-frequency rejection: >70dB
Border upon channel rejection: >70dB
S/N Ratio:< 12dBu (sind=20dB)
De-emphasis: 50 us
Working voltage: DC 12V
Working current: < 300mA
HANDING MICROPHONE
Frequency stabilization: <+20ppm
RF output(h): +13dBm
Modulation type: fm, f3f
Max deviation: ±20kHz
Microphone pickup: Moving coil
Power supply: 2(1.5V) Battery
Noise control: eliminating noise

Note

1. The unit only contains wireless microphone system, you need extra equipment to output the sound.
2. Check if your soundbar or speaker has AUX or MIC interface. Otherwise cannot connect. The volume of the AUX interface will be lower than that of the MIC interface, which is normal. If you need to connect other interfaces such as  RCA, please provide your own adapter.
3. If there is noise or electric current, please reconnect to make sure the installation is correct and the plug connection is tight.
4. Please install the microphone battery correctly, please pay attention to the “+ -” direction of the battery.
5. The receiver must place larger than one meter distance the ground and the wall, the antenna must perpendicular ground, otherwise it will affect the receiver’s result.
6. When use the receiver, it must avoid to place at the dead angle and keep the receiver signal in good condition.
7. Please hold the microphone carefully, and don’t drop it to avoid any serious damage.
8. Please don’t use old and new batteries together in the microphone.
9. If you will not use it for a long time, please turn OFF the system and take out the AA batteries.

RECEIVER FRONT PANEL FEATURES AND INSTRUCTIONS

1. CD POWER Button: Press the power switch.
2. Microphone A volume control: Adjust the output volume. Clockwise rotation, the volume increase; Counterclockwise, the volume decrease.
3. RF-A LED: A microphone RF signal display
4. LCD Display: LCD screen lights up after power on
5. RF-B LED: A microphone RF signal display
6. Microphone B volume control: Adjust the output volume. Clockwise rotation, the volume increase;
7. Counterclockwise, the volume decrease.

1. Mixing 6.35mm Output (A+B)
2. DC 12V Power Input

TRANSMITTER FUNCTION AND DESCRIPTION

1. Metal Grill & Cartridge
2. Digital Display: Frequency, Battery Volume, Channel
3. ONIOFF Switch: Press for 3 seconds
4. Battery box: unscrew bottom tube and put in AA battery

1. Battery Display (BATT): Shows the battery dump energy. When the battery is low, this icon will flash, please replace with new batteries to ensure the transmitter is working normally.
2. CHANNEL: Show the working channel of transmitter.
3. FREQUENCY: Show the working frequency.

SYSTEM SETTINGS

1. Power on the receiver, then the LCD screen will be light up.
2. Pull up the antenna A and the antenna B, make them perpendicular to the machine.
3. Use the audio cable hook up the receiver output jack and amplifier or active speakers input jack.
4. Install AA batteries into the microphone and turn the volume to the minimum, then begin to turn on the microphone. The receiver will automatically match the microphone, and the RF LED signal indicator will be light up.
5. Use the volume knob on the receiver to adjust to the appropriate volume, then it can be used normally.

Common troubleshooting

No Sound or sound is weak| Transmitter’s display is not lit| Turn on the transmitter. Make sure the battery +/pole is correct. Replace new battery
---|---|---
Receiver RF LED indicator is lit| Adjust the volume of receiver. Check the cable connection between receiver and Amplifier/Mixer. The product is mainly used to insert the MIC interface, the volume of the AUX interface will be lower than that of the MIC interface, which is normal.
Receiver RF indicator is not lit. Transmitter display is lit| Remove the nearby metal items from receiver. Check if there is barrier between transmitter and receiver. Make the transmitter close to the receiver.
BATT icon flashing| Replace battery
Distortion or Squeal| Receiver RF indicator is ON| 1.The microphone is too close to the speaker or the volume is adjusted too high, please turn down the volume of speaker or keep away from speaker.
2.Remove the nearby interference source (eg. CD player, PC, Digital device, in-Ear monitor system). Change the frequency of the transmitter. Replace battery. If several systems are used at same time, please increase the frequency space.
The distortion level is gradually increasing| Transmitter power indicator flashes| Replace the transmitter battery

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>